ABB ACS880 Firmware Manual page 210

210 Parameters
No. Name/Value
14.26 AI1 actual value
-22.000 ... 22.000
mA or V
14.27 DIO4 ON delay
0.00 ... 3000.00 s
14.27 AI1 scaled value
-32768.000 ...
32767.000
14.28 DIO4 OFF delay
0.00 ... 3000.00 s
14.28 AI1 force data
-22.000 ... 22.000
mA or V
14.29 AI1 HW switch
position
V
mA
14.30 AI1 unit selection
V
mA
14.31 RO status
0000b...1111b
Description
(Visible when 14.01 Module 1 type
Displays value of analog input AI1 in mA or V (depending on
whether the input is set to current or voltage).
This parameter is read-only.
Value of analog input AI1.
(Visible when 14.01 Module 1 type
Defines the activation delay for digital input/output DIO4.
See parameter 14.12 DIO1 ON
Activation delay for DIO4.
(Visible when 14.01 Module 1 type
Displays value of analog input AI1 after scaling. See
parameter 14.35 AI1 scaled at AI1
This parameter is read-only.
Scaled value of analog input AI1.
(Visible when 14.01 Module 1 type
Defines the deactivation delay for digital input/output DIO4.
See parameter 14.12 DIO1 ON
Deactivation delay for DIO4.
(Visible when 14.01 Module 1 type
Forced value that can be used instead of the true reading of
the input. See parameter
Forced value of analog input AI1.
(Visible when 14.01 Module 1 type
Shows the position of the hardware current/voltage selector
on the I/O extension module.
Note: The setting of the current/voltage selector must match
the unit selection made in parameter
selection. I/O module reboot either by cycling the power or
through parameter 96.08 Control board boot
validate any changes in the hardware settings.
Volts.
Milliamperes.
(Visible when 14.01 Module 1 type
Selects the unit for readings and settings related to analog
input AI1.
Note: This setting must match the corresponding hardware
setting on the I/O extension module (see the manual of the
I/O extension module). The hardware setting is shown by
parameter 14.29 AI1 HW switch
either by cycling the power or through parameter
Control board boot is required to validate any changes in the
hardware settings.
Volts.
Milliamperes.
(Visible when 14.01 Module 1 type
Status of relay outputs on the I/O extension module.
Example: 0001b = RO1 is energized, RO2 is de-energized.
Status of relay outputs.
= FIO-11 or FAIO-01)
= FIO-01 or FIO-11)
delay.
= FIO-11 or FAIO-01)
min.
= FIO-01)
delay.
= FIO-11 or FAIO-01)
14.22 AI force selection.
= FIO-11 or FAIO-01)
14.30 AI1 unit
is required to
= FIO-11 or FAIO-01)
position. I/O module reboot
= FIO-01 or FDIO-01)
Def/FbEq16
-
1000 = 1 mA
or V
0.00 s
100 = 1 s
-
1 = 1
0.00 s
100 = 1 s
0.000 mA
1000 = 1 mA
or V
-
2
10
mA
96.08
2
10
-
1 = 1