Table of Contents
Advertisement
Teledyne API – T200 NO/NO
Figure 11-2:
Particle Filter on O
Figure 11-3:
Ozone Cleanser Assembly ........................................................................................................212
Figure 11-4:
Zero Air Scrubber Assembly ......................................................................................................218
Figure 11-5:
NO
Converter Assembly ...........................................................................................................220
2
Figure 11-6:
Reaction Cell Assembly .............................................................................................................221
Figure 11-7:
Critical Flow Orifice Assembly ...................................................................................................223
Figure 12-1:
Example of Signal I/O Function .................................................................................................234
Figure 12-2:
CPU Status Indicator .................................................................................................................236
Figure 12-3:
Relay PCA Status LEDS Used for Troubleshooting ..................................................................237
Figure 12-4:
Location of DC Power Test Points on Relay PCA .....................................................................249
Figure 12-5:
Typical Set Up of Status Output Test ........................................................................................253
Figure 12-6:
Pressure / Flow Sensor Assembly .............................................................................................255
Figure 12-7:
Setup for determining NO
Figure 12-8:
Pre-Amplifier Board Layout ........................................................................................................275
Figure 12-9:
T200 Sensor Assembly ..............................................................................................................277
Figure 12-10:
Relay PCA with AC Relay Retainer In Place .............................................................................279
Figure 12-11:
Relay PCA Mounting Screw Locations .....................................................................................279
Figure 13-1:
Reaction Cell with PMT Tube and Optical Filter ........................................................................285
Figure 13-2:
T200 Sensitivity Spectrum .........................................................................................................286
Figure 13-3:
NO
NO Conversion ...............................................................................................................286
2
Figure 13-4:
Pneumatic Flow During the Auto Zero Cycle .............................................................................288
Figure 13-5.
Vacuum Manifold, Standard Configuration ................................................................................292
Figure 13-6:
Flow Control Assembly & Critical Flow Orifice...........................................................................293
Figure 13-7:
Location of Flow Control Assemblies & Critical Flow Orifices ...................................................295
Figure 13-8:
Ozone Generator Principle ........................................................................................................297
Figure 13-9:
Semi-Permeable Membrane Drying Process ............................................................................297
Figure 13-10:
T200 Sample Dryer ....................................................................................................................298
Figure 13-11:
T200 Electronic Block Diagram .................................................................................................302
Figure 13-12:
CPU Board .................................................................................................................................304
Figure 13-13:
Relay PCA Layout (P/N 045230100) .........................................................................................310
Figure 13-14:
Relay PCA P/N 045230100 with AC Relay Retainer in Place ...................................................311
Figure 13-15:
Status LED Locations – Relay PCA ...........................................................................................312
Figure 13-16:
Heater Control Loop Block Diagram. .........................................................................................314
Figure 13-17:
Thermocouple Configuration Jumper (JP5) Pin-Outs ................................................................316
Figure 13-18:
Basic PMT Design .....................................................................................................................317
Figure 13-19:
PMT Preamp Block Diagram .....................................................................................................318
Figure 13-20:
Typical Thermo-Electric Cooler .................................................................................................319
Figure 13-21:
PMT Cooling System Block Diagram .........................................................................................320
Figure 13-22:
Power Distribution Block Diagram .............................................................................................322
Figure 13-23:
Location of AC power Configuration Jumpers ...........................................................................323
Figure 13-24:
Pump AC Power Jumpers (JP7) ................................................................................................324
Figure 13-25:
Typical Set Up of AC Heater Jumper Set (JP2).........................................................................325
Figure 13-26:
Typical Jumper Set (JP2) Set Up of Heaters ............................................................................326
Figure 13-27:
Front Panel and Display Interface Block Diagram .....................................................................327
Figure 13-28:
Basic Software Operation ..........................................................................................................328
TABLES
Table 1-1.
Analyzer Options ..........................................................................................................................16
Table 2-2:
T200 Software Settings for EPA Reference ................................................................................20
Table 3-1:
Ventilation Clearance ...................................................................................................................24
Table 3-5:
Analog Output Pin Assignments ..................................................................................................35
Table 3-6:
Status Output Pin Assignments ...................................................................................................37
Table 3-7:
Control Input Pin Assignments ....................................................................................................38
Table 3-8:
Zero/Span Valves Operating States OPT 50A ............................................................................56
06858E DCN7057
/NO
Analyzer Operation Manual
2
X
Supply Air Dryer.........................................................................................211
3
NO Efficiency – T200 Base Configuration .................................259
2
Table of Contents
xiii
Advertisement
Table of Contents
Troubleshooting
