Page 1
Notice Note that when converting this document from its original format to a .pdf file, some minor font and format changes may occur causing slight variations from the original printed document. When viewing and printing this document, we cannot guarantee that your specific PC or printer will support all of the fonts or graphics. Therefore, when you view the document, fonts may be substituted and your individual printer may not have the capability to print the document correctly.
Page 2
R O G R A M M I N G A N U A L Stock Number 750825 Document Revision 1 (Release 1000)
Page 4
NEC America, Inc. reserves the right to change the specifications, functions, or features at any time without notice. NEC America, Inc. has prepared this document for use by its employees and customers. The information contained herein is the property of NEC America, Inc. and shall not be reproduced without prior written approval of NEC America, Inc.
Page 6
PREFACE ___________________________________________________________________________________ ECTION BOUT THIS MANUAL The Programming Manual provides the technician with all of the necessary information for programming the Elite IPK system. Programming can be accomplished using a PC or a Multiline Terminal. ECTION ANUAL RGANIZATION This manual provides instructions for programming the Elite IPK system. Chapter 1 –...
Page 7
The System Hardware Manual is intended for the system installer and provides detailed instructions for installing the Elite IPK KSU, ETUs, Multiline Terminals, and optional equipment. Electra Elite IPK Least Cost Routing Manual This manual provides instructions to the service technician for programming the customer site for least cost routing.
Page 8
___________________________________________________________________________________ Electra Elite IPK ACD Plus Installation Manual This manual provides general information about the Electra Elite IPK ACD Plus features, installation procedures and feature programming. The NEC Electra Elite IPK ACD Plus is an Automatic Call Distribution card that supports up to 40 Agents and 12 supervisors at one time.
Page 9
Document Revison 1 Elite IPK ___________________________________________________________________________________ THIS PAGE INTENTIONALLY LEFT BLANK ___________________________________________________________________________________ Preface...
TABLE OF CONTENTS ___________________________________________________________________________________ Chapter 1 Multiline Terminal Programming Section 1 General Information ................1-1 Section 2 Programming the System ..............1-1 Features of Programming ..............1-2 System Programming Modes ..........1-3 Before Programming ............1-4 2.3.1 Check Points ............... 1-4 2.3.2 Preliminary Points ..............
Page 11
Document Revision 1 Elite IPK ___________________________________________________________________________________ 1-1-05 Start Time Selection ..................2-8 1-1-06 CO/PBX Incoming Ringing Alarm Time Selection ........2-9 1-1-07 Tie Line Delay Ringing Time Selection .............2-11 1-1-09 Manual Pause Selection ................2-13 1-1-11 System Transfer/Camp-On Selection ............2-15 1-1-12 Station Transfer/Camp-On Recall Time Selection ........2-16 1-1-13 CO Transfer Ring Pattern Selection ............2-17 1-1-14...
Page 12
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-54 Automated Attendant Transfer Ring Pattern ..........2-63 1-1-55 DID Line Ringing Pattern Selection ............2-65 1-1-57 CO/PBX Prepause Time Selection ............2-66 1-1-59 Synchronous Ringing Selection ..............2-67 1-1-60 8-Digit Matching Table Assignment ............2-68 1-1-61 8-Digit Matching Table to Class Assignment ..........2-70 1-1-62 System Speed Dial Override by Class Selection ........2-72 1-1-63...
Page 13
Document Revision 1 Elite IPK ___________________________________________________________________________________ 1-2-08 Specified Station Access Code Assignment ...........2-101 1-2-09~18 Customized Message 1~10 Assignment ..........2-103 1-2-19 Intercom Ring Pattern Selection .............2-104 1-2-20 Intercom Ring Tone Selection ..............2-106 1-2-21 PS Telephone Block Assignment ............2-107 1-2-22 Call Forward - No Answer Time Selection ..........2-109 1-2-23 System Call Park Recall Time Selection ..........2-110 1-2-24...
