Teledyne T200 Operation Manual page 14

Table of Contents
FIGURES
Figure 3-1: Front Panel Layout .......................................................................................................................25
Figure 3-2: Display Screen and Touch Control ..............................................................................................26
Figure 3-3: Display/Touch Control Screen Mapped to Menu Charts .............................................................28
Figure 3-4: Rear Panel Layout - Base Unit ...................................................................................................29
Figure 3-5: Internal Layout - Top View with IZS Option ................................................................................31
Figure 3-6: Internal Layout - Top View Showing Other Options ....................................................................32
Figure 3-7: Analog In Connector ....................................................................................................................34
Figure 3-8: Analog Output Connector ............................................................................................................35
Figure 3-9: Current Loop Option Installed on the Motherboard .....................................................................36
Figure 3-10: Status Output Connector .............................................................................................................37
Figure 3-11: Energizing the T200 Control Inputs .............................................................................................38
Figure 3-12: Concentration Alarm Relay ..........................................................................................................39
Figure 3-13 Rear Panel Connector Pin-Outs for RS-232 Mode ......................................................................42
Figure 3-14: Default Pin Assignments for CPU COM Port Connector (RS-232). ............................................43
Figure 3-15: Jumper and Cables for Multidrop Mode .......................................................................................45
Figure 3-16: RS-232-Multidrop PCA Host/Analyzer Interconnect Diagram .....................................................46
Figure 3-17: Gas Line Connections from Calibrator - Basic T200 Configuration ............................................50
Figure 3-18: Gas Line Connections from Bottled Span Gas - Basic T200 Configuration ...............................51
Figure 3-19: Pneumatics, Basic Configuration .................................................................................................53
Figure 3-20: Rear Panel Layout with Z/S Valve Options (OPT 50A) ...............................................................54
Figure 3-21: Gas Line Connections for T200 with Z/S Valves Option (OPT 50A) ...........................................54
Figure 3-22: Pneumatics with Zero/Span Valves OPT 50A .............................................................................56
Figure 3-23: Rear Panel Layout with Ambient Zero/Pressurized Span Valves OPT 50B ................................57
Figure 3-24: Gas Line Connection w/Ambient Zero/Pressurized Span Valves (OPT 50B) .............................58
Figure 3-25: Pneumatics with Ambient Zero/Pressurized Span Valves (OPT 50B) ........................................59
Figure 3-26: Rear Panel Layout with Internal Span Source (IZS) OPT 50G ...................................................61
Figure 3-27: Pneumatics with the Internal Span Gas Generator (OPT 50G)...................................................62
Figure 3-28: Pneumatics for Sample Conditioner OPT 86A ............................................................................63
Figure 4-1: Front Panel Display ......................................................................................................................73
Figure 4-2: Viewing T200 Test Functions ......................................................................................................75
Figure 5-1: Analog Output Connector Pin Out ...............................................................................................83
Figure 5-2. SETUP - COM Menu ...................................................................................................................98
Figure 5-3. COMM- Machine ID ....................................................................................................................99
Figure 5-4: Accessing the DIAG Submenus ................................................................................................103
Figure 5-5: Accessing the Analog I/O Configuration Submenus ..................................................................106
Figure 5-6: Setup for Checking / Calibrating DCV Analog Output Signal Levels .........................................111
Figure 5-7: Setup for Checking / Calibration Current Output Signal Levels Using an Ammeter..................113
Figure 5-8: Alternative Setup Using 250Ω Resistor for Checking Current Output Signal Levels ................115
Figure 6-1. COM - Communication Modes Setup .......................................................................................125
Figure 6-2. COM - COM Port Baud Rate ....................................................................................................126
Figure 6-3. COM - COM1 Test Port .............................................................................................................127
Figure 6-4. COM - LAN /Internet Manual Configuration ...............................................................................130
Figure 6-5. COM - LAN / Internet Automatic Configuration (DHCP) ...........................................................132
Figure 6-6. COM - Change Hostname........................................................................................................133
Figure 7-1: Default DAS Channels Setup ....................................................................................................152
Figure 7-2: APICOM Remote Control Program Interface .............................................................................166
Figure 7-3: Sample APICOM User Interface for Configuring the DAS .........................................................167
Figure 7-4: DAS Configuration Through a Terminal Emulation Program .....................................................168
Figure 8-1: Remote Access by Modem ........................................................................................................173
Figure 9-1: Set up for Manual Calibrations/Checks of T200's in Base Configuration w/ a Gas Dilution
Calibrator....................................................................................................................................182
Figure 9-2: Set up for Manual Calibrations/Checks of T200's in Base Configuration w/ Bottled Gas .........182
Figure 9-3: Pneumatic Connections for T200 Precision Calibration when IZS Generator Present .............186
Figure 9-4: Pneumatic Connections for Manual Calibration/Checks with the Internal Span Gas Generator187
Figure 11-1 Replacing the Particulate Filter ..................................................................................................210
xii
Teledyne API - T200 NO/NO
/NO Analyzer Operation Manual
2 X
06858E DCN7057