Page 1

NOTICE Note that when converting this document from its original format to a .pdf file, some minor font and format changes may occur causing slight variations. When viewing and printing this document, we cannot guarantee that your specific PC or printer will support all of the fonts or graphics.
Page 2

R O G R A M M I N G A N U A L I N T - 1 0 2 6 ( I P K ) Document Revision 4 (Release 4000/4500)
Page 4

NEC Unified Solutions, Inc. reserves the right to change the specifications, functions, or features at any time without notice. NEC Unified Solutions, Inc. has prepared this document for use by its employees and customers. The information contained herein is the property of NEC Unified Solutions, Inc.
Page 6: Section 1 Time Chart

Programming can be accomplished using a PC or a Multiline Terminal. ECTION ANUAL RGANIZATION This manual provides instructions for programming the Electra Elite IPK system. Chapter 1 – Multiline Terminal Programming This chapter includes the basic information for programming the system. Chapter 2 – Memory Blocks This chapter includes all of the Memory Blocks used to program the system.
Page 7: Section 1 General Information

Electra Electra Elite IPK General Description Manual This manual provides general information about the system features, configuration, and standards. An overview of the Electra Elite IPK system that is useful when presenting information to potential customers is provided. Electra Electra Elite IPK System Hardware Manual...
Page 8

This manual provides general information about the Electra Electra Elite IPK ACD Plus features, installation procedures and feature programming. The NEC Electra Electra Elite IPK ACD Plus is an Automatic Call Distribution card that supports up to 40 Agents and 12 supervisors at one time.
Page 9

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ THIS PAGE INTENTIONALLY LEFT BLANK ___________________________________________________________________________________ Preface...
Page 10: Table Of Contents

TABLE OF CONTENTS ___________________________________________________________________________________ Chapter 1 Multiline Terminal Programming Section 1 General Information ................1-1 Section 2 Programming the System ..............1-1 Features of Programming ..............1-2 System Programming Modes ............1-3 Before Programming ................ 1-4 2.3.1 Check Points ..................1-4 2.3.2 Preliminary Points ................
Page 11: Table Of Contents

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-1-05 Start Time Selection ..................2-9 1-1-06 CO/PBX Incoming Ringing Alarm Time Selection ........2-11 1-1-07 Tie Line Delay Ringing Time Selection .............2-13 1-1-09 Manual Pause Selection ................2-16 1-1-11 System Transfer/Camp-On Selection ............2-18 1-1-12 Station Transfer/Camp-On Recall Time Selection ........2-19 1-1-13 CO Transfer Ring Pattern Selection ............2-21...
Page 12: Table Of Contents

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-54 Automated Attendant Transfer Ring Pattern ..........2-73 1-1-55 DID Line Ringing Pattern Selection ............2-75 1-1-57 CO/PBX Prepause Time Selection ............2-76 1-1-59 Synchronous Ringing Selection ..............2-77 1-1-60 8-Digit Matching Table Assignment ............2-78 1-1-61 8-Digit Matching Table to Class Assignment ..........2-80 1-1-62 System Speed Dial Override by Class Selection ........2-82...
Page 13: Table Of Contents

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-2-08 Specified Station Access Code Assignment ...........2-114 1-2-09~18 Customized Message 1~10 Assignment ..........2-116 1-2-19 Intercom Ring Pattern Selection .............2-117 1-2-20 Intercom Ring Tone Selection ..............2-119 1-2-21 PS Telephone Block Assignment ............2-120 1-2-22 Call Forward - No Answer Time Selection ..........2-122 1-2-23 System Call Park Recall Time Selection ..........2-124...
Page 14: Table Of Contents

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-4-08 Automated Attendant PBR Timeout Response Selection .......2-161 1-4-09 Automated Attendant PBR Start Time Selection ........2-162 1-4-11 Automated Attendant Message Day/Night Mode Selection ....2-163 1-4-12 Automated Attendant Message to Tenant Assignment ......2-164 1-4-13 Automated Attendant Answer Delay Time Assignment ......2-165...
Page 15: Table Of Contents

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-7-06 External Paging Timeout Selection ............2-200 1-7-07 External Ring Relay Pattern Selection ............2-202 1-7-08 External Speaker Chime Selection ............2-204 1-7-09 External Speaker Chime Start Time Selection ........2-205 1-8-01 SLT or Automated Attendant/DISA to CPU PBR Selection ....2-207 1-8-02 PBR Receive Level Assignment for Automated Attendant/DISA ....2-208...
Page 16: Table Of Contents

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-8-44 Enhanced 911 Alternate Route Assignment ...........2-251 1-8-45 Enhanced 911 Alternate Route Assignment (Maintenance Busy) ..2-252 1-8-46 Enhanced 911 Dialing Digit Assignment ..........2-254 1-8-47 Call Arrival Key Voice Mail Message Notification Assignment ....2-255 1-8-48 Automatic Daylight Saving Time Selection ..........2-256...
Page 17: Table Of Contents

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-12-02 ACD/UCD Overflow Time Selection ............2-305 1-13-00 PRT Channel Assignment ...............2-307 1-13-01 PRT Signal Format Selection ..............2-309 1-13-02 Clear Channel Selection .................2-311 1-13-03 Call by Call Service Selection ..............2-312 1-13-04 PRT B Channel Outgoing Priority Selection ..........2-313 1-13-05 PRT B Channel-to-Trunk Group Assignment ..........2-314...
Page 18: Table Of Contents

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-15-17 Centralized BLF Send Time Assignment ..........2-368 1-15-18 Centralized BLF Receive Extension Number Assignment ......2-370 1-15-19 Centralized 911 Allow/Deny Selection ............2-372 1-15-20 Centralized 911/Calling Party (CPN) Originating Number Selection ..2-374 1-15-21 Centralized 911 Look Ahead Routing Allow/ Deny Selection ....2-376 1-16-00 Auto Negotiation Yes/No Selection ............2-379...
Page 19: Table Of Contents

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 3-04 Trunk-to-Trunk Transfer Yes/No Selection ..........2-428 3-05 Trunk Incoming Answer Mode Selection ..........2-430 3-06 Automatic Tandem Trunk Assignment ............2-432 3-07 CO/PBX Ringing Variation Selection ............2-433 3-11 CO External Source Selection ..............2-434 3-12 Trunk-to-MOH Trunk Assignment ............2-435 3-14 Tie Line Type Assignment ...............2-436...
Page 20: Table Of Contents

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 3-52 ISDN Trunk Directory Number Assignment ..........2-479 3-53 Caller Name Indication Selection ............2-480 3-59 Automated Attendant Function Selection ..........2-481 3-61 DIT/ANA Delay Answer Time Selection ..........2-482 3-62 DIT Tenant Assignment ................2-484 3-63 DIT Weekend Mode Selection ..............2-485 3-64 DIT Night Mode Delay Answer Selection ..........2-486...
Page 21: Table Of Contents

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 4-23 Prime Line/Hot Line Assignment .............2-532 4-24 SLT Hookflash Assignment ..............2-534 4-26 DISA ID Number Station Assignment .............2-536 4-28 Multilingual LCD Indication Selection ............2-537 4-29 HFU Selection ..................2-538 4-30 Hold/Transfer Recall Display Selection ...........2-539 4-31 Receiving Internal/All Call Page Selection ..........2-540...
Page 22: Table Of Contents

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 4-62 ISDN-PRI Directory Number Selection ............2-580 4-64 Code Restriction Class (without Authorization Code) Day Mode Assignment ................2-582 4-65 Code Restriction Class (without Authorization Code) Night Mode Assignment ................2-584 4-66 MOH or Ring Back Tone Selection ............2-586 4-67 IP Station Number Assignment ...............2-588...
Page 23: Table Of Contents

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 7-3-03 MIF (UCD) Assignment ................2-639 7-3-04 MIF (Caller ID) Assignment ..............2-640 ROM Version Confirmation ..............2-641 System Speed Dial Memory Clear ............2-642 Station Speed Dial Memory Clear ............2-643 Second Initialization ................2-645 Clock/Calendar Setting ................2-646...
Page 24: Table Of Contents

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1.5.2 8-Digit Matching Tables with Default Values ........3-8 Code Restriction Algorithm ............3-12 Section 2 Automatic Route Selection ............... 3-15 General ..................3-15 Memory Blocks ................3-15 Memory Block Description ............. 3-16 2.3.1...
Page 25: Table Of Contents

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Section 3 ISDN-PRI Call by Call ................ 3-31 General ..................3-31 Memory Blocks ................3-31 Memory Block Description ............3-33 3.3.1 DID Digit Length Selection (Memory Block 1-1-20) ......3-33 3.3.2 DID Digit Conversion Assignment (Memory Block 1-1-21) ....3-33 3.3.3...
Page 26: Table Of Contents

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 3.3.22 Trunk Type Selection (Memory Block 3-91) ........3-36 3.3.23 Trunk (Installed, DP/DTMF) Selection (Memory Block 3-92) ..... 3-36 3.3.24 CO/PBX Ring Assignment (Day Mode) (Memory Block 4-01) ................. 3-36 3.3.25 CO/PBX Ring Assignment (Night Mode) (Memory Block 4-02) .................
Page 27: Table Of Contents

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 3.3.44 Call by Call Incoming Type Selection (Memory Block 1-10-22) ..............3-39 Call by Call (CBC) Programming (LCR PC Software V2.0 or Higher) ..........3-40 3.4.1 The International/Operator Table ............3-40 3.4.2 The OCC Table .................. 3-40 3.4.3...
Page 28: Table Of Contents

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Appendix A Function Time Chart Section 1 Time Chart ................... A-1 Appendix B Character Codes Section 1 Character Assignment ............... B-1 Character Code Tables ..............B-1 Dial Pad Character Assignment ............B-4 1.2.1 Trunk Name or Number Assignment Example ........
Page 29

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ THIS PAGE INTENTIONALLY LEFT BLANK ___________________________________________________________________________________ Table of Contents...
Page 30

LIST OF FIGURES ___________________________________________________________________________________ Figure 1-1 Programming Flowchart ..................1-2 Figure 1-2 Electra Elite IPK Multiline Terminal ..............1-6 Figure 1-3 Page Display for 8-Key, and 16-Key Multiline Terminals .........1-10 Figure 1-4 Page Switching for Data Values ..............1-11 Figure 3-1 Automatic Route Selection (ARS) System Data Flow ........3-20 Figure 3-2 Quality of Service Configuration ..............3-55...
Page 31

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ THIS PAGE INTENTIONALLY LEFT BLANK ___________________________________________________________________________________ xxii List of Figures...
Page 32

LIST OF TABLES ___________________________________________________________________________________ Table 1-1 Programming Modes ....................1-3 Table 1-2 Multiline Terminal Keys Used for Programming ............1-7 Table 2-1 Voice Mail AA-Info Settings ..................2-258 Table 2-2 Card Interface Slot Assignment ................2-631 Table 3-1 Automatic Route Selection to Route Number Assignment ........3-21 Table 3-2 Route Number to Trunk Group/RAB Selection and Digit Control ......
Page 33

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ THIS PAGE INTENTIONALLY LEFT BLANK ___________________________________________________________________________________ xxiv List of Tables...
Page 34

ENERAL NFORMATION A stored program controls the Electra Elite IPK system. When the system is initially powered up, the CPUI( )-U( ) ETU scans all interface and AP slots to determine the hardware configuration. The system stores this information and the default values in the resident system program memory.
Page 35: Features Of Programming

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ New Installation Existing System Develop System Component Function Data Sheet Replacement Change Installation Rewrite System Rewrite System Data Sheet Data Sheet Test System with Default Installation Values System Data System Data System Data...
Page 36: System Programming Modes

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Two Multiline Terminals, connected to ports 01 and 02, respectively, can be used simultaneously for programming. System Programming Modes Modes and submodes are listed in Table 1-1 Programming Modes. Table 1-1 Programming Modes...
Page 37: Section 2 Programming The System

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Table 1-1 Programming Modes (Continued) Line Line Mode Name Submode Name LK 1 ROM Version Confirmation LK 2 System Speed Dial Memory Clear LK 8 Special Mode LK 3 Station Speed Dial Memory Clear...
Page 38: Writing System Data

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Writing System Data After turning on power, the system data can be programmed using a Multiline Terminal connected to port 01 or port 02 (the Multiline Terminal must be idle). System programming can be performed while other Multiline Terminals in the system are in use.
Page 39: Programming Methods

Using the Multiline Terminal for Programming System programming can be performed using a Display Multiline Terminal that is connected to station port 01 or 02. Figure 1-2 Electra Elite IPK Multiline Terminal shows the terminal in the offline mode. Exit...
Page 40

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Table 1-2 Multiline Terminal Keys Used for Programming provides a list and description of the keys used during Multiline Terminal Programming. Table 1-2 Multiline Terminal Keys Used for Programming Description Used to enter data from the dial pad or to specify a Memory Block location.
Page 41: Entering Programming Mode

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Table 1-2 Multiline Terminal Keys Used for Programming Description This key is used to enter a pause, hyphen, asterisk or pound. To enter an asterisk or pound: The Message Waiting LED turns on and off after i s pressed.
Page 42: Page Switching

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Dial , and i n sequence. The Multiline Terminal LCD indicates program mode is now active. P R O G R A M M O D E T I M E D I S P L A Y While off-line, the programming terminal cannot be signaled by any system station.
Page 43

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 8-Key Multiline Terminal 8-Key Multiline Terminal DTH/DTR DTU/DTP LCD Display: 01 to indicate Page 1 LCD Display: Page 1 01 to indicate Page 1 Page 1 09 to indicate page 2 LK 1...
Page 44

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Figure 1-4 Page Switching for Data Values is an example of 10 data values. Values are displayed on two pages. 16-Key Multiline Terminal DTU/DTP (Page 1) LK 1 LK 2 LK 3 LK 4...
Page 45: Station Port Numbering Plan

Electra Elite IPK ___________________________________________________________________________________ 2.5.5 Station Port Numbering Plan Some Memory Blocks require entering a 2-digit port number. The Electra Elite IPK system supports 48/120 ports, respectively. Programming values for entry of Port Assignments are defined below: Port Assignments Programming Value...
Page 46: Section 3 System Data List

The System Data List is a complete list of Memory Blocks that are available in the Electra Elite IPK system. The information is organized by mode, submode, and then numerically by Memory Block number. The Memory Block number and name, the default values, and programming values are provided for each Memory Block.
Page 47

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ LK 1 System Mode LK 1 CO Line (Continued) Data Memory Block Name Default Value Programming Values Station Transfer/Camp-On Recall 45s (R2500 or lower) 25s, 45s, 60s, 90s, 120s, 180s, 240s, ∞ (No Limit) (R2500 or lower)
Page 48

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ LK 1 System Mode LK 1 CO Line (Continued) Data Memory Block Name Default Value Programming Values Speed Dial Buffer Allocation 100, 1,000 Memories Trunk Queuing Timeout Selection 10s (R2500 or lower) 10s, 20s, 30s, 60s (R2500 or lower)
Page 49

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ LK 1 System Mode LK 1 CO Line (Continued) Data Memory Block Name Default Value Programming Values Hold Recall Time Selection 1.0 (R2500 or lower) In minutes: 0.5, 1.0, 1.5, 2.0, 3.0, 5.0, 8.0, ∞ (No Limit) (R2500 or lower)
Page 50

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ LK 1 System Mode LK 1 CO Line (Continued) Data Memory Block Name Default Value Programming Values Delayed Ringing Time Assignment 00 ~ 99 sec. (CO) Caller ID Display Assignment for Not Specified...
Page 51: Section 1 Character Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ LK 1 System Mode LK 2 ICM (Continued) Data Memory Block Name Default Value Programming Values Specified Station Access Code 00 = 01 Tel. Port Number Assignment 01 ~ 23 Not Set 9~18...
Page 52

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ LK 1 System Mode LK 2 ICM (Continued) Data Memory Block Name Default Value Programming Values Expanded Station Number Blank (Not Specified) 2, 3, or 4 Digits Blank (Not Specified) Assignment 5-Digit 1~8, one digit...
Page 53

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ LK 1 System Mode LK 3 SLT (Continued) Data Memory Block Name Default Value Programming Values Voice Mail DTMF Duration/Interdigit 110/80 In milliseconds: 60/70, 110/80, 410/ Time Selection 100, 610/100, 810/190 SLT/PSII Talk Start timer...
Page 54

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ LK 1 System Mode LK 4 Transfer/Automated Attendant (A.A.) (Continued) Data Memory Block Name Default Value Programming Values Automated Attendant Message YS, NO Day/Night Mode Selection Automated Attendant Message to Tenant Number 00 to 47...
Page 55

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ LK 1 System Mode LK 5 SMDR/LCR Data Memory Block Name Default Value Programming Values SMDR Print Format ALL, MSK Printer Connected Selection NO, PC(Future), YS Printer Line Feed Control Selection YS, NO...
Page 56

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ LK 1 System Mode LK 7 ESP Data Memory Block Name Default Value Programming Values Doorphone Assignment No default LK1~LK4 Assigns DPH1~DPH4 Yes or Doorphone Display Time Selection 10s (R2500 or lower) 10s, 30s, 60s, 90s (R2500 or lower)
Page 57

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ LK 1 System Mode LK 8 PBR/Miscellaneous Data Memory Block Name Default Value Programming Values SLT or Automated Attendant/DISA LK1 and LK2 Off Off = Single Line Telephone to CPU PBR Selection On = Automated Attendant/DISA PBR Receive Level Assignment for 03 (–36.0 dBm)
Page 58

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ LK 1 System Mode LK 8 PBR/Miscellaneous (Continued) Data Memory Block Name Default Value Programming Values Voice Mail Quick Transfer Master Station numbers: Hunt Number 2-digit 10-89 3-digit 100-899 4-digit 1000-8999 5-digit 10000-89999...
Page 59

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ LK 1 System Mode LK 8 PBR/Miscellaneous (Continued) Data Memory Block Name Default Value Programming Values Enhanced 911 Alternate Route No Alternate Route Assignment (Maintenance Busy) 101~132 for Trunk Group 01~32 201~216 for Route Advance Block...
Page 60

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ LK 1 System Mode LK 10 Call by Call Data Memory Block Name Default Value Programming Values Call by Call Type of Network ID All RABs 2 Not Used) Assignment National Network Identification...
Page 61

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ LK 1 System Mode LK 10 Call by Call (Continued) Data Memory Block Name Default Value Programming Values Call by Call Facility Coding Value All RABs 00 Non-CBC RAB, None Assignment (Feature) 5ESS Local Exchange...
Page 62

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ LK 1 System Mode LK 11 DTI Data Memory Block Name Default Value Programming Values T1 Signal Format Selection 12 (Superframe), 24 (Extended Superframe) Clear Channel Selection ZCS, B8ZS Line Length Selection Refer to...
Page 63

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ LK 1 System Mode LK 13 PRT Data Memory Block Name Default Value Programming Values PRT Channel Assignment 0, 4, 8, 12, 16, 20, 24 PRT Signal Format Selection 12 (SF), 24 (ESF)
Page 64

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ LK 1 System Mode LK 15 K-CCIS Data Memory Block Name Default Value Programming Values K-CCIS Main/Remote Office NONE NONE, MAIN, REMOTE Selection Common Signal Channel Data 64k, 56k, 48k(1), 48k(2) Speed Assignment...
Page 65

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ LK 1 System Mode LK 15 K-CCIS (Continued) Data Memory Block Name Default Value Programming Values Centralized BLF Send Extension All Tables Not Table Range: 001~120 Number Assignment Specified 3-digit Extension numbers 100~899...
Page 66

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ LK 1 System Mode LK 16 HUB (Continued) Data Memory Block Name Default Value Programming Values High Priority TX Tag Assignment (Lowest) 0~7 (Highest) Low Priority TX Tag Assignment (Lowest) 0~7 (Highest) Port Mirroring Selection...
Page 67

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ LK 3 CO/PBX Line Mode Data Memory Block Name Default Value Programming Values Trunk Name/Number Assignment Not Specified Maximum of 13 digits (numbers, hyphens, and spaces) Trunk Status Selection OUT&IN OUT&IN, IN Trunk-to-Trunk Group Assignment...
Page 68

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ LK 3 CO/PBX Line Mode (Continued) Data Memory Block Name Default Value Programming Values Tie Line/CO/PBX Incoming Signal Refer to 3-19 Tie Line/CO/PBX Detect Time Selection Incoming Signal Detect Time Selection on page 2-444.
Page 69

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ LK 3 CO/PBX Line Mode (Continued) Data Memory Block Name Default Value Programming Values Automatic Release Signal Detection In milliseconds: Selection 0, 50, 100, 150, 200, 250, 300, 350, 400, 450, 500, 550, 600, 650, 700, ∞ (No...
Page 70

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ LK 3 CO/PBX Line Mode (Continued) Data Memory Block Name Default Value Programming Values CO Message Waiting Yes/No NO, YES Selection Polarity Reverse Selection NO, YS Trunk Type Selection CO, PBX, TIE, DID, CTX (Assume-9)
Page 71

