Grandstream Networks UCM6510 User Manual page 241

Ip pbx
Hide thumbs Also See for UCM6510:
Table of Contents

Advertisement

UCM6510  first  before  using  remote  BLF  feature.  Please  note  the  SIP  end  points  need  support  event  list  
BLF  in  order  to  monitor  remote  extensions.
 
When  an  event  list  is  created  on  the  UCM6510  and  remote  extensions  are  added  to  the  list,  the  UCM6510  
will  send  out  SIP  SUBSCIRBE  to  the  remote  UCM6510  to  obtain  the  remote  extension  status.  When  the  
SIP   end   points   registers   and   subscribes   to   the   local   UCM6510   event   list,   it   can   obtain   the   remote  
extension  status  from  this  event  list.    
 
Once  successfully  configured,  the  event  list  page  will  show  the  status  of  total  extension  and  subscribers  for  
each   event   list.   Users   can   also   select   the   event   URI   to   check   the   monitored   extension's   status   and   the  
subscribers'  details.  
 
 
 
 
-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­
 
Note:  
To  configure  LDAP  sync,  please  go  to  UCM6510  web  GUI-­>PBX-­>Basic/Call  Routes-­>VoIP  Trunk.  
•  
You  will  see  "Sync  LDAP  Enable"  option.  Once  enabled,  please  configure  password  information  for  the  
remote  peer  UCM6510  to  connect  to  the  local  UCM6510.  Additional  information  such  as  port  number,  
LDAP  outbound  rule,  LDAP  Dialed  Prefix  will  also  be  required.  Both  the  local  UCM6510  and  remote  
UCM6510   need   enable   LDAP   sync   option   with   the   same   password   for   successful   connection   and  
synchronization.  
Currently  LDAP  sync  feature  only  works  between  two  UCM6510s.    
•  
(Theoretically)   Remote   BLF   monitoring   will   work   when   the   remote   PBX   being   monitored   is  
•  
non-­UCM6510   PBX.   However,   it   might   not   work   the   other   way   around   depending   on   whether   the  
non-­UCM6510  PBX  supports  event  list  BLF  or  remote  monitoring  feature.  
-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­  
 
 
 
 
 
 
 
 
 
 
 
 
Firmware  Version  1.0.2.5  
 
 
UCM6510  IP  PBX  User  Manual  
 
 
Page  240  of  317

Advertisement

Table of Contents
loading

Table of Contents