Page 15
Document Revision 1 Elite IPK ___________________________________________________________________________________ 1-8-02 PBR Receive Level Assignment for Automated Attendant/DISA ....2-182 1-8-04 Time Display (12h/24h) Selection ............2-184 1-8-07 Class of Service (Attendant) Feature Selection 1 ........2-185 1-8-08 Class of Service (Station) Feature Selection 2 ........2-188 1-8-09 Music on Hold Pattern Selection .............2-193 1-8-10 PBR Interdigit Release Time Selection ...........2-194...
Page 16
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-9-00 DISA ID Code Assignment ..............2-231 1-9-02 DISA Password Effect/Invalid Selection ..........2-232 1-10-00 Call by Call Type of Network ID Assignment ...........2-233 1-10-01 Call by Call ID Plan Assignment ..............2-235 1-10-02 Call by Call Type of Number Assignment ..........2-237 1-10-03 Call by Call Numbering Plan ID Assignment ...........2-239 1-10-04...
Page 17
Document Revision 1 Elite IPK ___________________________________________________________________________________ 1-14-01 ARS Dialing Assignment .................2-286 1-14-02 ARS Dial Allow/Deny Selection ...............2-288 1-14-03 ARS Route Table Number Assignment ...........2-290 1-14-04 ARS Trunk Group to Route Number Assignment ........2-292 1-14-05 ARS Digit Delete Assignment ..............2-294 1-14-06 ARS Digit Add Assignment ..............2-296 1-14-07 ARS Max Digit Assignment ..............2-298...
Page 18
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-16-10 Port Mirroring Selection ................3-353 1-16-11 Mirroring Source Port Assignment ............3-355 1-16-12 Mirroring Target Port Assignment ............3-357 1-16-13 VLAN Group to VLAN ID Assignment .............3-359 1-16-14 VLAN Group and Port Selection .............3-361 1-16-15 VLAN Tag Insertion Selection ..............3-363 1-16-16 Flow Control for Full Duplex Selection ............3-365 1-16-17...
Page 19
Document Revision 1 Elite IPK ___________________________________________________________________________________ 3-24 Tie Line Incoming Interdigit Timeout Selection ........2-406 3-25 Tie Line Wink/Delay Signal Detect Timeout Selection ......2-408 3-27 Tie Line Dial Tone Selection ..............2-410 3-28 Tie Line Reorder Tone Selection ............2-411 3-29 Trunk Internal Transmit Pad Selection ............2-413 3-30 Trunk Internal Receive Pad Selection .............2-415 3-31...
Page 26
Elite IPK Document Revision 1 ___________________________________________________________________________________ 3.3.37 Call by Call Facility Coding Value Assignment (Service) (Memory Block 1-10-05) ........3-37 3.3.38 Call by Call Facility Coding Value Assignment (Feature) (Memory Block 1-10-06) ........3-37 3.3.39 Call by Call Service Parameter Assignment (Memory Block1-10-07) .............
Page 27
Document Revision 1 Elite IPK ___________________________________________________________________________________ Service Conditions ............. 3-47 Call by Call (CBC) Termination Flowchart ......3-50 Appendix A Function Time Chart Section 1 Time Chart .................... A-1 Appendix B Character Codes Section 1 Character Assignment ................ B-1 Character Code Tables ..............B-1 Dial Pad Character Assignment ...........
Page 28
LIST OF FIGURES ___________________________________________________________________________________ Figure 1-1 Programming Flowchart ..................1-2 Figure 1-2 Elite IPK Multiline Terminal ................1-6 Figure 1-3 Page Display for 8-Key, 16-Key and 24-Key Multiline Terminals ....1-10 Figure 1-4 Page Switching for Data Values ..............1-11 Figure 3-1 Automatic Route Selection (ARS) System Data Flow ........3-19 ___________________________________________________________________________________ Programming Manual...
Page 29
Document Revison 1 Elite IPK ___________________________________________________________________________________ THIS PAGE INTENTIONALLY LEFT BLANK ___________________________________________________________________________________ List of Figures...
LIST OF TABLES ___________________________________________________________________________________ Table 1-1 Programming Modes ....................1-3 Table 1-2 Multiline Terminal Keys Used for Programming ............1-7 Table 3-1 Automatic Route Selection to Route Number Assignment ........3-20 Table 3-2 Route Number to Trunk Group/RAB Selection and Digit Control ......3-24 Table 3-3 Memory Block Data ....................