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ LK 4 Telephone Mode (Continued) Data Memory Block Name Default Value Programming Values Telephone to Tenant Assignment 00 (All Tenant Tenant Number Telephones) Station Number Assignment Refer to 4-10 Station Number Assignment on page 2-513.
Page 72

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ LK 4 Telephone Mode (Continued) Data Memory Block Name Default Value Programming Values Trunk Digit Restriction 00 (No Limit) 00~99 Voice Mail/SLT Selection NO, YS Voice Prompt Selection NO, YS Extension Line Key Ring...
Page 73

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ LK 4 Telephone Mode (Continued) Data Memory Block Name Default Value Programming Values CO/PBX Answer Key Operation NO, YS Without Ringing Assignment (Night Mode) Enhanced 911 CESID to Station Not Specified 7 or 10 digits plus up to 5-digit...
Page 74

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ LK 4 Telephone Mode (Continued) Data Memory Block Name Default Value Programming Values Internal Zone Paging Selection No, A, B, C 3-Minute Alarm Selection NO, YS DTMF/DP SLT Type Selection DP, MF LK 5 Trunk Group Mode...
Page 75

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ LK 6 Copy Mode Data Memory Block Name Default Value Programming Values Tenant Mode Copy Assignment CO Line Mode Copy Assignment Telephone Mode Copy Assignment Trunk Group Mode Copy Assignment ___________________________________________________________________________________ 1 - 42...
Page 76

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ LK 7 ETU Mode Data Memory Block Name Default Value Programming Values Card Interface Slot Assignment Refer to 7-1 Card Interface Slot Assignment on page 2-627. Telephone Type Assignment NON, TEL, DSS CONSOL, SLT ADP,...
Page 77

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ THIS PAGE INTENTIONALLY LEFT BLANK ___________________________________________________________________________________ 1 - 44 Multiline Terminal Programming...
Page 78

Memory Blocks Chapter 2 ___________________________________________________________________________________ ECTION ROGRAMMING YSTEM SING THE EMORY LOCK This section provides detailed instructions for programming individual Memory Blocks. The Memory Blocks are listed numerically. For each Memory Block, the following information is provided. General Description is a brief explanation of the function of the Memory Block.
Page 79: Pause Time Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-1-00 Pause Time Selection System Mode General Description Submode Use this Memory Block to specify the pause time that can be inserted between digits dialed on CO/PBX and Tie lines. Data No. Display...
Page 80: Dp Interdigit Time Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-01 DP Interdigit Time Selection System Mode General Description Submode The DP Interdigit Time is the minimum pause time between Dial Pulses. Use this Memory Block to Select Pattern A or Pattern B.
Page 81: Hookflash Time Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-1-02 Hookflash Time Selection System Mode General Description Submode Use this Memory Block to specify the loop open time for a hookflash signal sent to the CO or PBX when the Recall key on a Multiline Terminal is pressed. A Single Line Telephone (SLT) generates a hookflash to the CO or PBX line when a Single Line Data No.
Page 82

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-1-46 Access Code (1-Digit) Assignment 1-1-47 Access Code (2-Digit) Assignment 1-3-02 SLT Hookflash Signal Selection 4-24 SLT Hookflash Assignment Notes A 1- or 2-digit Access Code can be assigned in Memory Block 1-1-46/47 [Access Code (1- or 2-Digit) Assignment] for Single Line Telephones to send a hookflash signal on a CO/PBX line (default: 6 #).
Page 83: Hold Recall Time Selection (non-exclusive Hold)

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-1-03 Hold Recall Time Selection System Mode (Non-Exclusive Hold) Submode General Description Use this Memory Block to specify the Hold time for a Non-Exclusive outside call Data No. before a recall tone is generated. When No Limit is selected, the hold recall alarm tone is not generated.
Page 84

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Display (R3000 or higher) T i m e r C l a s s D a t a S e t t i n g 1 ~ 4 T i t l e N o .
Page 85: Automatic Redial Time Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-1-04 Automatic Redial Time Selection System Mode General Description Submode When a called party is busy, the station user dials an Access Code and restores the handset. Use this Memory Block to define the redial timing parameters when automatic redial is set to a busy CO/PBX number.
Page 86: Start Time Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-05 Start Time Selection System Mode General Description Submode Use this Memory Block to specify the time after dialing before the system starts the Elapsed Call Time. Used for copper trunks only. Not supported by digital trunks.
Page 87

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Display (R3000 or higher) T i m e r C l a s s D a t a S e t t i n g 1 ~ 4 T i t l e N o .
Page 88: Co/pbx Incoming Ringing Alarm Time Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-06 CO/PBX Incoming Ringing Alarm System Mode Time Selection Submode General Description Use this Memory Block to specify the time between when a CO/PBX call is detected Data No. and the ringing tone changes to a higher pitch when the call is not answered. When No Limit is selected, the ringing tone does not change.
Page 89

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Display (R3000 or higher) S e t t i n g D a t a D a t a N o . T i t l e 0 6 : R I N G...
Page 90: Tie Line Delay Ringing Time Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-07 Tie Line Delay Ringing Time System Mode Selection Submode General Description Use this Memory Block to specify the time before a Tie line call ringing at a station can Data No. begin ringing at other preassigned stations when it is not answered in a programmed time.
Page 91

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Display (R3000 or higher) T i m e r C l a s s D a t a S e t t i n g 1 ~ 4 N o . T i t l e...
Page 92

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Notes Example: ¤ System 1 System 2 ¤ ¤ Electra Elite (A) 100 Electra Elite Electra Elite (C) 102 System I Elite IPK IPK System II ¤ ¤ System I (B) 101 (B) 101 ¤...
Page 93: Manual Pause Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-1-09 Manual Pause Selection System Mode General Description Submode Use this Memory Block to specify either YS (Pause Insertion) or NO (Last Number Dialed/Speed Dial) to be executed using the Redial key when it is pressed after one or more digits of a dialed number are entered.
Page 94

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Notes When a user seizes a CO/PBX line and dials 907 4000 + + 12345 with this Memory Block set to NO, the system interprets the sequence as: 9074000XXX345 (XXX = and 12 is interpreted as Speed Dial buffer 12).
Page 95: System Transfer/camp-on Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-1-11 System Transfer/Camp-On Selection System Mode General Description Submode Use this Memory Block system-wide to select whether or not the station user can press the Transfer key to perform a Ring Transfer or Station Camp-On.
Page 96: Station Transfer/camp-on Recall Time Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-12 Station Transfer/Camp-On Recall System Mode Time Selection Submode General Description Use this Memory Block to specify the time before a Ring Transfer or Station Camp-On Data No. from a station (without an Attendant Add-On Console) recalls back to the originating station when the call is not answered.
Page 97

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Display (R3000 or higher) T i m e r C l a s s D a t a S e t t i n g 1 ~ 4 N o . T i t l e...
Page 98: Co Transfer Ring Pattern Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-13 CO Transfer Ring Pattern Selection System Mode General Description Submode Use this Memory Block to select a Ring Pattern for CO transfers. Display Data No. S e t t i n g...
Page 99

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ The Ring Patterns are shown in the table below: s= seconds Line Pattern Tone LK 1 Tone LK 2 LK 3 LK 4 LK 5 LK 6 LK 7 LK 8 LK 1 (Pg.
Page 100: Co Transfer Ring Tone Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-14 CO Transfer Ring Tone Selection System Mode General Description Submode Use this Memory Block to select a ring tone for CO transfers. Display Data No. S e t t i n g...
Page 101: System Speed Dial Restriction By Tenant

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-1-18 System Speed Dial Restriction by System Mode Tenant Submode General Description Use this Memory Block to specify whether or not System Speed Dial is restricted for Data No. each tenant. Display PC Programming...
Page 102

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Programming Procedures 3 Press the corresponding CO/PBX line key to change the tenant number. Default Values Speed Dial buffers have the nine groups listed in the table below. All System Speed Dial buffers can be dialed from any tenant.
Page 103

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Notes One or more tenants can be enabled to use each group. Use this Memory Block to assign which tenants use each group. When speed dial is set to 1000, 900~999 cannot be restricted.
Page 104: Did Digit Length Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-20 DID Digit Length Selection System Mode General Description Submode Use this Memory Block to define the number of Direct Inward Dialing (DID) digits in Memory Block 1-1-22 (DID Digit Conversion Table). Data No.
Page 105: Did Digit Conversion Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-1-21 DID Digit Conversion Assignment System Mode General Description Submode Use this Memory Block to enable the DID Digit Conversion Table, Memory Block 1-1-22 (DID Digit Conversion Table), for each number. Data No.
Page 106: Did Digit Conversion Table

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-22 DID Digit Conversion Table System Mode General Description Submode Up to 200 incoming DID numbers can be assigned individually to ring at a preassigned 2-digit, 3-digit, or 4-digit station number, closed number (plus outgoing digits), or tenant number (00~47) for day mode or night mode.
Page 107

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Programming Procedures (Continued) 4 Press to write the data and display the next Memory Block. 5 Program the next Memory Block or press to go back on-line. Related Programming M.B. Number Memory Block Name...
Page 108: Did Forward Station Number For Busy Station Or Undefined Digit

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-23 DID Forward Station Number for System Mode Busy Station or Undefined Digit Submode General Description Use this Memory Block when Memory Block 1-1-22 (DID Digit Conversion Table) is Data No. enabled to define where digits are routed when undefined or the station is busy.
Page 109

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Notes When this Memory Block is set to a Tenant, the following must be assigned to ring the desired station: Memory Block 4-01 [CO/PBX Ring Assignment (Day Mode)] Memory Block 4-02 [CO/PBX Ring Assignment (Night Mode)] Memory Block 4-09 (Telephone to Tenant Assignment).
Page 110: Pbx/ctx Access Code Assignment I

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-24 PBX/CTX Access Code Assignment I System Mode General Description Submode Use this Memory Block to specify a PBX line PBX/CTX Access Code together with pauses for outgoing calls. Data No. Display S e t t i n g...
Page 111

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Notes ¤ Example: Elite IPK System Elite IPK System PBX Line CO Line Intercom Line Features such as Code Restriction do not operate properly unless a PBX/CTX Access Code is specified. This limitation applies to PBX lines assigned in Memory Block 3-91 (Trunk Type Selection).
Page 112: Pbx/ctx Access Code Assignment Ii

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-25 PBX/CTX Access Code Assignment II System Mode General Description Submode Use this Memory Block to specify a second PBX line PBX/CTX Access Code together with pauses for outgoing calls. Data No. Display...
Page 113

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Notes ¤ Example: Elite IPK System Elite IPK System Intercom Line PBX Line Tie Line Features such as Code Restriction do not operate properly unless a PBX/CTX Access Code is specified. This limitation only applies to PBX lines assigned in Memory Block 3-91 (Trunk Type Selection).
Page 114: Automatic Day/night Mode Switching Time Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-27 Automatic Day/Night Mode Switching System Mode Time Assignment Submode General Description Use this Memory Block to assign a start time for Pattern 1 and a different start time for Data No. Pattern 2 to automatically switch between Day Mode and Night Mode.
Page 115

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming (Continued) M.B. Number Memory Block Name 4-17 Station to Class of Service Feature Assignment 4-37 Extension Line Key Ring Assignment (Day Mode) 4-38 Extension Line Key Ring Assignment (Night Mode) Notes The start time for Day Mode or Night Mode can be programmed to automatically switch modes at the specified times.
Page 116: Distinctive Ringing By Telephone Or Co Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-28 Distinctive Ringing by Telephone or System Mode CO Selection Submode General Description Use this Memory Block to assign a distinctive ringing tone for each telephone or each Data No. CO/PBX line. Display...
Page 117: Private Line Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-1-29 Private Line Assignment System Mode General Description Submode Use this Memory Block to assign an outside line as a private line. The private line cannot be seized by any other telephone, and an LED indication is not provided to other terminals.
Page 118: Route Advance Block Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-30 Route Advance Block Assignment System Mode General Description Submode Use this Memory Block to assign a priority level (1~4) to each Trunk group assigned in a Route Advance Block. The system has 32 blocks that can be specified.
Page 119

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 3-03 Trunk-to-Trunk Group Assignment Notes When 00 (Not Set) is programmed, no trunks are accessed for this priority setting. When Route Advance Block Numbers are assigned and a line key is pressed or an Access Code is dialed, the system starts searching for an idle line in a specified group (beginning with the Trunk group assigned priority 1).
Page 120: Automatic Day/night Mode By Day Of Week Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-32 Automatic Day/Night Mode by Day of System Mode Week Selection Submode General Description Use this Memory Block to select either Pattern 1 or Pattern 2 Day/Night Mode start Data No. time for each day of the week. Memory Block 1-1-27 (Automatic Day/Night Mode Switching Time Assignment) sets Day/Night Mode start time for Pattern 1 and Pattern 2 to switch the system between Day Mode and Night Mode.
Page 121

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-1-27 Automatic Day/Night Mode Switching Time Assignment 1-8-07 Class of Service (Attendant) Feature Selection 1 1-8-48 Automatic Daylight Saving Time Selection 4-09 Telephone to Tenant Assignment...
Page 122: Speed Dial Number/name Display Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-33 Speed Dial Number/Name Display System Mode Selection Submode General Description Use this Memory Block to specify whether the dialed number or name is displayed first Data No. on the LCD of the originating station when an outgoing call is made using Speed Dial.
Page 123: Tie Line First Ring Pattern Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-1-34 Tie Line First Ring Pattern Selection System Mode General Description Submode Use this Memory Block to set a specific ringing pattern for incoming calls on Tie lines. After a delay interval specified in Memory Block 1-1-07 (Tie Line Delay Ringing Time Selection), a Tie call can ring at all Day/Night ring-assigned telephones using a Data No.
Page 124

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Ringing Pattern Selection s= seconds Pattern Same as Internal Ring Voice Announce ___________________________________________________________________________________ Programming Manual 2 - 47...
Page 125: Speed Dial Buffer Allocation

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-1-35 Speed Dial Buffer Allocation System Mode General Description Submode Use this Memory Block to specify either 100-memory or 1000-memory allocation. Display Data No. S e t t i n g D a t a...
Page 126: Trunk Queuing Timeout Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-37 Trunk Queuing Timeout Selection System Mode General Description Submode Use this Memory Block to specify the time that a station with Trunk Queue set rings, before the queue is automatically canceled. Data No.
Page 127

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Display (R3000 or higher) T i m e r C l a s s D a t a S e t t i n g 1 ~ 4 N o . T i t l e...
Page 128: Access Code (1-digit) Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-46 Access Code (1-Digit) Assignment System Mode General Description Submode Use this Memory Block to assign a 1-digit number as an Access Code or station number. Data No. Display D i a l N o .
Page 129

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Notes Select options from the list of function numbers in Memory Block 1-1-46 [Access Code (1-Digit) Assignment], and assign a number (from 0~9), , or to each selected function. When a function is assigned a 1-digit Access Code, 2-digit Access Codes with the same first digit become invalid (i.e., if a function is assigned to Access Code 5, Access Codes 50~59, 5 , and 5...
Page 130

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ This table applies to Data Numbers 46, 47, and 48. Default Function Default Function Function Name Function Name Dial No. Dial No. 4, 5, 6, 7 Not Used Call Forward – All Call Cancel from...
Page 131

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ This table applies to Data Numbers 46, 47, and 48. Default Function Default Function Function Name Function Name Dial No. Dial No. 4, 5, 6, 7 Not Used Call Forward – All Call Cancel from...
Page 132

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Default Function Default Function Function Name Function Name Dial No. Dial No. Call Pickup CO/PBX by Tenant All External Zone Paging (1-digit) External Zone A Paging Call Pickup CO/PBX/Centrex by External Zone B Paging...
Page 133

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Default Function Default Function Function Name Function Name Dial No. Dial No. Trunk Group 01 Call Forward – Busy/ No Answer Split Cancel Trunk Group 02 Call Forward – All Split Set Trunk Group 03 Call Forward –...
Page 134

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Default Function Default Function Function Name Function Name Dial No. Dial No. Specified Station Access Code Closed Number Block 1 Specified Station Access Code Specified Station Access Code Closed Number Block 16 Not Used...
Page 135: Access Code (2-digit) Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-1-47 Access Code (2-Digit) Assignment System Mode General Description Submode Use this Memory Block to assign a 2-digit number as an Access Code. Display Data No. D i a l N o .
Page 136

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Notes Select options from the list of function numbers in Memory Block 1-1-46 [Access Code (1-Digit) Assignment], and assign a number (from 00~99), , or to each selected function. When a function is assigned a 1-digit Access Code, 2-digit Access Codes with the same first digit become invalid (i.e., if a function is assigned to Access Code 5, Access Codes 50~59, 5 , and 5...
Page 137: Access Code (3-digit) Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-1-48 Access Code (3-Digit) Assignment System Mode General Description Submode Use this Memory Block to assign a 3-digit number as an Access Code. With System Software R2500, Function 001 (Station Number) can be assigned Data No.
Page 138

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-1-46 Access Code (1-Digit) Assignment 1-1-47 Access Code (2-Digit) Assignment 1-2-03 2~7-Digit Station Number Selection 1-2-34 Expanded Station Number Assignment ___________________________________________________________________________________ Programming Manual 2 - 61...
Page 139

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Notes Select options from the list of function numbers in Memory Block 1-1-46 [Access Code (1-Digit) Assignment], and assign a 3-digit Access Code. When a function is assigned a 1-digit Access Code or 2-digit Access Code, 3-digit Access Codes (with the same first digit) become invalid (i.e., if a function is assigned to Access Code 5, Access Codes 50~59, 5 ,...
Page 140

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Notes (Continued) 7-Digit Station Numbers MB 1-2-03 (2~7-Digit Station Number Selection) 7DGT MB 1-2-34 (Expanded Station Number Assignment) MB 1-1-47 [Access Code (2-Digit ) Assignment] (AC20 301 (Digit Table 01) MB 1-1-48 [Access Code (3-Digit ) Assignment]...
Page 141: Networking Trunk Group/route Advance Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-1-49 Networking Trunk Group/Route System Mode Advance Assignment Submode General Description Use this Memory Block to assign the function number of the Trunk Group to be used to Data No. network an Electra Elite 48/192 system to another system by Tie lines or CO/PBX/ CTX lines.
Page 142: Co/pbx Outgoing Digit Add Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-50 CO/PBX Outgoing Digit Add System Mode Assignment Submode General Description Use this Memory Block to specify up to 10 additional digits when a trunk in the Trunk Data No. group or Route Advance block assigned in Memory Block 1-1-49 (Networking Trunk Group/Route Advance Assignment) is seized, and a number is dialed.
Page 143

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Notes Example: Station 100 Add 200 Dials 200 ¤ System System ¤ Station 200 Rings To assign System 1 in System Programming: Memory Block 1-1-46 [Access Code (1-Digit) assignment]. Assignment 2 → 401 (Closed Number Block 01).
Page 144: Co Line Ringing Pattern Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-51 CO Line Ringing Pattern Selection System Mode General Description Submode Use this Memory Block to assign the initial ringing pattern or no ring for incoming calls on a CO line. Data No.
Page 145

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ The Ring Patterns are shown in the table below: s= seconds Pattern No Ring ___________________________________________________________________________________ 2 - 68 Memory Blocks...
Page 146: Pbx Line Ringing Pattern Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-52 PBX Line Ringing Pattern Selection System Mode General Description Submode Use this Memory Block to assign the initial ringing pattern or no ring for incoming calls on a PBX line. Data No.
Page 147

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ The Ring Patterns are listed in the table below: s= seconds Pattern No Ring ___________________________________________________________________________________ 2 - 70 Memory Blocks...
Page 148: Tie Line Delay Ring Pattern Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-53 Tie Line Delay Ring Pattern Selection System Mode General Description Submode Use this Memory Block to select a ringing pattern or no ring for incoming calls on a Tie line after the timeout set in Memory Block 1-1-07 (Tie Line Delay Ringing Time Selection).
Page 149

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-1-07 Tie Line Delay Ringing Time Selection 1-1-34 Tie Line First Ring Pattern Selection 4-01 CO/PBX Ring Assignment (Day Mode) 4-02 CO/PBX Ring Assignment (Night Mode)
Page 150: Automated Attendant Transfer Ring Pattern

Memory Block. 5 Program the next Memory Block or press to go back on-line. Related Programming Refer to individual features in the Electra Elite IPK Features and Specifications Manual. ___________________________________________________________________________________ Programming Manual 2 - 73...
Page 151

