Repeatability Adjustment - MUTOH Falcon II Outdoor Maintenance Manual

Notes :
Confirmation patterns are printed in the following sequence:
50, 64 inch model: 1A, 1B, 1A, 2A, 1A, 2B, 1A, 3A, 1A, 3B, 1A, 4A, 1A, 4B, 1B, 2A,
1B, 2B, 1B, 3A, 1B, 3B, 1B, 4A, 1B, 4B, 2A, 2B, 2A, 3A, 2A, 3B, 2A, 4A, 2A, 4B, 2B,
3A, 2B, 3B, 2B, 4A, 2B, 4B, 3A, 3B, 3A, 4A, 3A, 4B, 3B, 4A, 3B, 4B, 4A, 4B
87 inch model: 1A, 1B, 1A, 2A, 1A, 2B, 1A, 3A, 1A, 3B, 1A, 4A, 1A, 4B, 1A, 5A, 1A,
5B, 1A, 6A, 1A, 6B, 1A, 7A, 1A, 7B, 1A, 8A, 1A, 8B, 1B, 2A, 1B, 2B, 1B, 3A, 1B, 3B,
1B, 4A, 1B, 4B, 1B, 5A, 1B, 5B, 1B, 6A, 1B, 6B, 1B, 7A, 1B, 7B, 1B, 8A, 1B, 8B, 2A,
2B, 2A, 3A, 2A, 3B, 2A, 4A, 2A, 4B, 2A, 5A, 2A, 5B, 2A, 6A, 2A, 6B, 2A, 7A, 2A, 7B,
2A, 8A, 2A, 8B, 2B, 3A, 2B, 3B, 2B, 4A, 2B, 4B, 2B, 5A, 2B, 5B, 2B, 6A, 2B, 6B, 2B,
7A, 2B, 7B, 2B, 8A, 2B, 8B, 3A, 3B, 3A, 4A, 3A, 4B, 3A, 5A, 3A, 5B, 3A, 6A, 3A, 6B,
3A, 7A, 3A, 7B, 3A, 8A, 3A, 8B, 3B, 4A, 3B, 4B, 3B, 5A, 3B, 5B, 3B, 6A, 3B, 6B, 3B,
7A, 3B, 7B, 3B, 8A, 3B, 8B, 4A, 4B, 4A, 5A, 4A, 5B, 4A, 6A, 4A, 6B, 4A, 7A, 4A, 7B,
4A, 8A, 4A, 8B, 4B, 5A, 4B, 5B, 4B, 6A, 4B, 6B, 4B, 7A, 4B, 7B, 4B, 8A, 4B, 8B, 5A,
5B, 5A, 6A, 5A, 6B, 5A, 7A, 5A, 7B, 5A, 8A, 5A, 8B, 5B, 6A, 5B, 6B, 5B, 7A, 5B, 7B,
5B, 8A, 5B, 8B, 6A, 6B, 6A, 7A, 6A, 7B, 6A, 8A, 6A, 8B, 6B, 7A, 6B, 7B, 6B, 8A, 6B,
8B, 7A, 7B, 7A, 8A, 7A, 8B, 7B, 8A, 7B, 8B, 8A, 8B
Step 7 :
Tighten the screw fixing the head stationary plate.

7.8. REPEATABILITY ADJUSTMENT

Step 1 :
Start the self-diagnostic function.
Notes :
Refer to "Self-Diagnosis Function".
Step 2 :
Select "Adj:Bi-D".
Step 3 :
Print a repeatability pattern.
Step 4 :
Enlarge it using a magnifying glass. If the reference is on right side, adjust the dotted line on printing A using
positive values until it becomes straight.
Step 5 :
Enlarge it using a magnifying glass.
Step 6 :
If the reference is on left side, adjust the dotted line on printing A using negative values until it becomes
straight.
Falcon II Outdoor series printers – Maintenance Manual
243 AP-74065, Rev. 1.0, 21/11/03