Huawei NetEngine80E Configuration Manual - Reliability page 81

HUAWEI NetEngine80E/40E Router
Configuration Guide - Reliability
3.
Step 3 Configure E-APS
1.
Issue 02 (2011-09-10)
[PE3-explicit-path-path] next hop 105.1.1.1
[PE3-explicit-path-path] next hop 102.1.1.1
[PE3-explicit-path-path] next hop 1.1.1.1
Configure MPLS TE.
# Configure PE1
[PE1] interface tunnel 1/0/0
[PE1-Tunnel1/0/0] ip address unnumbered interface LoopBack0
[PE1-Tunnel1/0/0] tunnel-protocol mpls te
[PE1-Tunnel1/0/0] destination 4.4.4.4
[PE1-Tunnel1/0/0] mpls te tunnel-id 1
[PE1-Tunnel1/0/0] mpls te path explicit-path path1
[PE1-Tunnel1/0/0] mpls te reserved-for-binding
[PE1-Tunnel1/0/0] mpls te commit
[PE1-Tunnel1/0/0] quit
[PE1] interface tunnel 2/0/0
[PE1-Tunnel2/0/0] ip address unnumbered interface LoopBack0
[PE1-Tunnel2/0/0] tunnel-protocol mpls te
[PE1-Tunnel2/0/0] destination 5.5.5.5
[PE1-Tunnel2/0/0] mpls te tunnel-id 2
[PE1-Tunnel2/0/0] mpls te path explicit-path path2
[PE1-Tunnel2/0/0] mpls te reserved-for-binding
[PE1-Tunnel2/0/0] mpls te commit
[PE1-Tunnel2/0/0] quit
[PE1] tunnel-policy ct1
[PE1-tunnel-policy-ct1] tunnel select-seq cr-lsp load-balance-number 1
[PE1-tunnel-policy-ct1] quit
[PE1] tunnel-policy ct2
[PE1-tunnel-policy-ct2] tunnel select-seq cr-lsp load-balance-number 1
[PE1-tunnel-policy-ct2] quit
# Configure PE2
[PE2] interface tunnel 1/0/0
[PE2-Tunnel1/0/0] ip address unnumbered interface LoopBack0
[PE2-Tunnel1/0/0] tunnel-protocol mpls te
[PE2-Tunnel1/0/0] destination 1.1.1.1
[PE2-Tunnel1/0/0] mpls te tunnel-id 1
[PE2-Tunnel1/0/0] mpls te path explicit-path path
[PE2-Tunnel1/0/0] mpls te reserved-for-binding
[PE2-Tunnel1/0/0] mpls te commit
[PE2-Tunnel1/0/0] quit
[PE2] tunnel-policy ct
[PE2-tunnel-policy-ct] tunnel select-seq cr-lsp load-balance-number 1
[PE2-tunnel-policy-ct] quit
# Configure PE3
[PE3] interface tunnel 1/0/0
[PE3-Tunnel1/0/0] ip address unnumbered interface LoopBack0
[PE3-Tunnel1/0/0] tunnel-protocol mpls te
[PE3-Tunnel1/0/0] destination 1.1.1.1
[PE3-Tunnel1/0/0] mpls te tunnel-id 2
[PE3-Tunnel1/0/0] mpls te path explicit-path path
[PE3-Tunnel1/0/0] mpls te reserved-for-binding
[PE3-Tunnel1/0/0] mpls te commit
[PE3-Tunnel1/0/0] quit
[PE3] tunnel-policy ct
[PE3-tunnel-policy-ct] tunnel select-seq cr-lsp load-balance-number 1
[PE3-tunnel-policy-ct] quit
Configure APS on PE2, PE3, and CE2.
# Configure PE2.
[PE2] interface atm 1/0/1
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
3 APS Configuration
64