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ The Ring Patterns are shown in the table below: s= seconds Pattern No Ring ___________________________________________________________________________________ 2 - 74 Memory Blocks...
Page 152: Did Line Ringing Pattern Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-55 DID Line Ringing Pattern Selection System Mode General Description Submode Use this Memory Block to assign the ringing pattern or no ring to be used for DID calls. Display Data No. D a t a...
Page 153: Co/pbx Prepause Time Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-1-57 CO/PBX Prepause Time Selection System Mode General Description Submode Use this Memory Block to assign a pause time before dialed digits can be sent over a CO/PBX line after the trunk is seized by a system user.
Page 154: Synchronous Ringing Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-59 Synchronous Ringing Selection System Mode General Description Submode Use this Memory Block to specify whether or not CO/PBX calls follow Synchronous Ringing. Data No. Display D a t a S e t t i n g...
Page 155: Digit Matching Table Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-1-60 8-Digit Matching Table Assignment System Mode General Description Submode Use this Memory Block to assign the outgoing dial digit for Code Restriction (except OCC Dial Digit - Normal Dial). Program this assignment in one of two ways: Data No.
Page 156

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Programming Procedures Operation data includes: Operation Dial Number Operation Data a nd 5 Press to write the data and advance to the next Dial Code. After all Dial Codes for 8-Digit Matching Table 00 are entered, press again to display 8 Digit Matching Table 01.
Page 157: Digit Matching Table To Class Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-1-61 8-Digit Matching Table to Class System Mode Assignment Submode General Description Use this Memory Block to program each 8-digit Matching Table to allow or deny Data No. assignment per class. Classes 00 and 15 are fixed. Only classes 01 14 can be programmed.
Page 158

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Table 00 Class YS = Allow NO = Deny NON = Blank ___________________________________________________________________________________ Programming Manual 2 - 81...
Page 159: System Speed Dial Override By Class Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-1-62 System Speed Dial Override by Class System Mode Selection Submode General Description Use this Memory Block to specify per Class whether or not Class Selection can Data No. override System Speed Dial.
Page 160: Hold Recall Time Selection (exclusive)

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-63 Hold Recall Time Selection System Mode (Exclusive) Submode General Description Use this Memory Block to specify the time for Exclusive Hold Recall. When No Limit is Data No. selected, Exclusive Hold Recall is not provided.
Page 161

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Display (R3000 or higher) T i m e r C l a s s D a t a S e t t i n g 1 ~ 4 N o . T i t l e...
Page 162: Code Restriction Class Allow/deny Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-65 Code Restriction Class Allow/Deny System Mode Selection Submode General Description Use this Memory Block to assign Code Restriction Classes as Allow or Deny. Data No. 0 1 ~ 1 4 This assignment is used when there is no match or there is an overlap (duplicate numbers in tables with opposite assignments) of numbers in the 8-Digit Matching Tables.
Page 163: Digit Matching Table To Normal Dial Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-1-66 8-Digit Matching Table to Normal System Mode Dial Assignment Submode General Description Use this Memory Block to assign the 8-Digit Matching Table by class for normal dialing Data No. as used or unused. When unused is assigned, the system does not check during normal dialing even when Memory Block 1-1-61 (8-Digit Matching Table to Class Assignment) is programmed.
Page 164: Occ Table Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-67 OCC Table Assignment System Mode General Description Submode Use this Memory Block to assign an Other Common Carrier (OCC) code (8-digit maximum) in a table. A maximum of 16 codes can be assigned.
Page 165: Digit Matching Table To Occ Table Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-1-68 8-Digit Matching Table to OCC Table System Mode Assignment Submode General Description Use this Memory Block to assign each 8-Digit Matching Table to each Other Common Data No. Carrier (OCC) Code Table.
Page 166: Tie Line Code Restriction Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-69 Tie Line Code Restriction Assignment System Mode General Description Submode Use this Memory Block to restrict outgoing Tie line dialed digits. Display Data No. D a t a S e t t i n g T i t l e N o .
Page 167: Code Restriction Class Assignment When Lockout Is Set

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-1-70 Code Restriction Class Assignment System Mode When Lockout is Set Submode General Description Use this Memory Block to assign the Code Restriction Class when a station user sets Data No. the Station Outgoing Lockout or when the Attendant sets Attendant Station Outgoing Lockout.
Page 168: First Delay Announcement Start Time Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-71 First Delay Announcement Start Time System Mode Selection Submode General Description Use this Memory Block to specify the time between receiving a CO call and sending a Data No. First Delay Announcement to the calling party.
Page 169: First Delay Announcement Repeat Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-1-72 First Delay Announcement Repeat System Mode Selection Submode General Description Use this Memory Block to specify the number of times a First Delay Announcement is Data No. repeated. Display PC Programming D a t a S e t t i n g N o .
Page 170: First To Second Delay Announcement Interval Time Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-73 First to Second Delay Announcement System Mode Interval Time Selection Submode General Description Use this Memory Block to specify the time between the end of the First Delay Data No. Announcement sending time and the start time of the Second Delay Announcement.
Page 171: Second Delay Announcement Repeat Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-1-74 Second Delay Announcement Repeat System Mode Selection Submode General Description Use this Memory Block to specify the number of times a Second Delay Announcement Data No. is repeated. Display PC Programming D a t a S e t t i n g N o .
Page 172: Second Delay Announcement Repeat Interval Time Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-75 Second Delay Announcement Repeat System Mode Interval Time Selection Submode General Description Use this Memory Block to specify the interval time to repeat Second Delay Data No. Announcement to the calling party.
Page 173: Barge-in Alert Tone Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-1-76 Barge-In Alert Tone Assignment System Mode General Description Submode Use this Memory Block to specify whether or not Barge-In Alert Tone is allowed. Display Data No. S e t t i n g...
Page 174: Delayed Ringing Time Assignment (co)

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-77 Delayed Ringing Time Assignment System Mode (CO) Submode General Description Use this Memory Block to assign the delayed ringing time for incoming outside line Data No. calls. Display PC Programming +BCM D a t a S e t t i n g N o .
Page 175: Caller Id Display Assignment For System Mode

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-1-78 Caller ID Display Assignment for System Mode System Mode Submode General Description Use this Memory Block to assign up to 15 Multiline Terminals to display ANI/Caller ID Data No. Indication for normal incoming CO/PBX calls or CO/PBX calls ringing a Call Arrival (CAR) key.
Page 176: Bgm Port Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-79 BGM Port Assignment System Mode General Description Submode Use this Memory Block to assign the CO/PBX port as a Background Music port. Display Data No. D a t a C O N o .
Page 177: Isdn Dtmf Duration/interdigit Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-1-80 ISDN DTMF Duration/Interdigit System Mode Selection Submode General Description Use this Memory Block to specify tone duration/interdigit time of Dual-Tone Data No. Multifrequency (DTMF) signals for the ISDN trunk. Display PC Programming...
Page 178: Isdn Dial Interval Time Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-81 ISDN Dial Interval Time Selection System Mode General Description Submode Use this Memory Block to specify the time between each digit dialed before digits are sent over the ISDN PRI line Network. This also applies to K-CCIS outgoing calls.
Page 179

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Display (3000 or higher) S e t t i n g D a t a D a t a N o . T i t l e 8 1 : I S D N...
Page 180: Co Feature Code Service For Code Restriction

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-1-82 CO Feature Code Service for Code System Mode Restriction Submode General Description Use this Memory Block to define a code to send to the CO in front of the dialed Data No.
Page 181: Call Monitoring Alert Tone Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-1-86 Call Monitoring Alert Tone System Mode Assignment Submode General Description Use this Memory Block to specify whether or not Call Monitoring Alert Tone is allowed. Data No. When allowed, the Conference LED indicates Call Monitoring. When denied, the Conference LED does not indicate Call Monitoring.
Page 182: Internal Paging Timeout Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-2-00 Internal Paging Timeout Selection System Mode General Description Submode Use this Memory Block to specify the time allowed for paging. This Memory Block can be adjusted in 1-second intervals (R3000 or higher).
Page 183

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Display (R3000 or higher) T i m e r C l a s s D a t a S e t t i n g 1 ~ 4 N o . T i t l e...
Page 184: Intercom Call Voice/tone Signal Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-2-01 Intercom Call Voice/Tone Signal System Mode Selection Submode General Description Use this Memory Block to specify whether signal tone or voice is used first for an Data No. intercom call. Display PC Programming...
Page 185: Automatic Callback Release Time Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-2-02 Automatic Callback Release Time System Mode Selection Submode General Description Use this Memory Block to specify the time allowed for an automatic callback before Data No. the request is automatically canceled. This Memory Block can be adjusted in 1-minute intervals (R3000 or higher).
Page 186

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Display (R3000 or higher) T i m e r C l a s s D a t a S e t t i n g 1 ~ 4 N o . T i t l e...
Page 187: Digit Station Number Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-2-03 2~7-Digit Station Number Selection System Mode General Description Submode Use this Memory Block to determine the number of digits for station numbers. Either 2-digit (10~89), 3-digit (100~899), or 4-digit (1000~8999) assignment is available or a 5-, 6-, or 7-digit station numbering plan is available.
Page 188

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Notes The Station Numbering Plan can be 2-~7- digits; however, only one plan can be used at a time. After a change is made in this Memory Block, all station numbers must be reassigned in Memory Block 4-10 (Station Number Assignment).
Page 189: Call Arrival Key Block Assignment

Memory Block. 5 Program the next Memory Block or press to go back on-line. Related Programming Refer to individual features in the Electra Elite IPK Features and Specifications Manual. ___________________________________________________________________________________ 2 - 112 Memory Blocks...
Page 190

Notes The Electra Elite IPK expanded system allows a maximum of 120 ports to be shared by station ports (ESI, SLI, FMS/VMS, and OPX) and Call Arrival Keys. When 32 station ports are being used, 88 remain for use as Call Arrival (CAR) Keys.
Page 191: Specified Station Access Code Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-2-08 Specified Station Access Code System Mode Assignment Submode General Description Use this Memory Block to assign specific stations for abbreviated dialing. Up to 24 Data No. stations can be assigned. Display PC Programming...
Page 192

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Notes Specified stations can be accessed from intercom (ICM) dial tone or as an outside caller calling into the Electra Elite IPK system Auto Attendant. The Specified Access Code is assigned in Memory Blocks 1-1-46 or 1-1-47 [Access Code (1-Digit/2-Digit) Assignment].
Page 193: Customized Message 1~10 Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-2-09~18 Customized Message 1~10 System Mode Assignment Submode General Description Use this Memory Block to program various messages for display at a station LCD. Data No. When a user places an intercom (ICM) call from a station equipped with an LCD...
Page 194: Intercom Ring Pattern Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-2-19 Intercom Ring Pattern Selection System Mode General Description Submode Use this Memory Block to select a ring pattern or turn the tone ON/OFF when intercom calls are made. Data No. Display S e t t i n g...
Page 195

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ The Ring Patterns are listed in the table below: s= seconds Line Pattern LK 1 LK 2 LK 3 LK 4 LK 5 LK 6 LK 7 LK 8 LK 1 (Pg. 2) LK 2 (Pg.
Page 196: Intercom Ring Tone Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-2-20 Intercom Ring Tone Selection System Mode General Description Submode Use this Memory Block to select a ring tone for intercom calls. Display Data No. S e t t i n g D a t a T i t l e N o .
Page 197: Ps Telephone Block Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-2-21 PS Telephone Block Assignment System Mode General Description Submode Use this Memory Block to specify the number of PS II stations that can be used in the system. Data No. Display D a t a...
Page 198

The Electra Elite IPK expanded system can support a maximum of 40 PS II stations. The Electra Elite IPK basic system can have 32 ports to be shared by station ports (ESI, SLI, FMS/VMS, CNF, and OPX), Call Arrival Keys, and PS stations. If 24 station ports are being used, eight remain for use as PS stations.
Page 199: Call Forward - No Answer Time Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-2-22 Call Forward - No Answer Time System Mode Selection Submode General Description Use this Memory Block to specify the time before incoming intercom calls or incoming Data No. CO/PBX lines are forwarded to another station number when the called party does not answer.
Page 200

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Display (R3000 or higher) T i m e r C l a s s D a t a S e t t i n g 1 ~ 4 N o . T i t l e...
Page 201: System Call Park Recall Time Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-2-23 System Call Park Recall Time System Mode Selection Submode General Description Use this Memory Block to specify the time before a CO/PBX call recalls back to a Data No. station from Call Park.
Page 202

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Display (R3000 or higher) T i m e r C l a s s D a t a S e t t i n g 1 ~ 4 N o . T i t l e...
Page 203: Intercom Feature Access Code Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-2-24 Intercom Feature Access Code System Mode Assignment Submode General Description Use this Memory Block to assign the Access Code for Voice/Tone change or Step Data No. Call. Display PC Programming S e t t i n g...
Page 204

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-2-01 Intercom Call Voice/Tone Signal Selection 1-8-08 Class of Service (Station) Feature Selection 2 1-8-26 Voice Mail Quick Transfer Master Hunt Number 4-17 Station to Class of Service Feature Assignment Notes Features can be assigned to more than one dial number.
Page 205: Internal Paging Alert Tone Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-2-25 Internal Paging Alert Tone Selection System Mode General Description Submode Use this Memory Block to specify whether or not a call alert tone is provided when Internal Paging is used. Data No.
Page 206: Delayed Ringing Time Assignment (icm)

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-2-26 Delayed Ringing Time Assignment System Mode (ICM) Submode General Description Use this Memory Block to specify the delayed ringing time for incoming internal calls. Data No. Display PC Programming S e t t i n g...
Page 207: Ps Out Of Area Time Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-2-30 PS Out of Area Time Assignment System Mode General Description Submode Use this Memory Block to specify the retry time when a PS II is Out of Area. Display Data No. S e t t i n g D a t a...
Page 208: Ip Telephone Block Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-2-32 IP Telephone Block Assignment System Mode General Description Submode Use this Memory Block to specify when IP Telephones that connect to the IPCA( )-U( ) ETU must use resources from the CPUI( )-U( ) ETU (Legacy system).
Page 209

IPC IP Telephones assigned by this Memory Block in groups of four. The Electra Elite IPK Expanded port package allows a maximum of 120 ports to be shared by station ports (ESI, SLI, OPX, FMS/VMS, etc.), Call Arrival Keys, PS Telephones, and IP Telephones. When 32 stations are used as IP Telephones, 88 station ports remain for use by the Legacy system.
Page 210: Ip Telephone Block Assignment Allow/deny Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-2-33 IP Telephone Block Assignment System Mode Allow/Deny Selection Submode General Description Use this Memory Block to designate whether or not Memory Block 1-2-32 (IP Data No. Telephone Block Assignment) is used. When this Memory Block is set to YS (Allow), Memory Block 1-2-32 can be used to assign IP Telephones to connect to the IPCA( )-U( ) ETU to use resources from the CPUI( )-U( ) (Legacy system).
Page 211

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name Card interface Slot Assignment 1-2-04 Call Arrival Key Block Assignment 1-2-21 PS Telephone Block Assignment 1-2-32 IP Telephone Block Assignment 1-5-13 Printer Connected Selection 4-07 Code Restriction Class Assignment (Day Mode)
Page 212: Expanded Station Number Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-2-34 Expanded Station Number System Mode Assignment Submode General Description Use this Memory Block to assign the lead digits when more than 4-digit station Data No. numbers are used. System Software R2500 is required.
Page 213

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-1-46 Access Code (1-Digit) Assignment 1-1-47 Access Code (2-Digit) Assignment 1-1-48 Access Code (3-Digit) Assignment 1-2-03 2~7-Digit Station Number Assignment 1-8-26 Voice Mail Quick Transfer Master Hunt Number...
Page 214: Bounce Protect Time Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-3-01 Bounce Protect Time Selection System Mode General Description Submode Use this Memory Block to specify a time for detection of a valid off-hook indication that is long enough to prevent an unintentional bounce of the receiver from being detected as a new off-hook indication from a Single Line Telephone or Voice Mail system.
Page 215: Slt Hookflash Signal Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-3-02 SLT Hookflash Signal Selection System Mode General Description Submode Use this Memory Block to specify whether a line is held internally, or when behind a PBX, a hookflash (HF) signal is sent to the line when a Single Line Telephone user performs a hookflash.
Page 216: First Digit Pbr Release Time Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-3-03 First Digit PBR Release Time System Mode Selection Submode General Description Use this Memory Block to specify the time a Push Button Receiver (PBR) circuit is Data No. connected when a dual-tone multifrequency (DTMF) Single Line Telephone user goes off-hook.
Page 217

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Display (R3000 or higher) D a t a S e t t i n g T i t l e N o . D a t a 0 3 : P B R...
Page 218: Dial 1 (dp) Hookflash Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-3-04 Dial 1 (DP) Hookflash Selection System Mode General Description Submode Use this Memory Block to specify whether or not a dial pulse (DP) Single Line Telephone provides a hookflash signal when the user presses 1 during an intercom or CO/PBX call.
Page 219: Hookflash Start Time Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-3-05 Hookflash Start Time Selection System Mode General Description Submode Use this Memory Block to specify the minimum hookflash time from a Single Line Telephone or analog Voice Mail system before it is detected as the beginning of a valid hookflash.
Page 220: Hookflash End Time Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-3-06 Hookflash End Time Selection System Mode General Description Submode Use this Memory Block to specify the maximum hookflash duration from a Single Line Telephone to receive a second dial tone. Data No.
Page 221: Voice Mail Digit Add Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-3-07 Voice Mail Digit Add Assignment System Mode General Description Submode Use this Memory Block to assign up to four digits in front of the station number sent to the voice mail when a call is forwarded.
Page 222: Voice Mail Dtmf Delay Time Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-3-08 Voice Mail DTMF Delay Time System Mode Selection Submode General Description Use this Memory Block to specify the delay time before dual-tone multifrequency Data No. (DTMF) tones are sent from Voice Mail Interface (VMI) ports.
Page 223: Voice Mail Disconnect Time Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-3-09 Voice Mail Disconnect Time Selection System Mode General Description Submode Use this Memory Block to specify the time a disconnect signal is sent to the voice mail system. Data No. Display S e t t i n g...
Page 224: Voice Mail Dtmf Duration/interdigit Time Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-3-10 Voice Mail DTMF Duration/Interdigit System Mode Time Selection Submode General Description Use this Memory Block to specify dual-tone multifrequency (DTMF) duration and Data No. interdigit time for voice mail. Display PC Programming...
Page 225: Slt/ps Ii Talk Start Timer

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-3-11 SLT/PS II Talk Start Timer System Mode General Description Submode Use this Memory Block to assign the time needed after a hookflash and dialing before three-party (two COs and one SLT) line conference is allowed from a Single Line Telephone or PSII.
Page 226

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Notes This Memory Block applies only to trunks without answer supervision (i.e., loop or ground start). A hookflash before this timer or far end answer detection, drops the new call and returns to the original call.
Page 227: Slt/isdn Telco Account Codes Allow/deny Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-3-12 SLT/ISDN TELCO Account Codes System Mode Allow/Deny Selection Submode General Description Use this Memory Block to specify when ISDN (PRI/BRI) circuits have account codes Data No. set up by TELCO that must be entered by Single Line Telephone users.
Page 228: Tandem Transfer Automatic Disconnect Time Selection

5 Program the next Memory Block or press to go back on-line. Related Programming Refer to individual features in the Electra Elite IPK Features and Specifications Manual. Notes This block is used for Direct Inward System Access (DISA), Trunk-to-Trunk Transfer, Call Forward – Off-Premise, and Tie line tandem features.
Page 229: Automated Attendant First Digit Pbr Release Time Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-4-01 Automated Attendant First Digit PBR System Mode Release Time Selection Submode General Description Use this Memory Block to specify the time a Push Button Receiver (PBR) remains Data No. connected after the Automated Attendant message is played when a calling party calls in through an Automated Attendant trunk.
Page 230

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Display (R3000 or higher) D a t a S e t t i n g T i t l e N o . D a t a 0 1 : A A P B R R L S...
Page 231: Automated Attendant Transfer Delayed Ringing Time Selections

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-4-02 Automated Attendant Transfer System Mode Delayed Ringing Time Selections Submode General Description Use this Memory Block to specify the time that a call rings at the destination station Data No. before the automated attendant rings a programmed station.
Page 232

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Display (R3000 or higher) T i m e r C l a s s D a t a S e t t i n g 1 ~ 4 N o . T i t l e...
Page 233

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Notes Example: ¤ ( D) ¤ ¤ (A) 100 (C) 102 PSTN ¤ ¤ Elite IPK (B) 101 (B) 101 ¤ ¤ (A) 100 (C) 102 Trunk 1 Time Elapsed In this example, Public Switching Telephone Network (PSTN) and the system are connected by Trunk 1.
Page 234: Automated Attendant No Answer Disconnect Time Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-4-03 Automated Attendant No Answer System Mode Disconnect Time Selection Submode General Description Use this Memory Block to specify the time the Automated Attendant rings a station Data No. before the caller is automatically disconnected.
Page 235

