Table of Contents
Advertisement
Table of Contents
Table 3-9:
Valve Operating States OPT 50B installed ..................................................................................60
Table 3-10:
Internal Span Gas Generator Valve Operating States OPT 50G ................................................63
Table 3-11:
Possible Warning Messages at Start-Up .....................................................................................66
Table 4-1:
Analyzer Operating Modes ..........................................................................................................74
Table 4-2:
Test Functions Defined ................................................................................................................75
Table 4-3:
Warning Messages Defined .........................................................................................................77
Table 4-4:
Primary Setup Mode Features and Functions .............................................................................79
Table 4-5:
Secondary Setup Mode Features and Functions ........................................................................80
Table 5-1:
IND Mode Analog Output Assignments .......................................................................................86
Table 5-2:
Password Levels ..........................................................................................................................93
Table 5-3:
Variable Names (VARS) ............................................................................................................100
Table 5-4:
Diagnostic Mode (DIAG) Functions ...........................................................................................102
Table 5-5:
DIAG - Analog I/O Functions .....................................................................................................105
Table 5-6:
Analog Output Voltage Range Min/Max ....................................................................................107
Table 5-7:
Voltage Tolerances for the TEST CHANNEL Calibration ..........................................................111
Table 5-8:
Current Loop Output Check .......................................................................................................115
Table 5-9:
Test Channels Functions available on the T200's Analog Output .............................................120
Table 6-1:
COM Port Communication Modes .............................................................................................124
Table 6-2:
Ethernet Status Indicators..........................................................................................................129
Table 6-4:
RS-232 Communication Parameters for Hessen Protocol ........................................................138
Table 6-5:
Teledyne API's Hessen Protocol Response Modes ..................................................................141
Table 6-6:
Default Hessen Status Flag Assignments .................................................................................145
Table 7-1:
Front Panel LED Status Indicators for DAS ...............................................................................147
Table 7-2:
DAS Data Channel Properties ...................................................................................................149
Table 7-3:
DAS Data Parameter Functions ................................................................................................157
Table 8-1:
Terminal Mode Software Commands ........................................................................................170
Table 8-2:
Teledyne API's Serial I/O Command Types ..............................................................................171
Table 9-1:
IZS Option Valve States with CAL_ON_NO
Table 9-2:
AUTOCAL Modes ......................................................................................................................197
Table 9-3:
AutoCal Attribute Setup Parameters ..........................................................................................198
Table 9-4:
Example AutoCal Sequence ......................................................................................................199
Table 9-5:
Calibration Data Quality Evaluation ...........................................................................................203
Table 11-1:
T200 Maintenance Schedule .....................................................................................................208
Table 11-2:
Predictive Uses for Test Functions ............................................................................................209
Table 12-1:
Front Panel Warning Messages ................................................................................................230
Table 12-2:
Test Functions - Indicated Failures ............................................................................................232
Table 12-3:
Test Channel Outputs as Diagnostic Tools ...............................................................................235
Table 12-4:
Relay PCA Watchdog LED Failure Indications ..........................................................................236
Table 12-5:
Relay PCA Status LED Failure Indications ................................................................................237
Table 12-6:
DC Power Test Point and Wiring Color Codes ..........................................................................249
Table 12-7:
DC Power Supply Acceptable Levels ........................................................................................250
Table 12-8:
Relay PCA Control Devices .......................................................................................................250
Table 12-9:
Analog Output Test Function - Nominal Values Voltage Outputs .............................................251
Table 12-10:
Status Outputs Check ................................................................................................................253
Table 12-11:
T200 Control Input Pin Assignments and Corresponding Signal I/O Functions ........................254
Table 13-1:
List of Interferents ......................................................................................................................290
Table 13-2:
T200 Valve Cycle Phases ..........................................................................................................293
Table 13-3:
T200 Gas Flow Rates ................................................................................................................295
Table 13-4:
Relay PCA Status LED's ............................................................................................................312
Table 13-5:
Thermocouple Configuration Jumper (JP5) Pin-Outs ................................................................315
Table 13-6:
AC Power Configuration for Internal Pumps (JP7) ....................................................................324
Table 13-7:
Power Configuration for Standard AC Heaters (JP2) ................................................................325
Table 13-8:
Power Configuration for Optional Heaters (JP6) .......................................................................326
xiv
Teledyne API – T200 NO/NO
Turned ON ..........................................................187
2
/NO
Analyzer Operation Manual
2
X
06858E DCN7057
Advertisement
Table of Contents
Troubleshooting
