Sip  Settings/Tcp  And  Tls; Table  92:  Sip  Settings/Tcp  And  Tls - Grandstream Networks UCM6510 User Manual

Ip pbx
Hide thumbs Also See for UCM6510:
Table of Contents

Advertisement

Session  Expire  
Min  SE  
Session  Refresher  
 
SIP   S ETTINGS/TCP   a nd   T LS  
 
-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­  
 
Note:  
The  configuration  in  this  section  requires  system  reboot  to  take  effect.  
-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­  
 
TCP  Enable  
TCP  Bind   A ddress  
TLS  Enable  
TLS  Bind   A ddress  
TLS  Client  Protocol  
Firmware  Version  1.0.2.5  
 
Run  session  timer  only  when  requested  by  other  UA.    
Refuse  
•  
Do  not  run  session  timer.  
Configure  the  maximum  session  refresh  interval  (in  seconds).  The  default  
setting  is  1800.  
Configure  the  minimum  session  refresh  interval  (in  seconds).  The  default  
setting  is  90.  
Select  the  session  refresher  to  be  UAC  or  UAS.  The  default  setting  is  UAC.  
 
Table  92:  SIP  Settings/TCP  and  TLS  
Configure   to   allow   incoming   TCP   connections   with   the   UCM6510.   The  
default  setting  is  "No".  
Configure  the  IP  address  for  TCP  server  to  bind  to.  0.0.0.0  means  binding  
to  all  interfaces.  The  port  number  is  optional.  If  not  specified,  5060  will  be  
used.  
Configure   to   allow   incoming   TLS   connections   with   the   UCM6510.   The  
default  setting  is  "No".  
Configure  the  IP  address  for  TLS  server  to  bind  to.  0.0.0.0  means  binding  
to  all  interfaces.  The  port  number  is  optional.  If  not  specified,  5061  will  be  
used.  
 
Note:  
The   IP   address   must   match   the   common   name   (hostname)   in   the  
certificate.  Please  do  not  bind  a  TLS  socket  to  multiple  IP  addresses.  For  
details  on  how  to  construct  a  certificate  for  SIP,  please  refer  to  the  following  
document:  
http://tools.ietf.org/html/draft-­ietf-­sip-­domain-­certs  
Select   the   TLS   protocol   for   outbound   client   connections.   The   default  
UCM6510  IP  PBX  User  Manual  
 
 
Page  264  of  317

Advertisement

Table of Contents
loading

Table of Contents