5 Program the next Memory Block, or press to go back on-line. Related Programming Refer to individual features in the Electra Elite IPK Features and Specifications Manual. Notes When the called party does not answer in the programmed time, the call is dropped.
Page 236: Tandem Transfer Smdr Print Extension Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-4-04 Tandem Transfer SMDR Print System Mode Extension Assignment Submode General Description Use this Memory Block to specify a special number to be output from Station Message Data No. Detail Recording (SMDR) to indicate an automatic trunk-to-trunk transfer.
Page 237: Automatic Tandem Trunk By Night Mode Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-4-05 Automatic Tandem Trunk by Night System Mode Mode Selection Submode General Description Use this Memory Block to specify whether or not the Automatic Trunk-to-Trunk Data No. Transfer feature follows the Night Mode assignment.
Page 238: Automated Attendant Pbr Timeout Response Selection

5 Program the next Memory Block or press to go back on-line. Related Programming Refer to individual features in the Electra Elite IPK Features and Specifications Manual. Notes When NORMAL is selected, and a DTMF tone is not received during the Automated Attendant message or...
Page 239: Automated Attendant Pbr Start Time Selection

5 Program the next Memory Block or press to go back on-line. Related Programming Refer to individual features in the Electra Elite IPK Features and Specifications Manual. Notes When FR is assigned, the Automated Attendant message send start time and the PBR connected to Automated Attendant trunk start time are the same.
Page 240: Automated Attendant Message Day/night Mode Selection

NT (Night) and repeat Steps 3, 4, and 5 for all messages for night Mode. The next Memory Block is displayed. 7 Program the next Memory Block or press to go back on-line. Related Programming Refer to individual features in the Electra Elite IPK Features and Specifications Manual. ___________________________________________________________________________________ Programming Manual 2 - 163...
Page 241: Automated Attendant Message To Tenant Assignment

6 Program the next Memory Block or press to go back on-line. Related Programming Refer to individual features in the Electra Elite IPK Features and Specifications Manual. Notes When a tenant is not assigned to a specific automated message, the Automated Attendant sends the message assigned in Memory Block 1-4-11 (Automated Attendant Message Day/Night Mode Selection).
Page 242: Automated Attendant Answer Delay Time Assignment

5 Repeat Steps 3 and 4 for all messages. The next Memory Block is displayed. 6 Program the next Memory Block or press to go back on-line. Related Programming Refer to individual features in the Electra Elite IPK Features and Specifications Manual. ___________________________________________________________________________________ Programming Manual 2 - 165...
Page 243: Automated Attendant Message Access Code 1-digit) Assignment

7 Continue this cycle for all Dial NOs. for all messages. The next Memory Block is displayed. 8 Program the next Memory Block or press to go back on-line. Related Programming Refer to individual features in the Electra Elite IPK Features and Specifications Manual. ___________________________________________________________________________________ 2 - 166 Memory Blocks...
Page 244

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Notes Function 011 (Bypass Automated Attendant) uses Memory Blocks 4-01 [CO/PBX Ring Assignment (Day Mode)] and 4-02 [CO/PBX Ring Assignment (Night Mode)] to ring according to those assignments. Functions 015~016 (Ring Internal Paging Zone A/B/C) require assigning the following to ring the desired station:...
Page 245

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Function Function Contents Contents Code Code Unregistered Not Used Automated Attendant Message (1) Not Used Automated Attendant Message (2) Not Used Automated Attendant Message (3) Specified Station Call (00) Refer to Memory Block 1-2-08 (Specified Station Access Code Assignment).
Page 246: Automated Attendant Message Access Code 2-digit) Assignment

7 Program the next Memory Block or press to go back on-line. Related Programming Refer to individual features in the Electra Elite IPK Features and Specifications Manual. Notes To use default 52~54, ringing must be assigned in Memory Blocks 4-01 [CO/PBX Ring Assignment (Day Mode)] or 4-02 [CO/PBX Ring Assignment (Night Mode)].
Page 247: Automated Attendant Message Repeat Selection

5 Repeat Steps 3 and 4 for each AA MSG. The next Memory Block is displayed. 6 Program the next Memory Block or press to go back on-line. Related Programming Refer to individual features in the Electra Elite IPK Features and Specifications Manual. ___________________________________________________________________________________ 2 - 170 Memory Blocks...
Page 248: Automated Attendant Delay Announcement Hold Tone Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-4-17 Automated Attendant Delay System Mode Announcement Hold Tone Selection Submode General Description Use this Memory Block to specify the tone to be sent to the outside party after the Data No. Automated Attendant Delay Announcements are played.
Page 249: Automated Attendant Delay Announcement Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-4-18 Automated Attendant Delay System Mode Announcement Assignment Submode General Description Use this Memory Block to specify the order for the Automated Attendant messages Data No. that are played in Delayed Announcement Mode.
Page 250

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-4-19 Automated Attendant 1 to 2 Delay System Mode Announcement Interval Time Selection Submode Data No. General Description Use this Memory Block to specify the time, in seconds or minutes, between the Automated Attendant Delay Announcement messages.
Page 251: Automated Attendant Delay Announcement Disconnect Time Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-4-20 Automated Attendant Delay System Mode Announcement Disconnect Time Selection Submode Data No. General Description Use this Memory Block to establish the time, in seconds or minutes, the Automated Attendant rings the station before disconnecting the caller. This Memory Block only PC Programming applies when the Automated Attendant is set to Delay Announcement Mode.
Page 252: Automated Attendant Extension Number Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-4-21 Automated Attendant Extension System Mode Number Assignment Submode General Description Use this Memory Block to specify the Automated Attendant message to be played Data No. when a DID call is received. Display...
Page 253: Automated Attendant Direct Extension Ring Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-4-22 Automated Attendant Direct System Mode Extension Ring Assignment Submode General Description Use this Memory Block to specify the Automated Attendant message to be played for Data No. direct transfer to the extension number.
Page 254: Smdr Print Format

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-5-02 SMDR Print Format System Mode General Description Submode Use this Memory Block to specify whether or not all digits are printed. When ALL is specified, all digits are printed. When MSK (Mask) is specified, the last four digits are masked and printed as XXXX.
Page 255: Printer Connected Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-5-13 Printer Connected Selection System Mode General Description Submode Use this Memory Block to program printer connection. When the printer is not connected to the system, an alarm sounds at stations connected to Ports 01 and 02.
Page 256: Printer Line Feed Control Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-5-14 Printer Line Feed Control Selection System Mode General Description Submode Use this Memory Block to specify the data format to be sent to the Station Message Detail Recording (SMDR) printer. When YS is set, a return is provided with the call record.
Page 257

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Notes Example: Settings to specify the format of communication data output to the printer. Line Feed control in effect. 07/03/92 09:00 08-05-12 OG 123 00:15:32 102885167537000 FWD234 12345678 No Line Feed control. 07/03/92...
Page 258: Smdr Valid Call Time Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-5-25 SMDR Valid Call Time Assignment System Mode General Description Submode Use this Memory Block to assign the minimum call time before the Station Message Detail Recording (SMDR) outputs a record of the outgoing CO/PBX call.
Page 259: Smdr Incoming/outgoing Print Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-5-26 SMDR Incoming/Outgoing Print System Mode Selection Submode General Description Use this Memory Block to specify the call records to be output from the Station Data No. Message Detail Recording (SMDR): OUT = print outgoing call records only, INC = print incoming call records only, ALL = print incoming and outgoing call records.
Page 260: Attendant Add-on Console To Telephone Port Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-6-01 Attendant Add-On Console to System Mode Telephone Port Assignment Submode General Description Use this Memory Block to assign an Attendant Add-On Console to a telephone port Data No. number. Display PC Programming...
Page 261: Dss Call Voice/tone Signal Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-6-03 DSS Call Voice/Tone Signal Selection System Mode General Description Submode Use this Memory Block to specify whether Voice or Tone signaling is to be used first when calling an extension from an Attendant Add-On Console.
Page 262: Attendant Add-on Console Key Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-6-05 Attendant Add-On Console Key System Mode Selection Submode General Description Use this Memory Block to assign functions to the Attendant Add-On Console keys. Data No. Display PC Programming D S S B u t t o n...
Page 263

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Programming Procedures (Continued) 3 Press the corresponding CO/PBX line key and dial pad keys to change the data Default Values option: Key No. Data Setting Functions can be assigned to keys 01~60 on Attendant Add-On Consoles 1~4.
Page 264

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-6-01 Attendant Add-On Console to Telephone Port Assignment Telephone Type Assignment Notes When TEL is assigned to a line key, the red LED is used to indicate Station Status.
Page 265: Message Board Lamp Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-6-07 Message Board Lamp Assignment System Mode General Description Submode Use this Memory Block to assign mailbox numbers for each Message Display Board. Display Data No. L a m p S e t t i n g...
Page 266: Attendant Transfer Selection During Live Record

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-6-08 Attendant Transfer Selection During System Mode Live Record Submode General Description Use this Memory Block to control the Attendant DSS/BLF transfer while the Attendant Data No. is engaged in Live Record. The call is transferred to either the DSS/BLF extension or the voice mailbox of the DSS/BLF extension.
Page 267

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ THIS PAGE INTENTIONALLY LEFT BLANK ___________________________________________________________________________________ 2 - 190 Memory Blocks...
Page 268: Doorphone Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-7-00 Doorphone Assignment System Mode General Description Submode Use this Memory Block to enable the doorphones in System Programming. Display Data No. D a t a T i t l e N o .
Page 269: Doorphone Display Time Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-7-01 Doorphone Display Time Selection System Mode General Description Submode Use this Memory Block to specify the time, in seconds, a doorphone call signals a station before it times out. Data No. This Memory Block can be adjusted in 1-second intervals (R3000 or higher).
Page 270

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Display (R3000 or higher) D a t a S e t t i n g T i t l e N o . D a t a 0 1 : D P H...
Page 271: External Speaker Connection Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-7-02 External Speaker Connection System Mode Selection Submode General Description Use this Memory Block to specify whether or not external speakers are connected to Data No. the system. Display PC Programming D a t a N o .
Page 272: External Paging Alert Tone Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-7-03 External Paging Alert Tone Selection System Mode General Description Submode Use this Memory Block to specify whether or not a paging alert tone is sent on External Zone Paging (all speakers/individual speaker).
Page 273: Doorphone Ring Pattern Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-7-04 Doorphone Ring Pattern Selection System Mode General Description Submode Use this Memory Block to turn doorphone Off/On or specify the doorphone ring pattern. Doorphones can be individually assigned. Data No. Display S e t t i n g...
Page 274

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ The Doorphone Ring Patterns are shown in the table below: s= seconds Line Pattern Tone LK 1 Tone LK 2 LK 3 LK 4 LK 5 LK 6 LK 7 LK 8 LK 1 (Pg.
Page 275: Doorphone Ringing Frequency Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-7-05 Doorphone Ringing Frequency System Mode Selection Submode General Description Use this Memory Block to specify the doorphone ringing frequency. Doorphones can Data No. be individually assigned. Display PC Programming +BTP S e t t i n g...
Page 276

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-7-00 Doorphone Assignment 1-7-04 Doorphone Ring Pattern Selection 4-03 Doorphone Chime Assignment (Day Mode) 4-04 Doorphone Chime Assignment (Night Mode) ___________________________________________________________________________________ Programming Manual 2 - 199...
Page 277: External Paging Timeout Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-7-06 External Paging Timeout Selection System Mode General Description Submode Use this Memory Block to specify the time allowed for External Paging before timeout and release of the paging circuit. R1000/R2500/R3500 Speaker 59 uses this timer.
Page 278

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Display (R3000 or higher) T i m e r C l a s s D a t a S e t t i n g 1 ~ 4 N o . T i t l e...
Page 279: External Ring Relay Pattern Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-7-07 External Ring Relay Pattern Selection System Mode General Description Submode Use this Memory Block to assign a distinctive ringing control/interval pattern to relay circuits. Data No. Display E x t R i n g...
Page 280

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ s= seconds Pattern Continuous ___________________________________________________________________________________ Programming Manual 2 - 203...
Page 281: External Speaker Chime Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-7-08 External Speaker Chime Selection System Mode General Description Submode Use this Memory Block to specify whether a normal paging alert tone (4 tones) sounds before the speech path is established, a chime sounds at the start of the call, or a chime sounds at the start and end of the call.
Page 282: External Speaker Chime Start Time Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-7-09 External Speaker Chime Start Time System Mode Selection Submode General Description Use this Memory Block only when paging alert tone (four tones) is assigned in Data No. Memory Block 1-7-08 (External Speaker Chime Selection). This Memory Block specifies the delay time (in milliseconds) after an external paging code is dialed before the paging alert tone is provided.
Page 283

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ THIS PAGE INTENTIONALLY LEFT BLANK ___________________________________________________________________________________ 2 - 206 Memory Blocks...
Page 284: Slt Or Automated Attendant/disa To Cpu Pbr Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-8-01 SLT or Automated Attendant/DISA to System Mode CPU PBR Selection Submode General Description Use this Memory Block to specify whether the four Push Button Receiver (PBR) Data No. circuits in the CPUI( )-U( ) ETU are used for Single Line Telephones or Automated Attendant/Direct Inward System Access (DISA).
Page 285: Pbr Receive Level Assignment For Automated Attendant/disa

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-8-02 PBR Receive Level Assignment for System Mode Automated Attendant/DISA Submode General Description Use this Memory Block to specify the receiving level of the Push Button Receiver Data No. (PBR) at the Automated Attendant/Direct Inward System Access (DISA).
Page 286

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Notes When the Automated Attendant answers, the DTMF signal level from the calling party is reduced from the Public Switched Telephone Network (PSTN). This Memory Block specifies the minimum detectable receiving level. Setting Data 15 is the most sensitive.
Page 287: Time Display (12h/24h) Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-8-04 Time Display (12h/24h) Selection System Mode General Description Submode Use this Memory Block to specify either a 12-hour (00:00 to 11:59 a.m., noon to 11:59 p.m.) or 24-hour (00:00 to 23:59) time display.
Page 288: Class Of Service (attendant) Feature Selection 1

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-8-07 Class of Service (Attendant) Feature System Mode Selection 1 Submode General Description Use this Memory Block to allow or deny specific attendant features for each Class Of Data No. Service. When individual stations are assigned, the station user can access only the features designated as allow.
Page 289

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Programming Procedures Go off-line. Press LK1 + LK8 + to access the Memory Block. Press the corresponding CO/PBX line key to enter data. The LED indication changes to indicate the data each time a CO/PBX line key is pressed.
Page 290

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Classes 00 15 are programmed in this Memory Block as feature restriction classes. In Memory Block 4-17 (Station to Class of Service Feature Assignment) specify any class of service for each telephone to assign features the user can/ cannot activate.
Page 291: Class Of Service (station) Feature Selection 2

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-8-08 Class of Service (Station) Feature System Mode Selection 2 Submode General Description Use this Memory Block to allow or deny specific station features for each Class of Data No. Service. When individual stations are assigned, the station user can access only the features specified as allow.
Page 292

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Page 5 LK 1 LK 2 LK 3 LK 4 LK 5 LK 6 LK 7 LK 8 Forced Group Set Call Pre-Set ANI/Caller ID Account Code Station Live Listening Forward – Off...
Page 293

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 4-17 Station to Class of Service Feature Assignment Notes Sixteen Classes (00 15) of feature restriction patterns allow a station user to activate particular features while restricting others.
Page 294

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Corresponding Default Default CO/PBX Function Name Class 00 Class 01 Line Key Page 1 Set Call Forward – All Call, Do Not Disturb (DND), Break Mode Allow Deny Trunk Queuing Allow Deny Automatic Callback...
Page 295

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Corresponding Default Default CO/PBX Function Name Class 00 Class 01 Line Key Page 4 LCR/ARS Recall Allow Deny DSS Key Transfer Operation Deny Deny ANI/Caller ID Deny Deny ANI/Caller ID Number/Name Selection Deny Deny When deny is set, Name is displayed if Name and number are received.
Page 296

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Corresponding Default Default CO/PBX Function Name Class 00 Class 01 Line Key Save Caller ID Missed Call Information (R3000 or higher) Deny Deny (Version 6.00 MIFM or higher) Page 7 Send Caller ID Information to SLT (R3000 or higher)
Page 297: Music On Hold Pattern Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-8-09 Music on Hold Pattern Selection System Mode General Description Submode Use this Memory Block to specify the Music on Hold pattern. Display Data No. S e t t i n g D a t a...
Page 298: Pbr Interdigit Release Time Selection

First Digit PBR Release Time Selection 1-8-01 SLT or Automated Attendant/DISA to CPU PBR Selection Notes A DTMF Single Line Telephone connected to the Electra Elite IPK system must be supported by a PBR that receives DTMF signals. ___________________________________________________________________________________ Programming Manual...
Page 299

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Off-hook Specified Time: 10 sec. Default Dial Tone is sent (PBR connected) Memory Block 1-3-03 Dial the first digit. Specified Time: 7 sec. Default Memory Block 1-8-10 Dial the second digit. Specified Time: 7 sec. Default...
Page 300: System Refresh Time Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-8-11 System Refresh Time Assignment System Mode General Description Submode Use this Memory Block to assign the System Refresh Time during idle periods. Display Data No. D a t a S e t t i n g T i t l e N o .
Page 301: Vrs Message Recording Time Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-8-12 VRS Message Recording Time System Mode Selection Submode General Description Use this Memory Block to specify the recording time and number of messages for Data No. each Voice Recording Service (VRS) channel.
Page 302: Vrs Message Function Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-8-13 VRS Message Function Assignment System Mode General Description Submode Use this Memory Block to assign the recorded voice prompt Delay Announcement/ Automated Attendant Message to the Voice Recording Service (VRS) Message number. Refer to Memory Block 1-8-12 (VRS Message Recording Time Selection).
Page 303

Repeat Steps 3 and 4 for each message for each VRS. The next Memory Block is displayed. Program the next Memory Block or press to go back on-line. Related Programming Refer to individual features in the Electra Elite IPK Features and Specifications Manual. ___________________________________________________________________________________ 2 - 226 Memory Blocks...
Page 304: Tone Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-8-15 Tone Assignment System Mode General Description Submode Use this Memory Block to assign each system tone to the flexible tables. Display Data No. T a b l e D a t a N o .
Page 305

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Table Tone Default Number ICM Dial Tone Second Dial Tone Special Dial Tone SPDT Busy Tone Reorder/Error Tone Howler Tone Service Set Tone ICM Ringback Tone RBT1 Tie/DID Ringback RBT2 Tone Call Waiting Tone...
Page 306

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Tone Frequency Intermit Cycle 350/440 Continuous 350/440 120 IPM 0.25 On, 0.25 Off 240 IPM 0.125 On, 0.125 Off 480/620 60 IPM 0.5 On, 0.5 Off 480/620 120 IPM 2400 Continuous Modulation Continuous...
Page 307: Voice Prompt To Tone Assignment

The next Memory Block is displayed. Program the next Memory Block or press to go back on-line. Related Programming Refer to individual features in the Electra Elite IPK Features and Specifications Manual. ___________________________________________________________________________________ 2 - 230 Memory Blocks...
Page 308: Pc Programming Password Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-8-17 PC Programming Password System Mode Assignment Submode General Description Use this Memory Block to assign system passwords that must be entered when Data No. connecting to the system using SAT PC Programming.
Page 309: Site Name Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-8-18 Site Name Assignment System Mode General Description Submode Use this Memory Block to specify a site name for PC Programming software to use to program the system. Data No. Display PC Programming...
Page 310: Acd/ucd Group Agent Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-8-25 ACD/UCD Group Agent Assignment System Mode General Description Submode Use this Memory Block to specify the Agent Station Number and the Automatic Call Distribution/Uniform Call Distribution (ACD/UCD) Group Number where each agent is assigned.
Page 311: Voice Mail Quick Transfer Master Hunt Number

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-8-26 Voice Mail Quick Transfer Master System Mode Hunt Number Submode General Description Use this Memory Block to specify a Voice Mail Master Hunt Number to operate Quick Data No. Transfer to Voice Mail. This Memory Block also enables the voice mail display in the LCD of a Multiline Terminal when a voice mail machine sets a message.
Page 312

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Programming Procedures Program next Memory Block or press to go back on-line. Related Programming M.B. Number Memory Block Name 1-1-46 Access Code (1-Digit) Assignment 1-1-47 Access Code (2-Digit) Assignment 1-1-48 Access Code (3-Digit) Assignment...
Page 313: Forced Account Code/authorization Code Length Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-8-27 Forced Account Code/Authorization System Mode Code Length Assignment Submode General Description Use this Memory Block to specify the number of digits for the Forced Account Code/ Data No. Authorization Code. Display PC Programming...
Page 314