Page 31
Document Revison 1 Elite IPK ___________________________________________________________________________________ THIS PAGE INTENTIONALLY LEFT BLANK ___________________________________________________________________________________ xxii List of Tables...
Multiline Terminal Programming C h a p t e r 1 ___________________________________________________________________________________ ECTION ENERAL NFORMATION A stored program controls the Elite IPK system. When the system is initially powered up, the CPUI( )-U( ) ETU scans all interface and ISA slots to determine the hardware configuration.
Document Revison 1 Elite IPK ___________________________________________________________________________________ New Installation Existing System Develop System Component Function Data Sheet Replacement Change Installation Rewrite System Rewrite System Data Sheet Data Sheet Test System with Default Installation Values System Data System Data System Data Programming (Note 1) Programming (Note 2) Programming (Note 3) TEST...
Elite IPK Document Revision 1 ___________________________________________________________________________________ Two Multiline Terminals, connected to ports 01 and 02, respectively, can be used simultaneously for programming. System Programming Modes Modes and submodes are listed in Table 1-1 Programming Modes. Table 1-1 Programming Modes Line Line Mode Name Submode Name...
Document Revison 1 Elite IPK ___________________________________________________________________________________ Table 1-1 Programming Modes (Continued) Line Line Mode Name Submode Name LK 1 ROM Version Confirmation LK 2 System Speed Dial Memory Clear LK 8 Special Mode LK 3 Station Speed Dial Memory Clear LK 8 Second Initialization Before Programming...
Elite IPK Document Revision 1 ___________________________________________________________________________________ Writing System Data After turning on power, the system data can be programmed using a Multiline Terminal connected to port 01 or port 02 (the Multiline Terminal must be idle). System programming can be performed while other Multiline Terminals in the system are in use.
Document Revison 1 Elite IPK ___________________________________________________________________________________ Programming Methods 2.5.1 Initializing the System Turn on the new Key Service Unit (KSU) power supply. After approximately 30 seconds, the system operates with the system default values. 2.5.2 Using the Multiline Terminal for Programming System programming can be performed using a Display Multiline Terminal that is connected to station port 01 or 02.
Elite IPK Document Revision 1 ___________________________________________________________________________________ Table 1-2 Multiline Terminal Keys Used for Programming provides a list and description of the keys used during Multiline Terminal Programming. Table 1-2 Multiline Terminal Keys Used for Programming Description Used to enter data from the dial pad or to specify a Memory Block location.
Document Revison 1 Elite IPK ___________________________________________________________________________________ Table 1-2 Multiline Terminal Keys Used for Programming Description This key is used to enter a pause, hyphen, asterisk or pound. To enter an asterisk or pound: The Message Waiting LED turns on and off after i s pressed.
Elite IPK Document Revision 1 ___________________________________________________________________________________ Dial , and i n sequence. The Multiline Terminal LCD indicates program mode is now active. P R O G R A M M O D E T I M E D I S P L A Y While off-line, the programming terminal cannot be signaled by any system station.
Elite IPK Document Revision 1 ___________________________________________________________________________________ Figure 1-4 Page Switching for Data Values is an example of 10 data values. Values are displayed on two pages. 16-Key Multiline Terminal (Page 1) LK 1 LK 2 LK 3 LK 4 Data 01 Data 02 Data 03 Data 04...
Document Revison 1 Elite IPK ___________________________________________________________________________________ ECTION YSTEM The System Data List is a complete list of Memory Blocks that are available in the Elite IPK system. The information is organized by mode, submode, and then numerically by Memory Block number. The Memory Block number and name, the default values, and programming values are provided for each Memory Block.
Page 44
Elite IPK Document Revision 1 ___________________________________________________________________________________ LK 1 System Mode LK 1 CO Line (Continued) Data Memory Block Name Default Value Programming Values DID Digit Conversion Assignment NO, YS DID Digit Conversion Table T (Station or Closed Number) TN (Tenant) DID Forward Station Number for NON, T (TEL), TN (Tenant) Busy Station or Undefined Digit...
