Page 1
NOTICE Note that when converting this document from its original format to a .pdf file, some minor font and format changes may occur causing slight variations. When viewing and printing this document, we cannot guarantee that your specific PC or printer will support all of the fonts or graphics.
Page 2
SIP TRUNK HARDWARE, INSTALLATION AND MAINTENANCE MANUAL N E C U n i f i e d S o l u t i o n , I n c . D o c u m e n t R e v i s i o n 2 I N T - 2 0 2 2 ( I P K ) C D S t o c k N u m b e r 7 5 0 4 5 4...
Page 4
Contents of this manual are subject to change without prior notice at the discretion of NEC Unified Solutions, Inc. This document has been prepared for the use of employees and customers of NEC Unified Solutions, Inc. and may not be reproduced without prior written approval of NEC Unified Solutions, Inc.
Page 7
Section 3 Returning the IAD(8)-U( ) ETU (SIP Trunk) to Default Configuration ..................B-2 Appendix C Glossary Appendix D Electra Elite IPK IAD(8)-U( ) ETU Installation Section 1 Introduction ..................D-1 Section 2 Installing IAD (8)-U( ) ETU Package ..........D-1 2.1 Description ..................
Page 8
Document Revision 2 SIP Trunk ___________________________________________________________________________________ THIS PAGE INTENTIONALLY LEFT BLANK ___________________________________________________________________________________ Table of Contents...
Page 9
LIST OF FIGURES ___________________________________________________________________________________ Table 1-1 Default Boot Sequence: In Active IAD(8)-U10 ETU - Without IP Application Loaded ......................1-2 Table 1-2 Active IAD(8)-U10 ETU - With IP Application Loaded ........... 1-3 Table 1-3 IAD(8)-U( ) Switch Settings ..................1-4 Table 3-1 IAD Trunk Card Assignment ..................
Page 10
Document Revision 2 SIP Trunk ___________________________________________________________________________________ THIS PAGE INTENTIONALLY LEFT BLANK ___________________________________________________________________________________ List of Figures and Tables...
ECTION ESCRIPTION The IAD(8)-U( ) ETU is an optional interface package for Electra Elite IPK KTS that can combine trunk and tie line calls into SIP trunks. This ETU can be assigned as a 2-port TLI(2)-U10, 4-port DID (4)-U10, 4-port or 8-port DTI-U10 ETU, COI/ COID(4)-U10, 8-port COI/COID(8)-U10 or DTI(4)/DTI(8) ETU.
Document Revision 2 SIP Trunk ___________________________________________________________________________________ Refer to the Appendix D Electra Elite IPK IAD(8)-U( ) ETU Installation for instructions for installing the IAD ETU. ECTION NDICATORS WITCHES ONNECTORS LED Indicators The total of nine LEDs on this ETU are described in...
2.1.2 Hot Swap The IAD(8)-U( ) does not require powering down the ETU or KSU. The user can remove the IAD8)-U( ) ETU from the Electra Elite IPK KSU the same way any other ETU is removed. 2.1.3 Ethernet Status There are two built-in LEDs on the front of each RJ-45 connector to indicate Ethernet connection status.
Reserved for future use RJ-45 Ethernet connector for future use Default RJ-45 Ethernet connector Installation The IAD (8)-U( ) ETU can be installed in any KSU slot that supports the applicable simulated ETU. ___________________________________________________________________________________ 1 - 4 Electra Elite IPK IAD(8)-U( ) ETU...
Page 15
SIP Trunk Document Revision 2 ___________________________________________________________________________________ Pushbutton Switch S1 is the reset switch. Environmental Conditions The following environmental conditions apply for IAD (8)-U( ) ETU operation: Operating Temperature: +32 to 104°F (0 to 40C) Operating Humidity: 10% to 90 % (non-condensing) ___________________________________________________________________________________ Hardware, Installation and Maintenance Manual 1 - 5...
Page 17
(Refer to Table 1-3 IAD(8)-U( ) Switch Settings on page 1-4.) Place the IAD(8)-U( ) ETU in the Electra Elite IPK KSU. Connect the Ethernet cable to J6 connector. The CH1~CH8 LEDs start to run indicating that the system is initializing the IP networking parameters.
Page 19
YSTEM ROGRAMMING The IAD (8)-U10 ETU is recognized by the Electra Elite IPK system as a COI(4)/ (8)-U10 ETU, a COID(4)/(8)-U10 ETU, a DID(4)-U10 ETU, or a TLI(2)-U10 ETU, DTI ETU based on the configuration on the ETU. This ETU takes longer to initialize than the other Electra Elite IPK ETUs and must be programmed using Memory Block 7-1 (Card Interface Slot Assignment).
Page 20
Follow the normal Electra Elite IPK programming procedures for assigning Line Key Selections for Telephone Mode, and other necessary features. PC Programming can also be used to program the Electra Elite IPK system. ___________________________________________________________________________________ 3 - 2...