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Related Programming (Continued) M.B. Number Memory Block Name 4-64 Code Restriction Class (Without Authorization Code) Day Mode Assignment 4-65 Code Restriction Class (Without Authorization Code) Night Mode Assignment ___________________________________________________________________________________ Programming Manual 2 - 237...
Page 315: Scd (simplified Call Distribution) Pilot Number Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-8-29 SCD (Simplified Call Distribution) System Mode Pilot Number Assignment Submode General Description Use this Memory Block to specify the SCD Pilot number for each group. Any valid Data No. unused station number can be used.
Page 316: Scd Group Agent Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-8-30 SCD Group Agent Assignment System Mode General Description Submode Use this Memory Block to assign stations to one of four simplified call distribution groups. A total of 32 stations can be assigned.
Page 317: Hold Tone Source Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-8-31 Hold Tone Source Assignment System Mode General Description Submode Use this Memory Block to assign an internal or external Music on Hold source. Display Data No. D a t a S e t t i n g N o .
Page 318: Hold Internal Tone Volume Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-8-32 Hold Internal Tone Volume Selection System Mode General Description Submode When the internal Music On Hold source is used, this Memory Block can be used to pad the music by -6 dB.
Page 319: Master Clock Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-8-33 Master Clock Selection System Mode General Description Submode When a DTI-U( ) ETU (T-1), PRT(1)-U( ) ETU, or BRT(4)-U( ) ETU is installed, clocking must be synchronized. When this Memory Block is set for Cabinet 0 (default), the system is set to be a Master Clock source.
Page 320

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Example 2: (The PSTN is Master Clock Source) Electra Elite ISDN Electra Elite Electra Elite PSTN Cabinet 1 Cabinet 1 Cabinet 1 Cabinet 1 Cabinet 1 Slot 1 Slot 1 Slot 4 Slot 4...
Page 321: Com Port Baud Rate Setting Assignment

Notes COM 1 = PC Programming COM 1 = LCR COM 2 = Station Message Detail Recording (SMDR) COM 3 = Automatic Call Distribution [Not used by Electra Elite IPK Basic Port Package (48).] ___________________________________________________________________________________ 2 - 244 Memory Blocks...
Page 322: Com Port Parity/stop Bit Setting Assignment

Notes COM 1 = PC Programming COM 1 = LCR COM 2 = Station Message Detail Recording (SMDR) COM 3 = Automatic Call Distribution [Not used by Electra Elite IPK Basic Port Package (48).] ___________________________________________________________________________________ Programming Manual 2 - 245...
Page 323: General Purpose Relay Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-8-37 General Purpose Relay Assignment System Mode General Description Submode Use this Memory Block to specify whether or not the General Purpose Relays on the ECR-U( ) ETU are used. Data No. Display...
Page 324: Modem Number For Remote Programming Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-8-38 Modem Number For Remote System Mode Programming Assignment Submode General Description A socket modem can be installed on the MIFM-U( ) ETU when it is installed in S1 or Data No. S2 of the B64-U20 KSU. Use this Memory Block to assign the extension number for the socket modem.
Page 325: Acd Hunt Time

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-8-40 ACD Hunt Time System Mode General Description Submode Use this Memory Block to assign the time for hunting among the Automatic Call Distribution/Uniform Call Distribution (ACD/UCD) agents that do not answer an ACD/ UCD call.
Page 326: Enhanced 911 Trunk Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-8-43 Enhanced 911 Trunk Assignment System Mode General Description Submode Use this feature to define an available loop-start trunk as a CAMA or an ISDN PRI trunk. When a user dials 911, the system seizes the E911 trunk and sends additional digits (CESID) to enable the PSAP center to recognize the callback telephone Data No.
Page 327

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-8-44 Enhanced 911 Alternate Route Assignment 1-8-45 Enhanced 911 Alternate Route Assignment (Maintenance Busy) 1-8-46 Enhanced 911 Dialing Digit Assignment 1-15-19 Centralized 911 Allow/Deny Selection 1-15-20...
Page 328: Enhanced 911 Alternate Route Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-8-44 Enhanced 911 Alternate Route System Mode Assignment Submode General Description Use this Memory Block to specify the trunk route or route advance block to be seized Data No. when the E911 trunk is busy. Normally, this Memory Block is left unassigned.
Page 329: Enhanced 911 Alternate Route Assignment (maintenance Busy)

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-8-45 Enhanced 911 Alternate Route System Mode Assignment (Maintenance Busy) Submode General Description Use this Memory Block to specify the trunk route or route advance block to be seized Data No. when the E911 trunk is in maintenance busy or trouble out of service.
Page 330

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Notes When the E911 trunk is maintenance busy or trouble out of service, E911 calls are routed to the trunk group assigned by E911 Alternate Route Assignment. One trunk group or one route advance block per system can be specified.
Page 331: Enhanced 911 Dialing Digit Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-8-46 Enhanced 911 Dialing Digit System Mode Assignment Submode General Description Use this Memory Block to specify the number of digits to be sent when a call is Data No. originated by dialing 911.
Page 332: Call Arrival Key Voice Mail Message Notification Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-8-47 Call Arrival Key Voice Mail Message System Mode Notification Assignment Submode General Description Use this Memory Block to assign the Call Arrival Key that is used to send Voice Mail Data No.
Page 333: Automatic Daylight Saving Time Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-8-48 Automatic Daylight Saving Time System Mode Selection Submode General Description Use this Memory Block to allow (YS) or deny (NO) the system clock adjustment for Data No. Daylight Saving Time. Display PC Programming...
Page 334: New Aa-info Yes/no Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-8-49 New AA-Info Yes/No Selection System Mode General Description Submode Use this Memory Block to specify whether or not New AA-Info is allowed. New Application-to-Application (AA) Info is used with internal Voice Mail Systems [i.e.,CMS( )-U( ), FMS( )-U( ), or VMS( )-U( ) ETUs].
Page 335

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Table 2-1 Voice Mail AA-Info Settings DOS Based Voice Mails Hardware Type Voice Mail Q Revision Correct AA Info Type EliteMail U10/U20 FMS Q26031 or lower VMS Q30931 or lower EliteMail U20/U30 ALL CMS...
Page 336

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name Card interface Slot Assignment Telephone Type Assignment 1-1-46 Access Code (1-Digit) Assignment Functions 020, 025, 027, 030, 032~034, 140~145 1-1-47 Access Code (2-Digit) Assignment Functions 020, 025, 027, 030, 032~034, 140~145...
Page 337: Call Park Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-8-51 Call Park Selection System Mode General Description Submode Use this Memory Block to assign either 10 or 40 Call Park – System Locations. Display Data No. D a t a S e t t i n g N o .
Page 338: Disa Id Code Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-9-00 DISA ID Code Assignment System Mode General Description Submode Use this Memory Block to specify the Direct Inward System Access (DISA) ID Code number. Data No. Display I D B u f f e r PC Programming N o .
Page 339: Disa Password Effect/invalid Selection

Buffer No. 01 on Memory Block 1-9-00. 6 Press to go back on-line. Related Programming Refer to individual features in the Electra Elite IPK Features and Specifications Manual. ___________________________________________________________________________________ 2 - 262 Memory Blocks...
Page 340: Call By Call Type Of Network Id Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-10-00 Call by Call Type of Network ID System Mode Assignment Submode General Description Use this Memory Block to send the Type of Number ID (TNI) for each Route Advance Data No. Block (RAB). This setting data is sent in the TNI field of the NSF-IE (Network Specified Facility-Information Element) when making outgoing calls.
Page 341

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 3-03 Trunk-to-Trunk Group Assignment 1-1-30 Route Advance Block Assignment 1-1-46, 47, 48 Access Code (1-, 2-, or 3-Digit) Assignment 1-10-01 Call by Call ID Plan Assignment...
Page 342: Call By Call Id Plan Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-10-01 Call by Call ID Plan Assignment System Mode General Description Submode Use this Memory Block to send the Network ID Plan (NIP) for each Route Advance Block (RAB). This setting data is sent in the NIP field of the NSF-IE (Network Specified Facility-Information Element) when making outgoing calls.
Page 343

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 3-03 Trunk-to-Trunk Group Assignment 1-1-30 Route Advance Block Assignment 1-1-46, 47, 48 Access Code (1-, 2-, or 3-Digit) Assignment 1-10-00 Call by Call Type of Network ID Assignment...
Page 344: Call By Call Type Of Number Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-10-02 Call by Call Type of Number System Mode Assignment Submode General Description Use this Memory Block to send the Type of Number (TN) for each Route Advance Data No. Block (RAB). This setting data is sent in the TN field of the CPN-IE (Called Party Number-Information Element) when making outgoing calls.
Page 345

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 3-03 Trunk-to-Trunk Group Assignment 1-1-30 Route Advance Block Assignment 1-1-46, 47, 48 Access Code (1-, 2-, or 3-Digit) Assignment 1-10-00 Call by Call Type of Network ID Assignment...
Page 346: Call By Call Numbering Plan Id Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-10-03 Call by Call Numbering Plan ID System Mode Assignment Submode General Description Use this Memory Block to send the Numbering Plan Identification (NPI) for each Route Data No. Advance Block (RAB). This setting data is sent in the NPI field of the CPN-IE (Called Party Number-Information Element) when making outgoing calls.
Page 347

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 3-03 Trunk-to-Trunk Group Assignment 1-1-30 Route Advance Block Assignment 1-1-46, 47, 48 Access Code (1-, 2-, or 3-Digit) Assignment 1-10-00 Call by Call Type of Network ID Assignment...
Page 348: Call By Call Network Id Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-10-04 Call by Call Network ID Assignment System Mode General Description Submode Use this Memory Block to send the Network Identification (NID) for each Route Advance Block (RAB). This setting data is sent in the NID field of the CIC-IE (Carrier Identification Code-Information Element) when making outgoing calls.
Page 349

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-10-07 Call by Call Service Parameter Assignment 1-10-08 Call by Call Max Digit Assignment 1-10-09 Call by Call Simulated Facility Group Assignment 1-10-20 Call by Call Outgoing SFG Assignment...
Page 350: Call By Call Facility Coding Value Assignment (service)

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-10-05 Call by Call Facility Coding Value System Mode Assignment (Service) Submode General Description Use this Memory Block to specify the Facility Coding Value (Service) for each Route Data No. Advance Block (RAB). This setting data is sent in the FCV-S field of the NSF-IE (Network Specific Facility Code-Information Element) when making outgoing calls.
Page 351

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Programming Procedures 4 Press to write the data. The next Memory Block is displayed. 5 Program the next Memory Block or press to go back on-line. Related Programming M.B. Number Memory Block Name...
Page 352: Call By Call Facility Coding Value Assignment (feature)

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-10-06 Call by Call Facility Coding Value System Mode Assignment (Feature) Submode General Description Use this Memory Block to specify the Facility Coding Value (Feature) for each Route Data No. Advance Block (RAB). This setting data is sent in the FCV-F field of the NSF-IE (Network Specific Facility Code-Information Element) when making outgoing calls.
Page 353

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 3-03 Trunk-to-Trunk Group Assignment 1-1-30 Route Advance Block Assignment 1-1-46, 47, 48 Access Code (1-, 2-, or 3-Digit) Assignment 1-10-00 Call by Call Type of Network ID Assignment...
Page 354: Call By Call Service Parameter Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-10-07 Call by Call Service Parameter System Mode Assignment Submode General Description Use this Memory Block to specify the Service Parameters for each Route Advance Data No. Block (RAB). This setting data is sent to the Service Parameters in the NSF-IE (Network Specific Facility Code-Information Element) when making outgoing calls.
Page 355

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 3-03 Trunk-to-Trunk Group Assignment 1-1-30 Route Advance Block Assignment 1-1-46, 47, 48 Access Code (1-, 2-, or 3-Digit) Assignment 1-10-00 Call by Call Type of Network ID Assignment...
Page 356: Call By Call Max Digit Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-10-08 Call by Call Max Digit Assignment System Mode General Description Submode Use this Memory Block to specify the maximum digits dialed for each Route Advance Block (RAB). When the maximum digits are dialed, the PRT(1)-U( ) ETU sends SETUP information to the ISDN Provider (Network).
Page 357

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-10-06 Call by Call Facility Coding Value Assignment (Feature) 1-10-07 Call by Call Service Parameter Assignment 1-10-09 Call by Call Simulated Facility Group Assignment 1-10-20 Call by Call Outgoing SFG Assignment...
Page 358: Call By Call Simulated Facility Group Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-10-09 Call by Call Simulated Facility Group System Mode Assignment Submode General Description Use this Memory Block to specify the Simulated Facility Group (SFG) for each Route Data No. Advance Block (RAB). Display...
Page 359

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-10-05 Call by Call Facility Coding Value Assignment (Service) 1-10-06 Call by Call Facility Coding Value Assignment (Feature) 1-10-07 Call by Call Service Parameter Assignment 1-10-08...
Page 360: Call By Call Outgoing Sfg Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-10-20 Call by Call Outgoing SFG System Mode Assignment Submode General Description Use this Memory Block to specify the outgoing call service assignment for the Data No. Simulated Facility Group (SFG). Display PC Programming...
Page 361

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-10-03 Call by Call Numbering Plan ID Assignment 1-10-04 Call by Call Network ID Assignment 1-10-05 Call by Call Facility Coding Value Assignment (Service) 1-10-06 Call by Call Facility Coding Value Assignment (Feature)
Page 362: Call By Call Outgoing/incoming Sfg Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-10-21 Call by Call Outgoing/Incoming SFG System Mode Assignment Submode General Description Use this Memory Block to specify the outgoing/incoming call service assignment for Data No. the Simulated Facility Group (SFG). Display PC Programming...
Page 363

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-10-05 Call by Call Facility Coding Value Assignment (Service) 1-10-06 Call by Call Facility Coding Value Assignment (Feature) 1-10-07 Call by Call Service Parameter Assignment 1-10-08...
Page 364: Call By Call Incoming Type Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-10-22 Call by Call Incoming Type Selection System Mode General Description Submode Use this Memory Block to specify the type of trunk for each Simulated Facility Group (SFG). Data No. Display D a t a...
Page 365

Call by Call Outgoing/Incoming SFG Assignment 1-13-03 Call by Call Service Selection Notes Refer to individual features in the Electra Elite IPK Features and Specifications Manual for correct routing of calls for Direct Inward Dialing. ___________________________________________________________________________________ 2 - 288 Memory Blocks...
Page 366: T1 Signal Format Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-11-00 T1 Signal Format Selection System Mode General Description Submode Use this Memory Block to specify the signal format of the T1 trunk connected to the system. The signal format used (12- or 24-Multiframe) depends on the channel service unit/demarcation (CSU/D mark) equipment being used.
Page 367: Clear Channel Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-11-01 Clear Channel Selection System Mode General Description Submode Use this Memory Block to specify the clear channel selection. when the Zero Byte Time channel is available, the CLKG-U( ) Unit cannot extract a clock signal from the T1 trunk.
Page 368: Line Length Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-11-02 Line Length Selection System Mode General Description Submode Use this Memory Block to specify the distance, in feet, between the channel service unit/demarcation (CSU/D mark) and the DTI-U( ) ETU. This specifies the equalization values of the detect signal in the DTI-U( ) ETU.
Page 369: Ip K-ccis Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-11-03 IP K-CCIS Selection System Mode General Description Submode Use this Memory Block to assign the IAD(8)-U( ) ETU used for K-CCIS over IP. System Software R1500~R1700 or R2500 is required. Data No.
Page 370

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-15-16 Centralized BLF Send Extension Number Assignment 1-15-17 Centralized BLF Send Time Assignment 1-15-18 Centralized BLF Display Extension Number Assignment Notes The IAD(8)-U( ) ETU is programmed as a DTI (DTI4 or DTI8) ETU in Memory Block 7-1 (Card Interface Slot Assignment) when used for K-CCIS over IP.
Page 371: T1 Channel Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-11-05 T1 Channel Selection System Mode General Description Submode Use this Memory Block to specify the digital trunk interface (DTI) channel numbers to be used. Data No. Display D a t a D T I N o .
Page 372

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name Card Interface Slot Assignment Notes The DTI-U( ) ETU must be assigned in the system to set this Memory Block. ___________________________________________________________________________________ Programming Manual 2 - 295...
Page 373: Signaling Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-11-06 Signaling Selection System Mode General Description Submode Use this Memory Block to specify Loop Start (LS) or Ground Start (GS) Trunk Signaling when using T1. Data No. Display S e t t i n g D T I N o .
Page 374: Dti Trunk Type Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-11-07 DTI Trunk Type Assignment System Mode General Description Submode Use this Memory Block to assign the trunk type (CO/E&M Tie line/DID/ANI) four channels at a time. Assignment to an individual channel is impossible.
Page 375

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-11-06 Signaling Selection Card Interface Slot Assignment Notes A DTI-U( ) ETU must be assigned in the system to set this Memory Block. When the default setting is changed to E&M or DID, the affected trunks are automatically reassigned to Trunk Group 00.
Page 376: Digits Delete For T1 Ani Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-11-08 Digits Delete for T1 ANI Assignment System Mode General Description Submode Use this Memory Block to delete the Information Digits received from the Network on Feature Group D Trunks. Data No. Display...
Page 377

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Programming Procedures 5 Program Memory Block 1-11-00 again or press to go back on-line. Related Programming M.B. Number Memory Block Name Card interface Slot Assignment 1-11-05 T1 Channel Selection 1-11-07 DTI Trunk Type Assignment Notes Example of ANI information: KP009727517645STKP7100ST.
Page 378: Acd/ucd Group Pilot Number Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-12-00 ACD/UCD Group Pilot Number System Mode Assignment Submode General Description Use this Memory Block to specify the Pilot Number of an Automatic Call Distribution/ Data No. Uniform Call Distribution (ACD/UCD) Group where incoming calls are terminated.
Page 379

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-8-25 ACD/UCD Group Agent Assignment 1-12-01 ACD/UCD Group Overflow Destination Assignment ___________________________________________________________________________________ 2 - 302 Memory Blocks...
Page 380: Acd/ucd Group Overflow Destination Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-12-01 ACD/UCD Group Overflow System Mode Destination Assignment Submode General Description Use this Memory Block to specify the station or Station Hunt group where the overflow Data No. call of each Automatic Call Distribution/Uniform Call Distribution (ACD/UCD) group is routed when incoming calls overflow.
Page 381

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Notes An ACD/UCD Group Pilot Number cannot be programmed as the overflow destination. UCD and ACD cannot be installed in the same system. ___________________________________________________________________________________ 2 - 304 Memory Blocks...
Page 382: Acd/ucd Overflow Time Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-12-02 ACD/UCD Overflow Time Selection System Mode General Description Submode Use this Memory Block to specify the maximum time a waiting Automatic Call Distribution/Uniform Call Distribution (ACD/UCD) call remains at an ACD/UCD group before overflowing to a specified Station or Station Hunt group.
Page 383

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ THIS PAGE INTENTIONALLY LEFT BLANK ___________________________________________________________________________________ 2 - 306 Memory Blocks...
Page 384: Prt Channel Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-13-00 PRT Channel Assignment System Mode General Description Submode Use this Memory Block to assign the available B channels used for PRI. Display Data No. D a t a S e t t i n g...
Page 385

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name Card interface Slot Assignment 1-13-01 PRT Signal Format Selection 1-13-02 Clear Channel Selection 1-13-03 Call by Call Service Selection 1-13-04 PRT B Channel Outgoing Priority Selection...
Page 386: Prt Signal Format Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-13-01 PRT Signal Format Selection System Mode General Description Submode Use this Memory Block to specify the signal format of the PRT trunk connected to the system. The signal format used (12- or 24-Multiframe) depends on the channel service unit/demarcation (CSU/D mark) equipment being used.
Page 387

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name Card interface Slot Assignment 1-13-01 PRT Signal Format Selection 1-13-03 Call by Call Service Selection 1-13-04 PRT B Channel Outgoing Priority Selection 1-13-05 PRT B Channel-to-Trunk Group Assignment...
Page 388

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-13-02 Clear Channel Selection System Mode General Description Submode Use this Memory Block to specify the clear channel selection. When the Zero Byte Time channel is available, the CLKG-U( ) Unit cannot extract a clock signal from the PRT trunk.
Page 389: Call By Call Service Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-13-03 Call by Call Service Selection System Mode General Description Submode Use this Memory Block to specify whether or not Call by Call Service is activated per PRT. Data No. Display D a t a...
Page 390: Prt B Channel Outgoing Priority Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-13-04 PRT B Channel Outgoing Priority System Mode Selection Submode General Description Use this Memory Block to assign the Outgoing Priority for the B-channels when calls Data No. are originated on a PRT(1)-U( ) ETU.
Page 391: Prt B Channel-to-trunk Group Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-13-05 PRT B Channel-to-Trunk Group System Mode Assignment Submode General Description Use this Memory Block to assign a Trunk Group Number to each B channel or any Data No. Trunk Group for each B channel. Changing this assignment is not normally required and default should be set.
Page 392

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name Card Interface Slot Assignment 1-13-00 PRT Channel Assignment 1-13-01 PRT Signal Format Selection 1-13-02 Clear Channel Selection 1-13-03 Call by Call Service Selection 1-13-04 PRT B Channel Outgoing Priority Selection...
Page 393

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ THIS PAGE INTENTIONALLY LEFT BLANK ___________________________________________________________________________________ 2 - 316 Memory Blocks...
Page 394: Ars Allow/deny Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-14-00 ARS Allow/Deny Selection System Mode General Description Submode Use this Memory Block to specify system wide whether or not Automatic Route Selection (ARS) is allowed. Data No. Display D a t a...
Page 395: Ars Dialing Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-14-01 ARS Dialing Assignment System Mode General Description Submode Use this Memory Block to assign a dialing plan to one of four ARS Tables. Each table contains 128 maximum dialing assignments for the selected dialing plan.
Page 396

