Optional) Configuring Cc And Cv For A Pw - Huawei NetEngine80E Configuration Manual - Reliability

HUAWEI NetEngine80E/40E Router
Configuration Guide - Reliability
system-view
The system view is displayed.
Step 2 Run:
mpls-tp meg
A MEG is created, and the MEG view is displayed.
Step 3 Run:
me l2vc
ip | ttl ttl-number ] mep-id mep-id remote-mep-id remote-mep-id
An ME is created and bound to a single-segment or multi-segment PWE3 PW.
l If the PW is a single-segment PW, the OAM monitoring configurations are as follows:
l Specify remote-peer-ip or ttl for monitoring a multi-segment PW.
----End

10.3.3 (Optional) Configuring CC and CV for a PW

The CC and CV functions provided by MPLS-TP OAM can be configured to check continuous
connectivity and forwarding correctness of a PW.
Context
Continuity check (CV) and connectivity verification (CV) are two different MPLS-TP OAM
functions. CC checks loss of continuity (LOC) defects between two MEPs in a MEG. CV is used
to detect consistency of configurations on two MEPs in a MEG or in different MEGs. In real
Issue 02 (2011-09-10)
meg-name
peer-ip peer-ip vc-id vc-id vc-type vc-type [ remote-peer-ip remote-peer-
– Run the me l2vc peer-ip peer-ip vc-id vc-id vc-type vc-type mep-id mep-id remote-
mep-id remote-mep-id command on the local MEP to create an ME and bind it to the
single-segment PWE3 PW.
– Run the me l2vc peer-ip peer-ip vc-id vc-id vc-type vc-type mep-id mep-id remote-
mep-id remote-mep-id command on the RMEP to create an ME and bind the ME to the
same single-segment PWE3 PW.
– The procedure for binding an ME to a multi-segment PW by specifying remote-peer-
ip is as follows:
– Run the me l2vc
peer-ip mep-id mep-id remote-mep-id remote-mep-id command on the local MEP
to create an ME, bind it to a multi-segment PWE3 PW, and specify the IP address of
the RMEP of the multi-segment PWE3 PW.
– Run the me l2vc
peer-ip mep-id mep-id remote-mep-id remote-mep-id command on the RMEP to
create an ME, bind it to the same multi-segment PWE3 PW, and specify the IP address
of the RMEP of the multi-segment PWE3 PW.
– The procedure for binding an ME to a multi-segment PW by specifying ttl is as follows:
– Run the me l2vc
mep-id remote-mep-id remote-mep-id command on the local MEP to create an ME
and bind it to a multi-segment PWE3 PW.
– Run the me l2vc
mep-id remote-mep-id remote-mep-id command on the RMEP to create an ME and
bind it to the same multi-segment PWE3 PW.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
peer-ip peer-ip vc-id vc-id vc-type vc-type remote-peer-ip remote-
peer-ip peer-ip vc-id vc-id vc-type vc-type remote-peer-ip remote-
peer-ip peer-ip vc-id vc-id vc-type vc-type ttl ttl-number mep-id
peer-ip peer-ip vc-id vc-id vc-type vc-type ttl ttl-number mep-id
10 MPLS-TP OAM Configuration
678