Teledyne T100 Instruction Manual page 340

Teledyne ML - T100 UV Fluorescence SO2 Analyzer
Table A-3:
TEST FUNCTION
RANGE RANGE=500.0 PPB
SO2 RNG=500.0 PPB
RANGE1 RANGE1=500.0 PPB
SO2 RN1=500.0 PPB
RANGE2 RANGE2=500.0 PPB
SO2 RN2=500.0 PPB
CO2RANGE CO2 RNG=100 PCT
O2RANGE O2 RNG=100 PCT
STABILITY STABIL=0.0 PPB
SO2 STB=0.0 PPB
O2 STB=0.0 PCT
CO2 STB=0.0 PCT
6
STABILITY2 STABIL2=0.0 PPB
SO2 STB2=0.0 PPB
O2 STB2=0.0 PCT
CO2 STB2=0.0 PCT
2
RESPONSE RSP=1.11(0.00) SEC
5
VACUUM VAC=9.1 IN-HG-A
SAMPPRESS PRES=29.9 IN-HG-A
SAMPFLOW SAMP FL=700 CC/M
PMTDET PMT=762.5 MV
NORMPMTDET NORM PMT=742.9 MV
UVDET UV LAMP=3457.6 MV
6
STABILITYUV UV STB=5.607 MV
LAMPRATIO LAMP RATIO=100.0 %
STRAYLIGHT STR. LGT=0.1 PPB
DARKPMT DRK PMT=19.6 MV
DARKLAMP DRK LMP=42.4 MV
SLOPE SLOPE=1.061
OFFSET OFFSET=250.0 MV
11
CO2SLOPE CO2 SLOPE=1.0000
11
CO2OFFSET CO2 OFFSET=0.00 %
10
O2SLOPE O2 SLOPE=0.980
10
O2OFFSET O2 OFFSET=1.79 %
HVPS HVPS=650 VOLTS
RCELLDUTY RCELL ON=0.00 SEC
RCELLTEMP RCELL TEMP=52.1 C
10
O2CELLTEMP O2 CELL TEMP=50.2 C
BOXTEMP BOX TEMP=35.5 C
Test Functions, Software Version G.4
MESSAGE TEXT
Test Measurements
3
3, 10, 11
3
3, 10, 11
3
3, 10, 11
11
10
3
3, 10
10
11
3
3, 10
10
11
05036 Rev D
APPENDIX A - Version Specific Software Documentation
DESCRIPTION
D/A range in single or auto-range modes.
D/A #1 range in independent range mode.
D/A #2 range in independent range mode.
D/A range for CO concentration.
2
D/A range for O concentration
2
Concentration stability #1.
Concentration stability #2.
Instrument response. Length of each signal processing loop.
Time in parenthesis is standard deviation.
Vacuum pressure.
Sample pressure.
Sample flow rate.
Raw PMT reading.
PMT reading normalized for temperature, pressure, auto-zero
offset, but not range.
UV lamp reading.
UV lamp stability reading.
UV lamp ratio of current reading divided by calibrated reading.
Stray light offset.
PMT dark offset.
UV lamp dark offset.
Slope for current range, computed during zero/span calibration.
Offset for current range, computed during zero/span calibration.
CO slope, computed during zero/span calibration.
2
CO offset, computed during zero/span calibration.
2
O slope, computed during zero/span calibration.
2
O offset, computed during zero/span calibration.
2
High voltage power supply output.
Reaction cell temperature control duty cycle.
Reaction cell temperature.
O sensor cell temperature.
2
Internal chassis temperature.
A-23