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 3-03 Trunk-to-Trunk Group Assignment 4-40 LCR Class Selection 1-1-30 Route Advance Block Assignment 1-8-08 Class of Service (Station) Feature Selection 2 1-14-00 ARS Allow/Deny Selection 1-14-02...
Page 397: Ars Dial Allow/deny Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-14-02 ARS Dial Allow/Deny Selection System Mode General Description Submode Use this Memory Block to specify whether or not to Allow digits that are entered in the ARS dialing assignment to be routed using the ARS feature.
Page 398

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-14-03 ARS Route Table Number Assignment 1-14-04 ARS Trunk Group to Route Number Assignment 1-14-05 ARS Digit Delete Assignment 1-14-06 ARS Digit Add Assignment Notes Entries A0~C8 are 100~128.
Page 399: Ars Route Table Number Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-14-03 ARS Route Table Number Assignment System Mode General Description Submode Use this Memory Block to assign each ARS Dialing Assignment to an ARS Route Assignment. Data No. Display S e t t i n g...
Page 400

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-14-06 ARS Digit Add Assignment Notes Entries A0~C8 are 100~128. When ARS Route Assignment 00 is selected, the call is sent to Trunk Group 01 exactly as it was dialed.
Page 401: Ars Trunk Group To Route Number Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-14-04 ARS Trunk Group to Route Number System Mode Assignment Submode General Description Use this Memory Block to specify whether a Trunk Group, Route Advance Block, or Data No. ICM is used for each Route assignment.
Page 402

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-14-01 ARS Dialing Assignment 1-14-02 ARS Dial Allow/Deny Selection 1-14-03 ARS Route Table Number Assignment 1-14-05 ARS Digit Delete Assignment 1-14-06 ARS Digit Add Assignment 1-14-07...
Page 403: Ars Digit Delete Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-14-05 ARS Digit Delete Assignment System Mode General Description Submode Use this Memory Block to specify the number of digits to delete from the Route assignment. Data No. Display D a t a...
Page 404

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 3-03 Trunk-to-Trunk Group Assignment 4-40 LCR Class Selection 1-1-30 Route Advance Block Assignment 1-8-08 Class of Service (Station) Feature Selection 2 1-14-00 ARS Allow/Deny Selection 1-14-01...
Page 405: Ars Digit Add Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-14-06 ARS Digit Add Assignment System Mode General Description Submode Use this Memory Block to specify the number of digits to add to the Route assignment. Display Data No. S e t t i n g...
Page 406

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-14-04 ARS Trunk Group to Route Number Assignment 1-14-05 ARS Digit Delete Assignment 1-14-07 ARS Max Digit Assignment Notes A maximum of 10 digits can be added to a route assignment.
Page 407: Ars Max Digit Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-14-07 ARS Max Digit Assignment System Mode General Description Submode Use this Memory Block to specify the number of digits to be collected by the system before the message is sent to the network.
Page 408

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Notes When 00 is set for this Memory Block, refer to Memory Block 1-1-81 (ISDN / K-CCIS Interval Time Selection) for the time it takes before the message is sent to the K-CCIS Network.
Page 409

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ THIS PAGE INTENTIONALLY LEFT BLANK ___________________________________________________________________________________ 2 - 332 Memory Blocks...
Page 410: K-ccis Main/remote Office Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-15-00 K-CCIS Main/Remote Office Selection System Mode General Description Submode Use this Memory Block to activate CCIS by assigning a Main or Remote system. Display Data No. S e t t i n g...
Page 411

SMDR Telephone Print Selection Notes For Electra Elite IPK-to-Electra Elite IPK Network only one system can be set for Main. All other systems must be set from Remote. When connected to a PBX, the Electra Elite IPK must be set for REMOTE in this Memory Block.
Page 412: Common Signal Channel Data Speed Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-15-01 Common Signal Channel Data Speed System Mode Assignment Submode General Description Use this Memory Block to assign the Data Transmission speed for each Common Data No. Signaling channel. DisplayS PC Programming D a t a S e t t i n g N o .
Page 413

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name Card Interface Slot Assignment 7-3-01 MIF (LCR) Assignment 7-3-02 MIF (SMDR) Assignment 1-15-00 K-CCIS Main/Remote Office Selection 1-15-02 Common Signal Channel Assignment 1-15-03 Originating Point Code Assignment...
Page 414: Common Signal Channel Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-15-02 Common Signal Channel Assignment System Mode General Description Submode Use this Memory Block to assign a T1 Trunk to be a Common Signaling Channel. Display Data No. D a t a C - C h a n n e l...
Page 415

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming (Continued) M.B. Number Memory Block Name 1-15-10 Calling Name Display Allow/Deny Selection 1-15-11 Centralized Billing Allow/Deny Selection 1-15-12 Centralized Billing – Point Code of Center Office Assignment 1-15-13 Centralized Day/Night Switching for Remote Office Assignment...
Page 416: Originating Point Code Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-15-03 Originating Point Code Assignment System Mode General Description Submode Use this Memory Block to assign the originating point code for each Common Signaling Channel. Data No. Display D a t a C - C h a n n e l...
Page 417

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming (Continued) M.B. Number Memory Block Name 1-15-09 K-CCIS Maximum Call Forwarding Hop Assignment 1-15-10 Calling Name Display Allow/Deny Selection 1-15-11 Centralized Billing Allow/Deny Selection 1-15-12 Centralized Billing – Point Code of Center Office Assignment...
Page 418: Destination Point Code Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-15-04 Destination Point Code Assignment System Mode General Description Submode Use this Memory Block to assign the Destination Point Code for each Common Signaling Channel. Data No. Display D a t a C - C h a n n e l...
Page 419

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming (Continued) M.B. Number Memory Block Name 1-15-08 Link Reconnect Allow/Deny Selection 1-15-09 K-CCIS Maximum Call Forwarding Hop Assignment 1-15-10 Calling Name Display Allow/Deny Selection 1-15-11 Centralized Billing Allow/Deny Selection 1-15-12 Centralized Billing – Point Code of Center Office Assignment...
Page 420: Destination Point Code Transfer Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-15-05 Destination Point Code Transfer System Mode Assignment Submode General Description Use this Memory Block to assign the Destination Point Code to the associated Data No. Common Signaling Channel when K-CCIS commands are required to pass through a tandem system.
Page 421

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Example: Elite 100 is Master for Centralized Day/Night Mode Change (K-CCIS). Electra Elite IPK Electra Elite IPK Electra Elite IPK 10 TG 10 CCIS CCIS Cabinet 1 Cabinet 1 Cabinet 1 Cabinet 1...
Page 422

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Related Programming (Continued) M.B. Number Memory Block Name 1-15-13 Centralized Day/Night Switching for Remote Office Assignment 1-15-14 Centralized Day/Night Switching for Main Office Assignment 1-15-15 Centralized BLF Send Point Code Assignment 1-15-16 Centralized BLF Send Extension Number Assignment...
Page 423: Originating Office Code Number Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-15-06 Originating Office Code Number System Mode Assignment Submode General Description Use this Memory Block to assign the Office Code to the system when Open Data No. Numbering Plan is used. Display PC Programming...
Page 424

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Related Programming (Continued) M.B. Number Memory Block Name 1-15-05 Destination Point Code Transfer Assignment 1-15-07 K-CCIS Message Response Timeout Assignment 1-15-08 Link Reconnect Allow/Deny Selection 1-15-09 K-CCIS Maximum Call Forwarding Hop Assignment 1-15-10...
Page 425: K-ccis Message Response Timeout Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-15-07 K-CCIS Message Response Timeout System Mode Assignment Submode General Description Use this Memory Block to assign the time before a call or message request is Data No. canceled when no response is received from the destination office.
Page 426

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Related Programming (Continued) M.B. Number Memory Block Name 1-15-05 Destination Point Code Transfer Assignment 1-15-06 Originating Office Code Number Assignment 1-15-08 Link Reconnect Allow/Deny Selection 1-15-09 K-CCIS Maximum Call Forwarding Hop Assignment 1-15-10...
Page 427: Link Reconnect Allow/deny Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-15-08 Link Reconnect Allow/Deny Selection System Mode General Description Submode Use this Memory Block to allow or deny the Link Reconnect feature. Display Data No. D a t a S e t t i n g N o .
Page 428

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Related Programming (Continued) M.B. Number Memory Block Name 1-15-10 Calling Name Display Allow/Deny Selection 1-15-11 Centralized Billing Allow/Deny Selection 1-15-12 Centralized Billing – Point Code of Center Office Assignment 1-15-13 Centralized Day/Night Switching for Remote Office Assignment...
Page 429: K-ccis Maximum Call Forwarding Hop Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-15-09 K-CCIS Maximum Call Forwarding System Mode Hop Assignment Submode General Description Use this Memory Block to specify the maximum number of multiple Call Forwarding Data No. hops over the CCIS network. Display...
Page 430

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Related Programming (Continued) M.B. Number Memory Block Name 1-15-07 K-CCIS Message Response Timeout Assignment 1-15-08 Link Reconnect Allow/Deny Selection 1-15-10 Calling Name Display Allow/Deny Selection 1-15-11 Centralized Billing Allow/Deny Selection 1-15-12 Centralized Billing – Point Code of Center Office Assignment...
Page 431: Calling Name Display Allow/deny Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-15-10 Calling Name Display Allow/Deny System Mode Selection Submode General Description Use this Memory Block per Common Signaling Channel to allow or deny sending the Data No. station name. Display PC Programming D a t a...
Page 432

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Related Programming (Continued) M.B. Number Memory Block Name 1-15-07 K-CCIS Message Response Timeout Assignment 1-15-08 Link Reconnect Allow/Deny Selection 1-15-09 K-CCIS Maximum Call Forwarding Hop Assignment 1-15-11 Centralized Billing Allow/Deny Selection 1-15-12 Centralized Billing – Point Code of Center Office Assignment...
Page 433: Centralized Billing Allow/deny Selection

Selection Submode General Description Use this Memory Block to assign the Electra Elite IPK to send billing to the Billing Data No. Center Office (NEAX2000/2400) across the K-CCIS network. Electra Elite IPK does not support receiving and managing billing information.
Page 434

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Related Programming (Continued) M.B. Number Memory Block Name 1-15-06 Originating Office Code Number Assignment 1-15-07 K-CCIS Message Response Timeout Assignment 1-15-08 Link Reconnect Allow/Deny Selection 1-15-09 K-CCIS Maximum Call Forwarding Hop Assignment 1-15-10...
Page 435: Centralized Billing – Point Code Of Center Office Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-15-12 Centralized Billing – Point Code of System Mode Center Office Assignment Submode General Description Use this Memory Block to assign the Common Signaling Channel number and point Data No. code of the Billing Center Office (NEAX2000/2400).
Page 436

SMDR Telephone Print Selection Notes The Electra Elite IPK can be only a Remote Office for a NEAX2000/2400 Billing Center Office. When the Electra Elite IPK is a tandem office and Billing Information is not required, this assignment is not necessary. ___________________________________________________________________________________...
Page 437: Centralized Day/night Switching For Remote Office Assignment

1-15-13 Centralized Day/Night Switching for System Mode Remote Office Assignment Submode General Description Use this Memory Block to assign the Electra Elite IPK to switch Day/Night mode when Data No. it receives the command from a main office. Display PC Programming...
Page 438

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Related Programming (Continued) M.B. Number Memory Block Name 1-15-07 K-CCIS Message Response Timeout Assignment 1-15-08 Link Reconnect Allow/Deny Selection 1-15-09 K-CCIS Maximum Call Forwarding Hop Assignment 1-15-10 Calling Name Display Allow/Deny Selection 1-15-11...
Page 439: Centralized Day/night Switching For Main Office Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-15-14 Centralized Day/Night Switching for System Mode Main Office Assignment Submode General Description Use this Memory Block to assign the Point Codes and the CCH Channel to control Data No. remote systems for Centralized Day/Night Switching.
Page 440

This Memory Block is used for the Main Office only. Up to 16 Remote Offices can be controlled by a Main Office. The Electra Elite IPK cannot be a Main Office for a NEAX2000/2400 PBX. ___________________________________________________________________________________ Programming Manual 2 - 363...
Page 441: Centralized Blf Send Point Code Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-15-15 Centralized BLF Send Point System Mode Code Assignment Submode General Description Use this Memory Block to assign the Destination Point Codes and the CCH Channel Data No. of systems to be sent Centralized BLF messages. A CCH Channel of i can be assigned for K-CCIS over IP.
Page 442

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Related Programming (Continued) M.B. Number Memory Block Name 1-15-03 Originating Point Code Assignment 1-15-04 Destination Point Code Assignment 1-15-05 Destination Point Code Transfer Assignment 1-15-06 Originating Office Code Number Assignment 1-15-07 K-CCIS Message Response Timeout Assignment...
Page 443: Centralized Blf Send Extension Number Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-15-16 Centralized BLF Send Extension System Mode Number Assignment Submode General Description Use this Memory Block to assign the Extension Numbers for sending Centralized BLF Data No. messages. R1500 or higher is required.
Page 444

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name Card Interface Slot Assignment 1-8-08 Class of Service (Station) Feature Selection 2 (Page 6, LK 2) 1-15-00 K-CCIS Main/Remote Office Selection 1-15-01 Common Signal Channel Data Speed Assignment...
Page 445: Centralized Blf Send Time Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-15-17 Centralized BLF Send Time System Mode Assignment Submode General Description Use this Memory Block to assign the time interval for sending BLF information across Data No. the K-CCIS Network. R1500 or higher is required.
Page 446

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Related Programming (Continued) M.B. Number Memory Block Name 1-15-05 Destination Point Code Transfer Assignment 1-15-06 Originating Office Code Number Assignment 1-15-07 K-CCIS Message Response Timeout Assignment 1-15-08 Link Reconnect Allow/Deny Selection 1-15-09 K-CCIS Maximum Call Forwarding Hop Assignment...
Page 447: Centralized Blf Receive Extension Number Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 1-15-18 Centralized BLF Receive Extension System Mode Number Assignment Submode General Description Use this Memory Block to assign the Extension Numbers of remote systems to receive Data No. Centralized BLF messages. R1500 or higher is required.
Page 448

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Related Programming (Continued) M.B. Number Memory Block Name 1-15-03 Originating Point Code Assignment 1-15-04 Destination Point Code Assignment 1-15-05 Destination Point Code Transfer Assignment 1-15-06 Originating Office Code Number Assignment 1-15-07 K-CCIS Message Response Timeout Assignment...
Page 449: Centralized 911 Allow/deny Selection

General Description Submode Use this Memory Block to assign the Electra Elite IPK installed as a Main Office to send the Calling Party Number out the CAMA trunk when an emergency 911 call is originated from a remote K-CCIS office.
Page 450

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Notes Assign this Memory Block to YS (Allow) at the Main Office and all tandem offices to allow the Calling Party Number to be sent out on the CAMA or an ISDN PRI trunk when a 911 call is received from a remote K-CCIS system.
Page 451: Centralized 911/calling Party (cpn) Originating Number Selection

Originating Number Selection Submode General Description Use this Memory Block to assign the Electra Elite IPK installed as a Remote K-CCIS Data No. Office to send the Station Number or CES-ID or Calling Party Number for Calling Party Number information to the Main Office when an Emergency 911 call is originated.
Page 452

Use this Memory Block for 911 outgoing calls from a remote office to select Station Number or CES-ID for Calling Party Number information. When the main office is a NEAX2000 or Electra Elite IPK, this data is set to CES-ID.
Page 453: Centralized 911 Look Ahead Routing Allow/ Deny Selection

Allow/ Deny Selection Submode General Description Use this Memory Block to assign the Electra Elite IPK installed at a remote K-CCIS Data No. office to allow an alternate line to be used when all trunks at the main office are busy when an Emergency 911 call is originated at the remote K-CCIS office.
Page 454

Block 1-8-44. When an RAB is assigned in Memory Block 1-8-43, and a Centralized 911 call is originated, the Electra Elite IPK searches for an idle line in the TG that has lower priority in the route advance block assigned in Memory Block 1-8-43, and then searches for an idle line in the trunk group/route advance block assigned in Memory Block 1-8-44.
Page 455

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ THIS PAGE INTENTIONALLY LEFT BLANK ___________________________________________________________________________________ 2 - 378 Memory Blocks...
Page 456: Auto Negotiation Yes/no Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-16-00 Auto Negotiation Yes/No Selection System Mode General Description Submode Use this Memory Block to specify whether or not Auto Negotiation is enabled for each port of the HUB(8)-U( ) ETU. When No is selected, Memory Block 1-16-01 (Port Speed Selection 10/100 Base -T) and Memory Block 1-16-02 (Port Duplex Mode Data No.
Page 457

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name Card Interface Slot Selection 1-16-01 Port Speed Selection – 10/100 Base T 1-16-02 Port Duplex Mode Selection 1-16-03 MDI/MDIX Mode Selection 1-16-04 VLAN Mode Selection 1-16-05...
Page 458: Port Speed Selection – 10/100 Base-t

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-16-01 Port Speed Selection – 10/100 Base-T System Mode General Description Submode When Memory Block 1-16-00 (Auto Negotiation Yes/No Selection) is set to NO, use this Memory Block to specify the Ethernet port speed as 10 Mbps or 100 Mbps for each port of each HUB(8)-U( ) ETU.
Page 459

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name Card Interface Slot Selection 1-16-00 Auto Negotiation Yes/No Selection 1-16-02 Port Duplex Mode Selection 1-16-03 MDI/MDIX Mode Selection 1-16-04 VLAN Mode Selection 1-16-05 Default VLAN ID Tag Insertion Assignment...
Page 460: Port Duplex Mode Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-16-02 Port Duplex Mode Selection System Mode General Description Submode When Memory Block 1-16-00 (Auto Negotiation Yes/No Selection) is set to NO, use this Memory Block to specify duplex mode (HALF or FULL) for each port of each HUB(8)-U( ) ETU.
Page 461

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name Card Interface Slot Selection 1-16-00 Auto Negotiation Yes/No Selection 1-16-01 Port Speed Selection – 10/100 Base T 1-16-03 MDI/MDIX Mode Selection 1-16-04 VLAN Mode Selection 1-16-05...
Page 462: Mdi/mdix Mode Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-16-03 MDI/MDIX Mode Selection System Mode General Description Submode Use this Memory Block to specify an MDI/MDIX mode for each port of each HUB(8)-U( ) ETU. Data No. R1500 or higher is required.
Page 463

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name Card Interface Slot Selection 1-16-00 Auto Negotiation Yes/No Selection 1-16-01 Port Speed Selection – 10/100 Base T 1-16-02 Port Duplex Mode Selection 1-16-04 VLAN Mode Selection...
Page 464: Vlan Mode Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-16-04 VLAN Mode Selection System Mode General Description Submode Use this Memory Block to specify whether or not IEEE 802.1q VLAN Tagging is enabled for each HUB(8)-U( ) ETU. This Memory Block must also be enabled to use IEEE 802.p Priority.
Page 465

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name Card Interface Slot Selection 1-16-00 Auto Negotiation Yes/No Selection 1-16-01 Port Speed Selection – 10/100 Base T 1-16-02 Port Duplex Mode Selection 1-16-03 MDI/MDIX Mode Selection...
Page 466: Default Vlan Id Tag Insertion Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-16-05 Default VLAN ID Tag Insertion System Mode Assignment Submode General Description Use this Memory Block to insert VLAN ID tagging to data frames from network devices Data No. that cannot insert VLAN tags. When data without a VLAN tag is transmitted by the device on the port, a tag is inserted with the VLAN ID assigned by this Memory Block.
Page 467

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name Card Interface Slot Selection 1-16-00 Auto Negotiation Yes/No Selection 1-16-01 Port Speed Selection – 10/100 Base T 1-16-02 Port Duplex Mode Selection 1-16-03 MDI/MDIX Mode Selection...
Page 468: Port Based Priority Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-16-06 Port Based Priority Selection System Mode General Description Submode Use this memory block to specify how frames, reaching the ingress port without VLAN tags are marked for queuing internally in the HUB(8). The HUB(8) has two queues: High Priority and Low Priority.
Page 469

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name Card Interface Slot Selection 1-16-00 Auto Negotiation Yes/No Selection 1-16-01 Port Speed Selection – 10/100 Base T 1-16-02 Port Duplex Mode Selection 1-16-03 MDI/MDIX Mode Selection...
Page 470: High Priority Rx Tag Threshold

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-16-07 High Priority RX Tag Threshold System Mode General Description Submode The HUB(8) has two queues: High Priority and Low Priority. When Memory Block 1-16-06 is set to NO, and the priority of the VLAN tag is equal to or greater than the setting in this block, the tag is queued for high priority.
Page 471

