Studer OnAir 3000 Operating Instructions Manual page 323

OnAir Digital Mixing Consoles
GPO Function
CueSourceSelector
LinkOutput
FaderstartWithPFL
FaderstartWithoutPFL
TransparentOut
RedLight_ONAIR
* RedLight_ST1
RedLight_ST2
* RedLight_ST3
RedLight_CR
RedLight_PGMA
* RedLight_PGMB
RedLight_REC
* RedLight_5.1A
* RedLight_5.1B
MicMuteActive
ON
UserKey
TB
EnableTB
Locate
OnMaster
Next_Out
RedLight_Input
MicGroupActive
MicGroupReady
MicGroupOnAir
Setup
1: PrimaryDesk / *SecondaryDesk / Not Spec.
LastSnapshot
OutputRoutingOut
ForwardInput
ChannelUserKey
PFL
Generator
LSPModeOnRedLight
* OnAir 3000 only.
6-82 Configuration
Arguments
1: Cue CR / *Cue ST1
2: MonitorCueKey
GP Output pin
1: Logical Input
1: Logical Input
1: Device ID
-
-
-
-
-
-
-
-
-
-
1: Logical Input
1: Logical Input / Strip Channel / AUX / N–X Active if ON key is on
1: Device ID of a user key parameter
1: TB Sources: CR / *ST1 / ST2 / *ST3 /
/ External
2: TB Destinations: All TB destinations
1: Destination: All TB destinations
1: Logical Input
1: Logical Input
1: StartNextA/B_State
1: Logical Input
1: MicGroup
1: MicGroup
1: MicGroup
1: Setup1 | Setup 2
2: All / CR / *ST1 / ST2 / *ST3
3: string
1: Partial Output Routing
1: GP Input Pin
1: Logical Input | Master
2: User Function 1 | User Function 2
1: LogicalInput / StripChannel /
MasterFaders / ExtPFL
2: PFL (CR) / *PFL ST1
1: StaticHigh / StaticLow / Alternate
1: CR / *ST1 / ST2 / *ST3
2: Dim / Cut / Nothing / Cut, but allow TB
SW V6.0
Description
Active if the selected cue source is on
Links the GP output to another GPO function
Fader start with ON key and fader, or PFL
Fader start with ON key and fader
Active if the value of the specified parameter is different from
zero (this function is normally used for factory testing only).
Only 64-bit device ID numbers in hex format are accepted as argu-
ment 1 – i.e., 0x followed by 16 digits (e.g. 0x1122334455667788)
Active if the ON AIR LED is on
Active if Studio 1 red light indication is on
Active if Studio 2 red light indication is on
Active if Studio 3 red light indication is on
Active if Control Room red light indication is on
Active if PGM A is on air
Active if PGM B is on air
Active if REC is on air
Active if 5.1 A is On Air
Active if 5.1 B is On Air
Active if mic is muted
Active if the value of the specified user key parameter is true
Active if the specified Talkback from Source to Destination is
active (since SW V3.2, also Source = Destination is allowed)
Active if the specified talkback destination is enabled
Active if LOC/READY key of the logical input is on
Active if channel on master is active
Flashing if status = Ready, continuous if status = Next
Active if specified strip channel is ON
Active if ext. mic group key is Active or On Air
Active if ext. mic group key is Ready
Active if ext. mic group key is On Air
Active if the specified setup is active
Active if the last loaded Global Snapshot is the one with the
name specified by 'string'
Active if the cross points of the specified partial output routing
are set as specified by 'string'
Active if the specified input pin is active
Active if the value of the specified user key parameter is true.
If a channel user key on the desk (e.g. Fader Module) is assigned
to a Channel User Key parameter, and the 'ChannelUserKey' GPO
function connects that parameter to a GP output pin, the channel
user key can control the GPO.
Active if the specified input or master is assigned to the speci-
fied PFL bus
Creates the Level according to the mode specified by Argu-
ment 1.
StaticHigh: Level is always high
StaticLow: Level is always low
Alternate: Level is alternating (f is approx. 1 Hz)
Indicates LSPModeOnRedLight
Document generated: 10.10.14