Blackmagicdesign ATEM Production Studio 4K Installation And Operation Manual page 27

CUT CUT CUT CUT DIP CUT CUT AUX 7 AUX 8 AUX 9 AUX 10
KEY 1 KEY 2 KEY 3 KEY 4 BORD STNG DVE AUX 1 AUX 2 AUX 3
Media Media
Camera Camera Camera Camera Camera Camera Color
Black Player Player
1 2 3 4 5 6 Bars
1 2
CUT CUT CUT CUT DIP CUT CUT CUT CUT CUT
BOX 1
KEY 1 KEY 2 KEY 3 KEY 4 BORD STNG DVE DSK 1 DSK 2 SSRC
Media Media
Camera Camera Camera Camera Camera Camera Camera Camera
Player Player Black
1 2 3 4 5 6 7 8
1 2
Change Network Settings from the System Control
1 On the broadcast panel system control menus, select the NETWRK SETUP
menu button.
If the broadcast panel has already established connection to the switcher, you can
access the NETWRK SETUP menu from the HOME menu by pressing the SHIFT and
CUT/FILL buttons simultaneously on the ATEM 1 M/E Broadcast Panel, or the SHIFT and
DEST SHIFT buttons in the M/E 1 block of the ATEM 2 M/E Broadcast Panel. This will
reveal the NETWRK SETUP menu button so you can select the network settings.
2 The broadcast panel's current IP address, net mask and gateway information is
displayed.
3 The next step is to decide if you want the panel to use a fixed IP address or to be
automatically assigned an IP address from a DHCP server. Select PANEL DHCP to set
this using the soft keys on the main display.
If you're connecting direct to a switcher without a network, then you won't have a
DHCP server to assign an IP address automatically, so you will want to select fixed.
ATEM Broadcast Panels are delivered with a fixed IP address set to 192.168.10.10, for a
direct connection.
However, if your network has lots of computers that automatically assign IP addresses
via DHCP, then you can also select DHCP on the panel so the panel can get its network
information automatically. This is possible on the panel, and it's only the switcher itself
that always requires a fixed IP, as the switcher needs to be found by the control panels
at a known fixed address on your network.
If you select DHCP, your network settings will be complete because the panel network
settings will be obtained from the network automatically.
4 If you have elected to use a fixed IP address, you now need to set this IP address
by selecting the PANEL IP menu button and use the knobs or the numeric keypad
to edit each field as required. Changing this IP address may cause the panel to lose
communication.
5 If the subnet mask and gateway address need to be set, then select the relevant
buttons on the system control buttons to set and use knobs or the numeric
keypad to edit.
6 When any settings have been changed, SAVE and REVERT menu buttons will become
available. Select SAVE to save the changes to the new network settings, or REVERT to
ignore the changes and revert to the current network settings.
AUX 11 AUX 12
DEST
SHIFT
AUX 4 AUX 5 AUX 6
SHIFT
Media Media
Color Color
Player Player
1 2
1 Key 2 Key
EFFECTS DSK
TRANS
KEYS KEYS
MEDIA
PLAYER
SHIFT
PANEL
SETUP
DEST
BOX 2 BOX 3 BOX 4 MACRO MACRO RECALL RECALL ON ON
1 1 & RUN SHIFT
PLAY PLAY LOOP LOOP RECORD RECORD
BKGD KEY 1 KEY 2
SHIFT
Media Media
Color Color Color DIP
Player Player
Bars 1 2 WIPE STNG
1 Key 2 Key
MIX
PREV
TRANS
SHIFT CUT AUTO
ON ON ON ON
BKGD KEY 1 KEY 2 KEY 3 KEY 4 FTB
BOX 4
M/E 2 M/E 2
PATT KEY
BOX 2
DIP
WIPE STNG DVE
MIX
BOX 4
M/E 1 M/E 1
PATT KEY
BOX 2
COLOR PREV
TRANS
CUT AUTO
ON ON
KEY 3 KEY 4
FTB
DVE
RECORD
PLAY
SHOW
RECALL
NAMES
LOOP STOP
DELETE
HOME
1 2 3
4 5 6
7 8 9
CAM 0 CLR
DSK 1 DSK 2
TIE TIE
DSK 1 DSK 2
CUT CUT
DSK 1 DSK 2
AUTO AUTO
Getting Started 27 27