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name Card Interface Slot Selection 1-16-00 Auto Negotiation Yes/No Selection 1-16-01 Port Speed Selection – 10/100 Base T 1-16-02 Port Duplex Mode Selection 1-16-03 MDI/MDIX Mode Selection...
Page 472: High Priority Tx Tag Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-16-08 High Priority TX Tag Assignment System Mode General Description Submode For frames marked at the ingress port by Memory Block 1-16-06 as High Priority, this memory block setting on the egress port assigns a value (0 ~7) to the priority field of the VLAN tag.
Page 473

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name Card Interface Slot Selection 1-16-00 Auto Negotiation Yes/No Selection 1-16-01 Port Speed Selection – 10/100 Base T 1-16-02 Port Duplex Mode Selection 1-16-03 MDI/MDIX Mode Selection...
Page 474: Low Priority Tx Tag Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-16-09 Low Priority TX Tag Assignment System Mode System Mode General Description Submode Submode For frames marked at the ingress port by Memory Block 1-16-06 as Low Priority, this memory block setting on the egress port assigns a value (0 ~7) to the priority field of the VLAN tag.
Page 475

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name Card Interface Slot Selection 1-16-00 Auto Negotiation Yes/No Selection 1-16-01 Port Speed Selection – 10/100 Base T 1-16-02 Port Duplex Mode Selection 1-16-03 MDI/MDIX Mode Selection...
Page 476: Port Mirroring Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-16-10 Port Mirroring Selection System Mode General Description Submode Use this Memory Block to specify whether or not Port Mirroring is enabled for each HUB(8)-U( ) ETU. The source port and the target port must be members of the same VLAN(s).
Page 477

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name Card Interface Slot Selection 1-16-00 Auto Negotiation Yes/No Selection 1-16-01 Port Speed Selection – 10/100 Base T 1-16-02 Port Duplex Mode Selection 1-16-03 MDI/MDIX Mode Selection...
Page 478: Mirroring Source Port Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-16-11 Mirroring Source Port Assignment System Mode General Description Submode When Port Mirroring is enabled in Memory Block 1-16-10 (Port Mirroring Selection), use this Memory Block to specify a port with data to be monitored on another port specified by Memory Block 1-16-12 (Mirroring Target Port Assigment) for each Data No.
Page 479

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name Card Interface Slot Selection 1-16-00 Auto Negotiation Yes/No Selection 1-16-01 Port Speed Selection – 10/100 Base T 1-16-02 Port Duplex Mode Selection 1-16-03 MDI/MDIX Mode Selection...
Page 480: Mirroring Target Port Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-16-12 Mirroring Target Port Assignment System Mode General Description Submode When Port Mirroring is enabled in Memory Block 1-16-10 (Port Mirroring Selection), use this Memory Block to specify a target port that monitors frames transmitted on the source port specified by Memory Block 1-16-11 (Mirroring Source Port Assigment) for Data No.
Page 481

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name Card Interface Slot Selection 1-16-00 Auto Negotiation Yes/No Selection 1-16-01 Port Speed Selection – 10/100 Base T 1-16-02 Port Duplex Mode Selection 1-16-03 MDI/MDIX Mode Selection...
Page 482: Vlan Group To Vlan Id Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-16-13 VLAN Group to VLAN ID Assignment System Mode General Description Submode Use this Memory Block to create a list of valid VLAN IDs to be recognized by the HUB(8)-U( ) ETU. Data No.
Page 483

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name Card Interface Slot Selection 1-16-00 Auto Negotiation Yes/No Selection 1-16-01 Port Speed Selection – 10/100 Base T 1-16-02 Port Duplex Mode Selection 1-16-03 MDI/MDIX Mode Selection...
Page 484: Port Vlan Group Membership

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-16-14 Port VLAN Group Membership System Mode General Description Submode Use this Memory Block to create a list of accepted VLANs for each port. When Memory Block 1-16-04 (VLAN Mode Selection) is set to YS, each port accepts frames tagged with VLAN IDs only when the port is programmed as a member of that Data No.
Page 485

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name Card Interface Slot Selection 1-16-00 Auto Negotiation Yes/No Selection 1-16-01 Port Speed Selection – 10/100 Base T 1-16-02 Port Duplex Mode Selection 1-16-03 MDI/MDIX Mode Selection...
Page 486: Vlan Tag Insertion Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-16-15 VLAN Tag Insertion Selection System Mode General Description Submode Use this Memory Block to specify whether or not the port should insert VLAN tags in frames transmitted on this port. When this Memory Block is set to NO, tags are deleted from frames of the same VLAN Group transmitted on this port.
Page 487

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name Card Interface Slot Selection 1-16-00 Auto Negotiation Yes/No Selection 1-16-01 Port Speed Selection – 10/100 Base T 1-16-02 Port Duplex Mode Selection 1-16-03 MDI/MDIX Mode Selection...
Page 488: Flow Control For Full Duplex Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-16-16 Flow Control for Full Duplex System Mode Selection Submode General Description Use this Memory Block to specify whether or not Full duplex IEEE802.3x Flow Control Data No. is enabled for each HUB(8)-U( ) ETU port.
Page 489

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name Card Interface Slot Selection 1-16-00 Auto Negotiation Yes/No Selection 1-16-01 Port Speed Selection – 10/100 Base T 1-16-02 Port Duplex Mode Selection 1-16-03 MDI/MDIX Mode Selection...
Page 490: Back Pressure For Half Duplex

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 1-16-17 Back Pressure for Half Duplex System Mode General Description Submode Use this Memory Block to specify whether or not half-duplex Back Pressure Flow Control is enabled for each HUB(8)-U( ) ETU port.
Page 491

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name Card Interface Slot Selection 1-16-00 Auto Negotiation Yes/No Selection 1-16-01 Port Speed Selection – 10/100 Base T 1-16-02 Port Duplex Mode Selection 1-16-03 MDI/MDIX Mode Selection...
Page 492: Trunk To Tenant Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 2-01 Trunk to Tenant Assignment Tenant Mode General Description Submode Use this Memory Block to assign CO/PBX lines to a tenant. — Display Data No. T e n a n t N o .
Page 493

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Programming Procedures 1 Go off-line. 2 Press LK2 to access the Memory Block. 3 Press the corresponding CO/PBX line key to change the data option. Default Values Tenant 00 = All trunks are assigned...
Page 494: Line Key Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 2-05 Line Key Selection Tenant Mode General Description Submode Use this Memory Block to select Tenant-Wide Mode or Telephone Mode line key — assignment for each tenant. Data No. Display T e n a n t N o .
Page 495: Line Key Selection For Tenant Mode

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 2-06 Line Key Selection for Tenant Mode Tenant Mode General Description Submode Use this Memory Block to assign functions to each CO/PBX line key on each — telephone in a tenant specified as Tenant Mode in Memory Block 2-05 (Line Key Selection).
Page 496

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Programming Procedures 7 The operation data includes: Default Values Setting Data Page 1 Tenant 00 = CO/PBX Lines 01~08 Tenant 01~ 47 = Not Assigned Line Setting Data (1) Setting Data (2) Indication...
Page 497

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Notes Specify Call Appearance as the call appearance number of Call Appearance Block numbers from Memory Block 4-43 (Station to Call Appearance Block Assignment). Use this Memory Block to assign the following functions to each of the CO/PBX line keys on each telephone in a...
Page 498: System Speed Dial Display Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 2-07 System Speed Dial Display Tenant Mode Assignment Submode — General Description Use this Memory Block to specify whether or not confirmation of the Speed Dial Data No. numbers and messages stored in the system Speed Dial memory is allowed.
Page 499

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Programming Procedures (Continued) 3 Press the CO/PBX Line key. The LED indication changes to indicate the data Default Values each time the CO/PBX line key is pressed. All Speed Dial confirmation allowed Use the following to enter data:...
Page 500: Ecr Relay To Tenant Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 2-08 ECR Relay to Tenant Assignment Tenant Mode General Description Submode Use this Memory Block to specify Tenant Assignment for External Tone Ring/Night — Chime function. Data No. Display T e n a n t D a t a N o .
Page 501: Did Limit To Tenant Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 2-09 DID Limit to Tenant Assignment System Mode General Description Submode Use this Memory Block to assign the number of DID calls allowed to ring at a specified — tenant. Data No. Display...
Page 502: Trunk Name/number Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 3-00 Trunk Name/Number Assignment CO/PBX Line Mode General Description Submode Use this Memory Block to specify telephone name/number for the CO/PBX line that is — displayed when the CO/PBX Line is seized, or during an incoming call.
Page 503: Trunk Status Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 3-02 Trunk Status Selection CO/PBX Line Mode Use this Memory Block to specify whether a CO/PBX line is used for call origination Submode and termination or termination only. — Display Data No. C O / P B X D a t a N o .
Page 504: Trunk-to-trunk Group Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 3-03 Trunk-to-Trunk Group Assignment CO/PBX Line Mode General Description Submode Use this Memory Block to assign a Trunk Group Number (01~32) to each CO/PBX — line. Data No. Display C O / P B X N o .
Page 505: Trunk-to-trunk Transfer Yes/no Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 3-04 Trunk-to-Trunk Transfer Yes/No CO/PBX Line Mode Selection Submode — General Description Use this Memory Block to specify whether or not to allow Trunk-to-Trunk Transfer. Data No. Display C O / P B X...
Page 506

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-8-07 Class of Service (Attendant) Feature Selection 1 1-8-08 Class of Service (Station) Feature Selection 2 3-05 Trunk Incoming Answer Mode Selection 3-06 Automatic Tandem Trunk Assignment...
Page 507: Trunk Incoming Answer Mode Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 3-05 Trunk Incoming Answer Mode CO/PBX Line Mode Selection Submode — General Description Use this Memory Block to specify the incoming answer mode (Automatic Data No. Trunk-to-Trunk Transfer, Automated Attendant, or DISA) per outside line.
Page 508

Document Revision 4 ___________________________________________________________________________________ Related Programming Refer to individual features in the Electra Elite IPK Features and Specifications Manual. Notes Only trunks assigned to TANDM TRF in this Memory Block are set or canceled for Automatic Trunk-to-Trunk Transfer Mode when an attendant position enters 00 during the set or cancel operation.
Page 509: Automatic Tandem Trunk Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 3-06 Automatic Tandem Trunk Assignment CO/PBX Line Mode Use this Memory Block to specify the incoming trunk and outgoing trunk for Automatic Submode Trunk-to-Trunk Transfer. — Display Data No. ( I n c o m i n g )
Page 510: Co/pbx Ringing Variation Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 3-07 CO/PBX Ringing Variation Selection CO/PBX Line Mode General Description Submode Use this Memory Block to specify a ringing tone for each CO/PBX line. — Display Data No. C O / P B X...
Page 511: Co External Source Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 3-11 CO External Source Selection CO/PBX Line Mode General Description Submode Use this Memory Block to specify whether the Music On Hold source is from the CO or — an external source (EXT SOURCE).
Page 512: Trunk-to-moh Trunk Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 3-12 Trunk-to-MOH Trunk Assignment CO/PBX Line Mode General Description Submode Use this Memory Block to specify the music on hold source for each CO/PBX line. — Display Data No. C O / P B X...
Page 513: Tie Line Type Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 3-14 Tie Line Type Assignment CO/PBX Line Mode General Description Submode Use this Memory Block to assign the loop supervision to be used for each Trunk — associated with a Tie line. Data No.
Page 514

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Notes Line keys 1~4 identify the following methods of loop supervision: 1 = Second Dial Tone 2 = Immediate Start 3 = Delay Dial 4 = Wink Start This Memory Block affects T1 channels assigned as Tie lines.
Page 515: Trunk Dtmf Duration/interdigit Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 3-15 Trunk DTMF Duration/Interdigit CO/PBX Line Mode Selection Submode — General Description Use this Memory Block to specify the tone duration/interdigit time of dual-tone Data No. multifrequency (DTMF) signals. Display PC Programming +BCT C O / P B X N o .
Page 516

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Notes This is also used for Tie lines. This Memory Block affects T1 Channels assigned as Tie/DID lines. A DTI-U( ) ETU is required. ___________________________________________________________________________________ Programming Manual 2 - 439...
Page 517: Tie Line Prepause Time Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 3-16 Tie Line Prepause Time Selection CO/PBX Line Mode General Description Submode Use this Memory Block to specify the time (prepause) before the originating side can — send dial pulse or dual-tone multifrequency (DTMF) to the distant system.
Page 518: Tie Line Answer Detect Time Selection

Tie Line Answer Detect Time CO/PBX Line Mode Selection Submode — General Description Use this Memory Block to specify the time before an Electra Elite IPK system answer Data No. (off-hook) is recognized as an answer. Display PC Programming +ALM...
Page 519: Tie Line Release Detect Time Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 3-18 Tie Line Release Detect Time CO/PBX Line Mode Selection Submode — General Description Use this Memory Block to specify the time before the circuit disconnect detected on Data No. the Tie line on the distant system side is recognized as Tie line release.
Page 520

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Notes Specify distinguishing circuit release from on-hook, noise, and temporary interruption. Probable situations for Tie line release detection include: Called side hangs up first. The circuit is released 92 ms. + specified time after the other party disconnects the call.
Page 521: Tie Line/co/pbx Incoming Signal Detect Time Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 3-19 Tie Line/CO/PBX Incoming Signal CO/PBX Line Mode Detect Time Selection Submode — General Description Use this Memory Block to specify the time after the incoming signal from another Data No. system is detected before the acknowledge signal is sent out.
Page 522

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Programming Procedures 3 Press the corresponding CO/PBX line key to change incoming signal detect time for CO/PBX No. Receiving Side Incoming Signal Detection DC Loop Supervision Time Sending Acknowledgment Signal Use the following to enter data:...
Page 523: Tie Line Loop Off-guard Time Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 3-20 Tie Line Loop Off-Guard Time CO/PBX Line Mode Selection Submode — General Description Use this Memory Block to assign loop off-guard time to prevent noise that could cause Data No. the system to be unable to answer an incoming Tie line.
Page 524

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Notes Assign a loop off-guard time to prevent system malfunction caused by noise when going off-hook to answer a call from another system on a Tie line call. The system ignores any noise that is detected during the time specified in this Memory Block.
Page 525: Tie Line Length Of Wink Signal Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 3-21 Tie Line Length of Wink Signal CO/PBX Line Mode Selection Submode — General Description Use this Memory Block to specify the time a wink pulse is sent to another system. Data No.
Page 526

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Programming Procedures (Continued) 5 Program the next Memory Block or press to go back on-line. Notes Specify Wink Start in Memory Block 3-14 (Tie Line Type Assignment). This Memory Block affects T1 channels assigned as Tie/DID lines.
Page 527: Tie Line Length Of Delay Signal Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 3-22 Tie Line Length of Delay Signal CO/PBX Line Mode Selection Submode — General Description Use this Memory Block to specify the time a delay pulse is sent to another system. Data No.
Page 528

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Notes Specify Delay loop supervision in Memory Block 3-14 (Tie Line Type Assignment). This Memory Block affects T1 channels assigned as Tie/DID lines. ___________________________________________________________________________________ Programming Manual 2 - 451...
Page 529: Tie Line Incoming Interdigit Timeout Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 3-24 Tie Line Incoming Interdigit Timeout CO/PBX Line Mode Selection Submode — General Description Use this Memory Block to specify the time, in seconds, that an address signal is Data No. missing during the incoming call detection process before an error tone is returned to the other system.
Page 530

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Notes A timeout occurs when: A dial pulse is not received within the time specified by this Memory Block after the receiving side detects the off-hook signal. The next dial pulse is not received within the time specified by this Memory Block after the receiving side detects (receives) a dial pulse.
Page 531: Tie Line Wink/delay Signal Detect Timeout Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 3-25 Tie Line Wink/Delay Signal Detect CO/PBX Line Mode Timeout Selection Submode — General Description Use this Memory Block to specify a maximum time, in seconds, for receiving an Data No. acknowledgment signal from a distant system before sending a busy tone.
Page 532

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Programming Procedures (Continued) 3 Press the corresponding CO/PBX line key to change signal detect timeout for CO/PBX No. Originating Side Sending an Outgoing Signal Time Receiving Acknowledgment Signal Timeout when acknowledgment signal is not received.
Page 533: Tie Line Dial Tone Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 3-27 Tie Line Dial Tone Selection CO/PBX Line Mode General Description Submode Use this Memory Block to specify whether or not to send a dial tone to the distant — system. Data No.
Page 534: Tie Line Reorder Tone Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 3-28 Tie Line Reorder Tone Selection CO/PBX Line Mode General Description Submode Use this Memory Block to specify whether or not to send a reorder tone to the — originating station when the number of a distant system is used to originate a call over a Tie line.
Page 535

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 3-14 Tie Line Type Assignment Notes This Memory Block affects T1 channels assigned as Tie lines. ___________________________________________________________________________________ 2 - 458 Memory Blocks...
Page 536: Trunk Internal Transmit Pad Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 3-29 Trunk Internal Transmit Pad CO/PBX Line Mode Selection Submode — General Description Use this Memory Block to specify a dB volume level for calls originated from the Data No. extensions of a local system to a distant system.
Page 537

Electra Elite IPK ___________________________________________________________________________________ Notes The Electra Elite IPK system divides the connections into the following patterns: (Specify the sending and receiving levels of each pattern for each of the trunks.) Connections established between the intercom stations of the Pattern A (Intercom Mode) local system and trunks.
Page 538: Trunk Internal Receive Pad Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 3-30 Trunk Internal Receive Pad Selection CO/PBX Line Mode General Description Submode Use this Memory Block to specify a dB volume level for calls coming to extensions of a — local system from a distant system.
Page 539

Electra Elite IPK ___________________________________________________________________________________ Notes The Electra Elite IPK system divides the connections into the following patterns: (Specify the sending and receiving levels of each pattern for each of the trunks.) Connections established between the intercom stations of the Pattern A (Intercom Mode) local system and trunks.
Page 540: Trunk External Transmit Pad Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 3-31 Trunk External Transmit Pad CO/PBX Line Mode Selection Submode — General Description Use this Memory Block to specify transmit dB volume level for tandem calls between a Data No. local system and two distant systems.
Page 541

Electra Elite IPK ___________________________________________________________________________________ Notes The Electra Elite IPK system divides the connections into the following patterns: (Specify the sending and receiving levels of each pattern for each of the trunks.) Connections established between the intercom stations of the Pattern A (Intercom Mode) local system and trunks.
Page 542: Trunk External Receive Pad Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 3-32 Trunk External Receive Pad Selection CO/PBX Line Mode General Description Submode Use this Memory Block to specify receive dB volume level for tandem calls between a — local system and two distant systems.
Page 543

Electra Elite IPK ___________________________________________________________________________________ Notes The Electra Elite IPK system divides the connections into the following patterns: (Specify the sending and receiving levels of each pattern for each of the trunks.) Connections established between the intercom stations of the Pattern A (Intercom Mode) local system and trunks.
Page 544: Disconnect Recognition Time Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 3-33 Disconnect Recognition Time CO/PBX Line Mode Selection Submode — General Description Use this Memory Block to specify the minimum time before a disconnected circuit can Data No. be accessed again. Display PC Programming...
Page 545: Automated Attendant Message To Trunk Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 3-38 Automated Attendant Message to CO/PBX Line Mode Trunk Selection Submode — General Description Use this Memory Block to assign the Automated Attendant Message for each CO/PBX Data No. Trunk. When the Automated Attendant Message is assigned to each CO/PBX Trunk, the system automatically answers the incoming call and sends an Automated Attendant Message to the calling party.
Page 546: Automatic Release Signal Detection Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 3-40 Automatic Release Signal Detection CO/PBX Line Mode Selection Submode — General Description Use this Memory Block to specify the signal detection time for release of a CO/PBX Data No. line after a disconnect signal is received from the distant Central Office or PBX.
Page 547: Delay Announcement Assignment

Memory Block. 5 Program the next Memory Block or press to go back on-line. Related Programming Refer to individual features in the Electra Elite IPK Features and Specifications Manual. ___________________________________________________________________________________ 2 - 470 Memory Blocks...
Page 548: Dit Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 3-42 DIT Assignment CO/PBX Line Mode General Description Submode Use this Memory Block to assign a Day Mode direct trunk termination to an — independent station. Data No. R2500 is required for 5-, 6-, or 7-digit Extension Numbers.
Page 549

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Programming Procedures 5 Program the next Memory Block or press to go back on-line. Related Programming M.B. Number Memory Block Name 1-1-46 Access Code (1-Digit) Assignment 1-1-47 Access Code (2-Digit) Assignment 1-1-48 Access Code (3-Digit) Assignment...
Page 550: Ana Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 3-43 ANA Assignment CO/PBX Line Mode General Description Submode Use this Memory Block to assign a Night Mode Direct trunk termination to a station. — R2500 is required for 5-, 6-, or 7-digit Extension Numbers.
Page 551

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-1-46 Access Code (1-Digit) Assignment 1-1-47 Access Code (2-Digit) Assignment 1-1-48 Access Code (3-Digit) Assignment 1-2-03 2~7-Digit Station Number Selection 1-2-34 Expanded Station Number Assignment 3-42...
Page 552: Caller Id Display Assignment For Co/pbx Line

