Delta AH500 Hardware Operation Manual page 585

A H 5 0 0 H a r d w a r e a n d O p e r a t i o n M a n u a l
Error
Description
Code
The setting of the data exchange
16#9A12 for slave 18 in the PLC Link is
incorrect. (SM1590)
The setting of the data exchange
16#9A13 for slave 19 in the PLC Link is
incorrect. (SM1590)
The setting of the data exchange
16#9A14 for slave 20 in the PLC Link is
incorrect. (SM1590)
The setting of the data exchange
16#9A15 for slave 21 in the PLC Link is
incorrect. (SM1590)
The setting of the data exchange
16#9A16 for slave 22 in the PLC Link is
incorrect. (SM1590)
The setting of the data exchange
16#9A17 for slave 23 in the PLC Link is
incorrect. (SM1590)
The setting of the data exchange
16#9A18 for slave 24 in the PLC Link is
incorrect. (SM1590)
The setting of the data exchange
16#9A19 for slave 25 in the PLC Link is
incorrect. (SM1590)
The setting of the data exchange
16#9A1A for slave 26 in the PLC Link is
incorrect. (SM1590)
The setting of the data exchange
16#9A1B for slave 27 in the PLC Link is
incorrect. (SM1590)
The setting of the data exchange
16#9A1C for slave 28 in the PLC Link is
incorrect. (SM1590)
The setting of the data exchange
16#9A1D for slave 29 in the PLC Link is
incorrect. (SM1590)
The setting of the data exchange
16#9A1E for slave 30 in the PLC Link is
incorrect. (SM1590)
The setting of the data exchange
16#9A1F for slave 31 in the PLC Link is
incorrect. (SM1590)
The setting of the data exchange
16#9A20 for slave 32 in the PLC Link is
incorrect. (SM1590)
An error occurs when the master
16#9A21 communicates with slave 1 in the
PLC Link. (SM1591)
An error occurs when the master
16#9A22 communicates with slave 2 in the
PLC Link. (SM1591)
1 2 - 3 6
Solution
1. Check the program and the related special data
registers.
2. Set the PLC Link parameter in HWCONFIG again.
1. Check the program and the related special data
registers.
2. Set the PLC Link parameter in HWCONFIG again.
1. Check the program and the related special data
registers.
2. Set the PLC Link parameter in HWCONFIG again.
1. Check the program and the related special data
registers.
2. Set the PLC Link parameter in HWCONFIG again.
1. Check the program and the related special data
registers.
2. Set the PLC Link parameter in HWCONFIG again.
1. Check the program and the related special data
registers.
2. Set the PLC Link parameter in HWCONFIG again.
1. Check the program and the related special data
registers.
2. Set the PLC Link parameter in HWCONFIG again.
1. Check the program and the related special data
registers.
2. Set the PLC Link parameter in HWCONFIG again.
1. Check the program and the related special data
registers.
2. Set the PLC Link parameter in HWCONFIG again.
1. Check the program and the related special data
registers.
2. Set the PLC Link parameter in HWCONFIG again.
1. Check the program and the related special data
registers.
2. Set the PLC Link parameter in HWCONFIG again.
1. Check the program and the related special data
registers.
2. Set the PLC Link parameter in HWCONFIG again.
1. Check the program and the related special data
registers.
2. Set the PLC Link parameter in HWCONFIG again.
1. Check the program and the related special data
registers.
2. Set the PLC Link parameter in HWCONFIG again.
1. Check the program and the related special data
registers.
2. Set the PLC Link parameter in HWCONFIG again.
1. Check the communication setting in the master, and
the communication setting in slave 1.
2. Check the communication cable.
1. Check the communication setting in the master, and
the communication setting in slave 2.
2. Check the communication cable.