Page 45
Document Revison 1 Elite IPK ___________________________________________________________________________________ LK 1 System Mode LK 1 CO Line (Continued) Data Memory Block Name Default Value Programming Values CO Line Ringing Pattern Selection A ~ H, NO PBX Line Ringing Pattern Selection A ~ H, NO Tie Line Delay Ring Pattern A ~ H, NO Selection...
Page 46
Elite IPK Document Revision 1 ___________________________________________________________________________________ LK 1 System Mode LK 1 CO Line (Continued) Data Memory Block Name Default Value Programming Values Tie Line Code Restriction NO = No Restriction YS = Restriction Assignment Code Restriction Class Assignment Class 00 ~ 15 when Lockout is Set First Delay Announcement Start In seconds: 00, 10, 20, 30, 40, 50, 60...
Page 47
Document Revison 1 Elite IPK ___________________________________________________________________________________ LK 1 System Mode LK 2 ICM Data Memory Block Name Default Value Programming Values ∞ Internal Paging Timeout Selection (No Limit) 90s, 120s, Intercom Call Voice/Tone Signal VOICE TONE VOICE Selection Automatic Callback Release Time 30s, 1m, 2m, 3m, 5m, 10m, 20m, 30m Selection 2-, 3-, or 4-Digit Station Number...
Page 48
Elite IPK Document Revision 1 ___________________________________________________________________________________ LK 1 System Mode LK 2 ICM (Continued) Data Memory Block Name Default Value Programming Values PS Out of Area Time Assignment 00~99 sec. IP Phone Block Assignment Off (No IP Phone ON (Green), IP Assigned Blocks Assigned) On (Red), Block Not available LK 1 System Mode...
Page 49
Document Revison 1 Elite IPK ___________________________________________________________________________________ LK 1 System Mode LK 4 Transfer/Automated Attendant (A.A.) Data Memory Block Name Default Value Programming Values Tandem Transfer Automatic In minutes: 000~999 Disconnect Time Selection Automated Attendant First Digit 5s, 10s, 20s, 30s, 40s, 50s, 60s PBR Release Time Selection ∞...
Page 50
Elite IPK Document Revision 1 ___________________________________________________________________________________ LK 1 System Mode LK 4 Transfer/Automated Attendant (A.A.) (Continued) Data Memory Block Name Default Value Programming Values 0s, 10s, 20s, 30s, 1m, 2m, 3m, 4m, 5m, Automated Attendant 1 to 2 10m, 20m. Delay Announcement Interval Time Selection Automated Attendant Delay...
Page 51
Document Revison 1 Elite IPK ___________________________________________________________________________________ LK 1 System Mode LK 6 DSS Data Memory Block Name Default Value Programming Values Attendant Add-On Console to Refer to 1-6-01 Attendant Add-On Console to Telephone Port Assignment on page 2-159. Telephone Port Assignment DSS Call Voice/Tone Signal VOICE TONE, VOICE...
Page 52
Elite IPK Document Revision 1 ___________________________________________________________________________________ LK 1 System Mode LK 7 ESP (Continued) Data Memory Block Name Default Value Programming Values External Speaker Chime Selection PRT (Normal paging tone before Page) C-S (Chime Start Only) C-B (Chime Start/End) External Speaker Chime Start Time In milliseconds: 000, 100, 200, 300, 400, 500, 600, 700, 800, 900, 1000, 1100, 1200, Selection...
Page 53
Document Revison 1 Elite IPK ___________________________________________________________________________________ LK 1 System Mode LK 8 PBR/Miscellaneous (Continued) Data Memory Block Name Default Value Programming Values Voice Prompt to Tone Assignment Refer to 1-8-16 Voice Prompt to Tone Assignment on page 2-203 PC Programming Password Class 1, 2 All Blank Assignment Site Name Assignment...
Page 54
Elite IPK Document Revision 1 ___________________________________________________________________________________ LK 1 System Mode LK 8 PBR/Miscellaneous (Continued) Data Memory Block Name Default Value Programming Values Enhanced 911 Alternate Route No Alternate Route 101~132 for trunk group 01~32 Assignment (Maintenance Busy) 201~216 for route advance block 01~16 Enhanced 911 Dialing Digit 1, 11, 911 Assignment...