Memory Block. 5 Program the next Memory Block or press to go back on-line. Related Programming Refer to individual features in the Electra Elite IPK Features and Specifications Manual. ___________________________________________________________________________________ Programming Manual 2 - 475...
Page 553

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Notes To display ANI/Caller ID Indication for normal incoming CO calls and CAR incoming calls, both Caller ID Indication and Ring assignment must be Programmed. A maximum of 15 Multiline Terminals can be assigned system-wide to display ANI/Caller ID for normal incoming CO calls and CAR incoming calls using Memory Block 1-1-78 (Caller ID Display Assignment for System Mode).
Page 554: Live Record Trunk Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 3-45 Live Record Trunk Selection CO/PBX Line Mode General Description Submode Use this Memory Block to specify per Trunk whether or not to allow Live Record for — Digital Voice Mail. Data No.
Page 555: Isdn Line Spid Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 3-50 ISDN Line SPID Assignment CO/PBX Line Mode General Description Submode Use this Memory Block to assign the Integrated Services Digital Network Service — Profile Identifier (ISDN SPID) number. Data No. Display C O / P B X N o .
Page 556: Isdn Trunk Directory Number Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 3-52 ISDN Trunk Directory Number CO/PBX Line Mode Assignment Submode — General Description Use this Memory Block to assign the Integrated Services Digital Network (ISDN) Data No. Directory Number. Display PC Programming C O / P B X...
Page 557: Caller Name Indication Selection

CO/PBX Line Mode General Description Submode When an Caller ID number is detected, the Electra Elite IPK system can check the — speed dialing buffer for a match. When a name is assigned to a matched number, the name can be displayed, when allowed by this assignment.
Page 558: Automated Attendant 1st To 2nd Delay Announcement Interval Time Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 3-59 Automated Attendant Function CO/PBX Line Mode Selection Submode — General Description Use this Memory Block to specify whether the Automated Attendant is to operate in Data No. the Normal DISA Mode or in the Delay Announcement mode.
Page 559: Dit/ana Delay Answer Time Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 3-61 DIT/ANA Delay Answer Time CO/PBX Line Mode Selection Submode — General Description Use this Memory Block to specify the time an incoming call rings before being Data No. changed to a DIT/ANA call.
Page 560

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Display (3000 or higher) C O / P B X N o . D a t a S e t t i n g T i t l e D a t a ( 0 1 ~ 6 4 ) N o .
Page 561: Dit Tenant Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 3-62 DIT Tenant Assignment CO/PBX Line Mode General Description Submode Use this Memory Block to assign each Trunk to a Master Tenant for the DIT/ANA to — follow the Day/Night/Weekend mode settings. Data No.
Page 562: Dit Weekend Mode Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 3-63 DIT Weekend Mode Selection CO/PBX Line Mode General Description Submode Use this Memory Block to enable weekend (Holiday) Mode check on Tenant Groups — for incoming DIT calls. Data No. Display C O / P B X S e t t i n g N o .
Page 563: Dit Night Mode Delay Answer Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 3-64 DIT Night Mode Delay Answer CO/PBX Line Mode Selection Submode — General Description Use this Memory Block to specify whether or not the DIT Delay Answer Time applies Data No. to the CO/PBX calls ringing in Night Mode.
Page 564: Hold Tone Automated Attendant Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 3-65 Hold Tone Automated Attendant CO/PBX Line Mode Selection Submode — General Description Use this Memory Block to specify the Automated Attendant message that is played to Data No. an extension or DID trunk on an incoming call.
Page 565

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-4-11 Automated Attendant Message Day/Night Mode Selection 1-4-17 Automated Attendant Delay Announcement Hold Tone Selection ___________________________________________________________________________________ 2 - 488 Memory Blocks...
Page 566: Co/pbx Ringing Pattern Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 3-67 CO/PBX Ringing Pattern Selection CO/PBX Line Mode General Description Submode Use this Memory Block to specify the ringing pattern assigned to each CO/PBX line. — Display Data No. C O / P B X N o .
Page 567

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ The Ring Patterns are shown in the table below: s= seconds Pattern No Ring ___________________________________________________________________________________ 2 - 490 Memory Blocks...
Page 568: Cut Through Trunk Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 3-69 911 – Cut Through Trunk Selection CO/PBX Line Mode General Description Submode Use this Memory Block to specify which trunk or trunks are released when a 911 call is — placed. Data No.
Page 569

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 3-03 Trunk-to-Trunk Group Assignment 3-33 Disconnect Recognition Time Selection 3-91 Trunk Type Selection 1-1-24 PBX/CTX Access Code Assignment I 1-1-25 PBX/CTX Access Code Assignment II Notes When only one trunk is assigned YES, this is the only trunk used for 911-Cut Through.
Page 570: Cic Number Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 3-70 CIC Number Assignment CO/PBX Line Mode General Description Submode Use this Memory Block to assign the Circuit Identification Code for each voice channel — used for K-CCIS. Data No. Display C O N o .
Page 571

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-1-05 Start Time Selection 1-15-00 K-CCIS Main/Remote Office selection 1-15-01 Common Signal Channel Data Speed Assignment 1-15-02 Common Signal Channel Assignment 1-15-03 Originating Point Code Assignment...
Page 572: Co Message Waiting Yes/no Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 3-73 CO Message Waiting Yes/No Selection CO/PBX Line Mode General Description Submode Use this Memory Block to specify whether or not the CO Message Waiting feature is — allowed per CO/PBX Line. Data No.
Page 573: Isdn-bri/pri Directory Number Checking Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 3-77 ISDN-BRI/PRI Directory Number CO/PBX Line Mode Checking Selection Submode — General Description Use this Memory Block to determine whether or not the BRT/PRT ETU passes the Data No. Directory Number to the CPU when it is received in the ISDN Set Up message.
Page 574

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 3-50 ISDN Line SPID Assignment 3-52 ISDN Trunk Directory Number Assignment 3-91 Trunk Type Selection 1-1-20 DID Digit Length Selection 1-1-21 DID Digit Conversion Assignment 1-1-22...
Page 575: Polarity Reverse Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 3-90 Polarity Reverse Selection CO/PBX Line Mode General Description Submode Use this Memory Block to enable a Central Office to Reverse the Polarity to provide an — answer supervision signal. In North America and Canada, this type of answer supervision is not normally supported by the CO.
Page 576: Trunk Type Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 3-91 Trunk Type Selection CO/PBX Line Mode General Description Submode Use this Memory Block to specify an external line as a CO, PBX/CTX, Tie, DID, or — CTX Assume - 9 line. Data No.
Page 577: Trunk (installed, Dp/dtmf) Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 3-92 Trunk (Installed, DP/DTMF) CO/PBX Line Mode Selection Submode — General Description Use this Memory Block to specify an external line as DP (10 pps or 20 pps), DTMF Data No. line, or not connected (NIL).
Page 578: Co/pbx Ring Assignment (day Mode)

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 4-01 CO/PBX Ring Assignment Telephone Mode (Day Mode) Submode — General Description Use this Memory Block to assign incoming CO/PBX calls to ring on Multiline Terminals Data No. in Day Mode. Display PC Programming...
Page 579

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Page 7 – Trunks 49~56 LK 1 LK 2 LK 3 LK 4 LK 5 LK 6 LK 7 LK 8 Page 8 – Trunks 57~64 LK 1 LK 2 LK 3 LK 4...
Page 580: Co/pbx Ring Assignment (night Mode)

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 4-02 CO/PBX Ring Assignment Telephone Mode (Night Mode) Submode — General Description Use this Memory Block to assign incoming CO/PBX calls to ring in Night Mode. Data No. Display PC Programming T e l...
Page 581

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Page 6 – Trunks 41~48 LK 1 LK 2 LK 3 LK 4 LK 5 LK 6 LK 7 LK 8 Page 7 – Trunks 49~56) LK 1 LK 2 LK 3 LK 4...
Page 582: Doorphone Chime Assignment (day Mode)

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 4-03 Doorphone Chime Assignment Telephone Mode (Day Mode) Submode — General Description Use this Memory Block to assign up to four doorphones to chime at each station in day Data No. mode. Display...
Page 583

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-7-00 Doorphone Assignment 1-7-01 Doorphone Display Time Selection 1-7-04 Doorphone Ringing Pattern Selection 1-7-05 Doorphone Ringing Frequency Selection Notes Telephone ports A0~C0 are ports 100~120. ___________________________________________________________________________________...
Page 584: Doorphone Chime Assignment (night Mode)

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 4-04 Doorphone Chime Assignment Telephone Mode (Night Mode) Submode — General Description Use this Memory Block to assign up to four doorphones to chime at each station in Data No. Night Mode. Display...
Page 585

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-7-00 Doorphone 1-7-01 Doorphone Display Time Selection 1-7-04 Doorphone Ringing Pattern Selection 1-7-05 Doorphone Ring Frequency Selection Notes Telephone ports A0~C0 are ports 100~120. ___________________________________________________________________________________ 2 - 508...
Page 586: Code Restriction Class Assignment (day Mode)

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 4-07 Code Restriction Class Assignment Telephone Mode (Day Mode) Submode — General Description Use this Memory Block to specify Code Restriction Class per station in Day Mode. Data No. Display PC Programming T e l...
Page 587: Code Restriction Class Assignment (night Mode)

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 4-08 Code Restriction Class Assignment Telephone Mode (Night Mode) Submode — General Description Use this Memory Block to specify Code Restriction Class per station in Night Mode. Data No. Display PC Programming T e l...
Page 588: Telephone To Tenant Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 4-09 Telephone to Tenant Assignment Telephone Mode General Description Submode Use this Memory Block to specify Tenant Assignment per station. — Display Data No. T e l P o r t S e t t i n g N o .
Page 589

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Notes Stations can be assigned to one of 48 Tenant Number (00 ~ 47). The Call Pickup group is determined by Tenant assignment. Telephone ports A0~C0 are ports 100~120. ___________________________________________________________________________________ 2 - 512...
Page 590: Station Number Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 4-10 Station Number Assignment Telephone Mode General Description Submode Use this Memory Block to assign a station number to each telephone. — R2500 is required for 5-, 6-, or 7-digit Extension Numbers. Data No.
Page 591

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-1-46 Access Code (1-Digit) Assignment 1-1-47 Access Code (2-Digit) Assignment 1-1-48 Access Code (3-Digit) Assignment 1-2-03 2~7-Digit Station Number Selection 1-2-24 Expanded Station Number Assignment Notes Station Number Assignment is per station.
Page 592: Ringing Line Preference Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 4-11 Ringing Line Preference Selection Telephone Mode General Description Submode Use this Memory Block to specify whether or not each station user can answer — incoming ringing CO/PBX calls by going off-hook. Data No.
Page 593

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Notes Programming for this Memory Block applies to Ring Assigned telephones only. An intercom call cannot be originated after a ring assigned CO/PBX line terminates on the telephone. Telephone ports A0~C0 are ports 100~120.
Page 594: Line Key Selection For Telephone Mode

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 4-12 Line Key Selection for Telephone Telephone Mode Mode Submode — General Description Use this Memory Block to assign a function to each CO/PBX line key on each Data No. telephone in a tenant specified as Telephone Mode in Memory Block 2-05 (Line Key Selection).
Page 595

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Programming Procedures (Continued) 3 Press the CO/PBX line key to select a function for Line Key No. 1, and use dial Default Values keys to enter Setting Data 2 if required. For Tel 01~CO: LK01~08 Assigned to CO/PBX lines 01~08.
Page 596

Line Key Selection (Tenant Mode) Notes When an Electra Elite IPK system is installed as a Key Function (KF) system, all COs must be assigned to the line keys. Trunk groups, Route Advance Blocks and Least Cost Routing (LCR) cannot be assigned.
Page 597: Co/pbx Busy Forward Station Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 4-13 CO/PBX Busy Forward Station Telephone Mode Assignment Submode — General Description Use this Memory Block to specify up to two telephones to ring when a CO/PBX call Data No. terminates at a busy station.
Page 598: Intercom Master Hunt Number Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 4-14 Intercom Master Hunt Number Telephone Mode Selection Submode — General Description Use this Memory Block to specify whether or not each telephone port number is Data No. designated as an intercom master hunt number.
Page 599

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Notes When YS is assigned, an incoming internal call from another station, Automated Attendant transferred call, or DIT/ANA/DID/Tie line designated call is forwarded to a station specified in Memory Block 4-15 (Intercom Master Hunt Number Forward Assignment) when the line is busy.
Page 600: Intercom Master Hunt Number Forward Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 4-15 Intercom Master Hunt Number Telephone Mode Forward Assignment Submode — General Description Use this Memory Block to specify a telephone to ring for an incoming call when YS is Data No. specified in Memory Block 4-14 (Intercom Master Hunt Number Selection) and the Intercom Master Hunt Number line is busy.
Page 601

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Programming Procedures 3 Use dial pad to enter station number. To set Tel. Port No. to forward station number 300, Default Values C K K enter All Telephones Not Specified Use the following to enter data:...
Page 602

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Notes Telephone ports A0~C0 are ports 100~120. Example - Assign the following Memory Blocks: Memory Block 4-14 (Intercom Master Hunt Number Selection) Telephone Port Number 01 ==> YES All other Port Numbers ==> NO...
Page 603: Station To Class Of Service Feature Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 4-17 Station to Class of Service Feature Telephone Mode Assignment Submode — General Description Use this Memory Block to specify a class for each Table (1 or 2) to enable/disable Data No. features per station.
Page 604

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Notes Table 1 includes features that telephone ports 01 and 02 users are normally allowed to activate. Select any Class pattern specified in Memory Block 1-8-07 [Class of Service (Attendant) Feature Selection 1].
Page 605: Station Name Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 4-18 Station Name Assignment Telephone Mode General Description Submode Use this Memory Block to assign names for telephone stations. — R4000 or higher is required to support 16 characters for the Station Name.
Page 606

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Notes While an internal line is ringing or in use, the station number and name of the other party are displayed. The name is not displayed when Tone Override, Automatic Callback, or Callback Request is displayed.
Page 607: Trunk Outgoing Restriction

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 4-19 Trunk Outgoing Restriction Telephone Mode General Description Submode Use this Memory Block to specify per CO/PBX line whether or not to restrict line — seizure for an outgoing call. Data No. Display...
Page 608

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Programming Procedures (Continued) 3 Press the CO/PBX line key corresponding to each CO/PBX line. Default Values Not Restricted The LED indication changes to indicate data each time a CO/PBX line key is pressed.
Page 609: Prime Line/hot Line Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 4-23 Prime Line/Hot Line Assignment Telephone Mode General Description Submode Use this Memory Block to enable user to access various features when going — off-hook. Data No. Display T e l P o r t PC Programming N o .
Page 610

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Notes Prime Line function enables a user to seize a specified trunk when the Multiline Terminal goes off-hook. Refer to function codes 063 and 064 for Memory Blocks 1-1-46 [Access Code (1-Digit) Assignment] and 1-1-47 [Access Code (2-Digit) Assignment].
Page 611: Slt Hookflash Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 4-24 SLT Hookflash Assignment Telephone Mode General Description Submode Use this Memory Block to either Hold or disconnect the trunk for the Single Line — Telephone (SLT) hooking operation. Data No. Display T e l...
Page 612

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Notes This Memory Block affects only Single Line Telephone stations assigned Prime Line in Memory Block 4-23 (Prime Line/Hot Line Assignment). When Prime Line is assigned to an Single Line Telephone, hookflash drops the CO and issues intercom (ICM) dial tone when this Memory Block is set to disconnect.
Page 613: Disa Id Number Station Assignment

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 4-26 DISA ID Number Station Assignment Telephone Mode General Description Submode Use this Memory Block to assign the Direct Inward System Access (DISA) ID Buffer — Number corresponding to the station port number. The Station Message Detail Data No.
Page 614: Multilingual Lcd Indication Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 4-28 Multilingual LCD Indication Telephone Mode Selection Submode — General Description Data No. Use this Memory Block to specify the language displayed on the Multiline Terminal LCD. PC Programming DisplayS +BTM T e l...
Page 615: Hfu Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 4-29 HFU Selection Telephone Mode General Description Submode Use this Memory Block to enable/disable per station the built-in Handsfree HFU-U — Unit. Data No. Display T e l PC Programming P o r t...
Page 616: Hold/transfer Recall Display Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 4-30 Hold/Transfer Recall Display Telephone Mode Selection Submode — General Description Use this Memory Block to enable/disable the Hold Recall indication on the LCD. Data No. Display PC Programming T e l P o r t +BTM N o .
Page 617: Receiving Internal/all Call Page Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 4-31 Receiving Internal/All Call Page Telephone Mode Selection Submode — General Description Use this Memory Block to specify per station whether or not an Internal Zone or Data No. Internal All Zone Page is received.
Page 618: Trunk Digit Restriction

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 4-32 Trunk Digit Restriction Telephone Mode General Description Submode Use this Memory Block to specify per port the maximum number of digits that can be — dialed on any outside line. Data No.
Page 619: Voice Mail/slt Selection

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ 4-35 Voice Mail/SLT Selection Telephone Mode General Description Submode Use this Memory Block to specify whether or not a Voice Mail system is interfaced with — the system for Single Line Telephone ports.
Page 620

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ Notes The SLT(1)-U( ) ADP Adapter and the ADA(2)-W Unit do not support Voice Mail. Only 16 Voice Mail ports are supported by this system. Telephone ports A0~C0 are ports 100~120. ___________________________________________________________________________________ Programming Manual...
Page 621: Voice Prompt Selection

Memory Block. 5 Program the next Memory Block or press to go back on-line. Related Programming Refer to individual features in the Electra Elite IPK Features and Specifications Manual. Notes Telephone ports A0~C0 are ports 100~120. ___________________________________________________________________________________...
Page 622: Extension Line Key Ring Assignment (day Mode)

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 4-37 Extension Line Key Ring Assignment Telephone Mode (Day Mode) Submode — General Description Use this Memory Block to specify the day ringing assignment on incoming calls to a Data No. Secondary Incoming Extension (SIE) or a Call Arrival key.
Page 623

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Programming Procedures 3 Press the Line Key corresponding to ringing required for Tel Port No. Default Values All Telephones: No Ring The LED indication changes to indicate data each time a CO/PBX Line Key is pressed.
Page 624: Extension Line Key Ring Assignment (night Mode)

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 4-38 Extension Line Key Ring Assignment Telephone Mode (Night Mode) Submode — General Description Use this Memory Block to specify the night ringing assignment on incoming calls to a Data No. Secondary Incoming Extension (SIE) or a Call Arrival Key.
Page 625

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Programming Procedures 3 Press the Line Key corresponding to ringing required for Tel Port No. Default Values All Telephones: No Ring The LED indication changes to indicate data each time a CO/PBX Line Key is pressed.
Page 626: Apr Ring Mode Assignment

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 4-39 APR Ring Mode Assignment Telephone Mode General Description Submode Use this Memory Block to specify the ringing mode for a Single Line Telephone — connected to an AP(R)-R or APR-U Unit. Data No.
Page 627

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Notes No Ring means that no calls ring at the Single Line Device connected to an AP(R)-R or APR-U Unit. Station Number ring means that only calls directed to the Multiline Terminal Station Number, ring at the Single Line Device connected to an AP(R)-R or APR-U Unit.
Page 628: Lcr Class Selection

Use this Memory Block to specify per station the Least Cost Routing (LCR) Class. The — Electra Elite IPK system has four Area Code Tables. Each LCR Class can have different Trunk group access to allow priority levels for the station user. This Memory Data No.
Page 629

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Notes LCR Class Selection corresponds to Area Code Tables as follows: Class 0 No LCR Class 1 Use Area Code Table 1 Class 2 Use Area Code Table 2 Class 3 Use Area Code Table 3...
Page 630: Sie/car Ringing Line Preference Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 4-41 SIE/CAR Ringing Line Preference Telephone Mode Selection Submode — General Description Use this Memory Block to specify whether or not to allow Ringing Line Preference (go Data No. off-hook or press Speaker key) on all telephones that are assigned Secondary Incoming Extension (SIE) and/or Call Arrival keys.
Page 631

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 4-37 Extension Line Key Ring Assignment (Day Mode) 4-38 Extension Line Key Ring Assignment (Night Mode) Notes Telephone ports A0~C0 are ports 100~120. The SIE/CAR must be ringing for this Memory Block to work.
Page 632: Call Forward-busy Immediately/delay Selection

Electra Elite IPK Document Revision 4 ___________________________________________________________________________________ 4-42 Call Forward-Busy Immediately/ Telephone Mode Delay Selection Submode — General Description Use this Memory Block to specify immediate forward (NO) or delay forward (YS) for an Data No. Incoming CO/PBX call if the station is set for Call Forward – Busy.
Page 633

Document Revision 4 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-2-22 Call Forward No Answer Time Selection Notes Telephone ports A0~C0 are ports 100~120. ___________________________________________________________________________________ 2 - 556 Memory Blocks...