Huawei NetEngine80E Configuration Manual - Reliability page 318

HUAWEI NetEngine80E/40E Router
Configuration Guide - Reliability
<HUAWEI> system-view
[HUAWEI] sysname RouterA
[RouterA] interface eth-trunk 1
[RouterA-Eth-Trunk1] undo shutdown
[RouterA-Eth-Trunk1] ip address 100.1.1.1 24
[RouterA-Eth-Trunk1] least active-linknumber 1
[RouterA-Eth-Trunk1] quit
[RouterA] interface gigabitethernet 1/0/0
[RouterA-GigabitEthernet1/0/0] undo shutdown
[RouterA-GigabitEthernet1/0/0] eth-trunk 1
[RouterA-GigabitEthernet1/0/0] quit
[RouterA] interface gigabitethernet 2/0/0
[RouterA-GigabitEthernet2/0/0] undo shutdown
[RouterA-GigabitEthernet2/0/0] eth-trunk 1
[RouterA-GigabitEthernet2/0/0] quit
# Create an Eth-Trunk interface on Router B and set the lower threshold of Eth-Trunk member
links in the Up state to 1.
<HUAWEI> system-view
[HUAWEI] sysname RouterB
[RouterB] interface eth-trunk 1
[RouterB-Eth-Trunk1] undo shutdown
[RouterB-Eth-Trunk1] ip address 100.1.1.2 24
[RouterB-Eth-Trunk1] least active-linknumber 1
[RouterB-Eth-Trunk1] quit
[RouterB] interface gigabitethernet 1/0/0
[RouterB-GigabitEthernet1/0/0] undo shutdown
[RouterB-GigabitEthernet1/0/0] eth-trunk 1
[RouterB-GigabitEthernet1/0/0] quit
[RouterB] interface gigabitethernet 2/0/0
[RouterB-GigabitEthernet2/0/0] undo shutdown
[RouterB-GigabitEthernet2/0/0] eth-trunk 1
[RouterB-GigabitEthernet2/0/0] quit
After the configurations are complete, run the display interface eth-trunk command on Router
A or Router B. You can view that the status of the interface is Up.
Use the display on Router A as an example.
[RouterA] display interface eth-trunk 1
Eth-Trunk1 current state : UP
Line protocol current state : UP
Last line protocol up time: 2007-11-19, 12:17:09
Description: Eth-Trunk1 Interface
Route Port,Hash arithmetic : According to flow,Maximal BW: 4G, Current BW: 4G, The
Maximum Transmit Unit is 1500
Internet Address is 100.1.1.1/24
IP Sending Frames" Format is PKTFMT_ETHNT_2, Hardware address is 00e0-fc90-5851
Physical is ETH_TRUNK
-----------------------------------------------------
PortName
-----------------------------------------------------
Issue 02 (2011-09-10)
NOTE
By default, the lower threshold of Eth-Trunk member links in the Up state is 1. It is configurable based on
networking environments.
Last 300 seconds input rate 0 bits/sec, 0 packets/sec
Last 300 seconds output rate 0 bits/sec, 0 packets/sec
Realtime 0 seconds input rate 0 bits/sec, 0 packets/sec
Realtime 0 seconds output rate 0 bits/sec, 0 packets/sec
Input: 0 packets,0 bytes
0 unicast,0 broadcast,0 multicast
0 errors,0 drops
Output:0 packets,0 bytes
0 unicast,0 broadcast,0 multicast
0 errors,0 drops
Input bandwidth utilization
Output bandwidth utilization : 0.01%
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
: 0.00%
Status Weight
5 BFD Configuration
301