Page 55
Document Revison 1 Elite IPK ___________________________________________________________________________________ LK 1 System Mode LK 10 Call by Call (Continued) Data Memory Block Name Default Value Programming Values Call by Call Type of Number All RABs 0 Unknown International Assignment National Network Specific Subscriber or Local Not Used Call by Call Numbering Plan ID All RABs 00...
Page 56
Elite IPK Document Revision 1 ___________________________________________________________________________________ LK 1 System Mode LK 10 Call by Call (Continued) Data Memory Block Name Default Value Programming Values Call by Call Outgoing/Incoming 01~16 For Electra Elite 48 (Default 16), 01~64 For Electra Elite 192(Default 64) SFG Assignment 99 Default for all SFGs Call by Call Incoming Type...
Page 57
Document Revison 1 Elite IPK ___________________________________________________________________________________ LK 1 System Mode LK 12 ACD/UCD Data Memory Block Name Default Value Programming Values ACD/UCD Group Pilot Number Not Specified Any Unused Extension Number Assignment ACD/UCD Group Overflow Not Specified Any Unused Extension Number Destination Assignment ∞...
Page 58
Elite IPK Document Revision 1 ___________________________________________________________________________________ LK 1 System Mode LK 14 ARS Data Memory Block Name Default Value Programming Values ARS Allow/Deny Selection NO, YES ARS Dialing Assignment None Tables 1~4. ARS Dial Allow/Deny Selection YES, NO ARS Route Table Number Table 1~4, Dial No.
Page 59
Document Revison 1 Elite IPK ___________________________________________________________________________________ LK 1 System Mode LK 15 K-CCIS (Continued) Data Memory Block Name Default Value Programming Values K-CCIS Message Response 30 sec Valid Times: 01~99 Seconds Timeout Assignment Link Reconnect Allow/Deny NO, YS Selection K-CCIS Maximum Call Forwarding Hop Assignment Calling Name display Allow/Deny NO, YS...
Page 60
Elite IPK Document Revision 1 ___________________________________________________________________________________ LK 1 System Mode LK 16 HUB (Continued) Data Memory Block Name Default Value Programming Values High Priority RX Tag Assignment (Lowest) 0~7 (Highest) High Priority TX Tag Assignment (Lowest) 0~7 (Highest) Low Priority TX Tag Assignment (Lowest) 0~7 (Highest) Port Mirroring Selection NO (Normal)
Page 61
Document Revison 1 Elite IPK ___________________________________________________________________________________ LK 3 CO/PBX Line Mode Data Memory Block Name Default Value Programming Values Trunk Name/Number Assignment Not Specified Maximum of 13 digits (numbers, hyphens, and spaces) Trunk Status Selection OUT&IN OUT&IN, IN Trunk-to-Trunk Group Assignment Refer to 3-03 Trunk-to-Trunk Group Assignment on page...
Page 62
Elite IPK Document Revision 1 ___________________________________________________________________________________ LK 3 CO/PBX Line Mode (Continued) Data Memory Block Name Default Value Programming Values Tie Line Length of Wink Signal In milliseconds: 30, 60, 90, 120, 150, 180, 210, 240, 270, Selection 300, 330, 360, 390, 420, 450, 480 Tie Line Length of Delay Signal In milliseconds: 0, 300, 600, 900, 1200, 1500, 1800, 2100,...
Page 63
Document Revison 1 Elite IPK ___________________________________________________________________________________ LK 3 CO/PBX Line Mode (Continued) Data Memory Block Name Default Value Programming Values Caller ID Display Assignment for Not Specified CO/PBX Line Live Record Trunk Selection NO = No Live Recording YS = Live Recording ISDN Line SPID Assignment Not Specified Up to 20 digits...
Page 64
Elite IPK Document Revision 1 ___________________________________________________________________________________ LK 4 Telephone Mode Data Memory Block Name Default Value Programming Values CO/PBX Ring Assignment (Day Refer to 4-01 CO/ No Ring, Immediate Ring, Delayed Ring Mode) PBX Ring Assignment (Day Mode) on page 2-449.
Page 65
Document Revison 1 Elite IPK ___________________________________________________________________________________ LK 4 Telephone Mode (Continued) Data Memory Block Name Default Value Programming Values Station Name Assignment Not Specified Up to six digits (characters) Trunk Outgoing Restriction LEDs Off Off = Not Restricted On = Restricted Prime Line/Hot Line Assignment Not Specified Up to 10 digits...
Page 66
Elite IPK Document Revision 1 ___________________________________________________________________________________ LK 4 Telephone Mode (Continued) Data Memory Block Name Default Value Programming Values Caller ID Preset Dial Outgoing CO Not Specified Selection Live Record Auto Delete Selection YS, NO ISDN Directory Number Selection YES, NO Caller ID Display for CAR Key 00 (Not Specified) Refer to the Memory Block Description.
Page 67
Document Revison 1 Elite IPK ___________________________________________________________________________________ LK 4 Telephone Mode (Continued) Data Memory Block Name Default Value Programming Values IP Station Number Assignment Blank 00~99, 000~999, 0000~9999 LCD Line Key – Name Assignment LK01~08:CO01~08 Name: Up to 8 characters. SLT Data Line Security Assignment NORMAL NORMAL, DATA Telephone Ringing Variation...
Elite IPK Document Revision 1 ___________________________________________________________________________________ LK 5 Trunk Group Mode Data Memory Block Name Default Value Programming Values Digit Add/Del for Tie Line Delete up to two digits Add up to two digits Networking Assignment (No Add or Delete) Tie Line Networking Tandem All Trunk Groups On = Enable...
Elite IPK Document Revision 1 ___________________________________________________________________________________ LK 8 Special Mode Data No. Memory Block Name Default Value Programming Values ROM Version Confirmation System Speed Dial Memory Clear Station Speed Dial Memory Clear Second Initialization Clock/Calendar Setting ___________________________________________________________________________________ Programming Manual 1 - 39...
Page 71
Document Revison 1 Elite IPK ___________________________________________________________________________________ THIS PAGE INTENTIONALLY LEFT BLANK ___________________________________________________________________________________ 1 - 40 Multiline Terminal Programming...
Memory Blocks C h a p t e r 2 ___________________________________________________________________________________ ECTION ROGRAMMING YSTEM SING THE EMORY LOCK This section provides detailed instructions for programming individual Memory Blocks. The Memory Blocks are listed numerically. For each Memory Block, the following information is provided. General Description is a brief explanation of the function of the Memory Block.
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-1-00 Pause Time Selection System Mode General Description Submode Use this Memory Block to specify the time of the pause that can be inserted between digits dialed on CO/PBX and Tie lines. Data No. Display D a t a D a t a...
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-01 DP Interdigit Time Selection System Mode General Description Submode The DP Interdigit Time is the minimum pause time between Dial Pulses. Use this Memory Block to Select either Pattern A or Pattern B. Data No.
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-1-02 Hookflash Time Selection System Mode General Description Submode Use this Memory Block to specify the loop open time for a hookflash signal sent to the CO or PBX when the Recall key on a Multiline Terminal is pressed. A Single Line Telephone (SLT) generates a hookflash to the CO or PBX line when a Single Line Data No.
Page 76
Elite IPK Document Revision 1 ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-1-46 Access Code (1-Digit) Assignment 1-1-47 Access Code (2-Digit) Assignment 1-3-02 SLT Hookflash Signal Selection 4-24 SLT Hookflash Assignment Notes A 1- or 2-digit Access Code can be assigned in Memory Block 1-1-46/47 [Access Code (1- or 2-Digit) Assignment] for Single Line Telephones to send a hookflash signal on a CO/PBX line (default: 6 #).
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-1-03 Hold Recall Time Selection System Mode (Non-Exclusive Hold) Submode General Description Use this Memory Block to specify the time a Non-Exclusive Hold outside call is held Data No. before a recall tone is generated. When no Limit is selected, the hold recall alarm tone is not generated.
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-04 Automatic Redial Time Selection System Mode General Description Submode When a called party is busy, the station user dials an Access Code and restores the handset. Use this Memory Block to define the redial timing parameters when automatic redial is set to a busy CO/PBX number.
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-1-05 Start Time Selection System Mode General Description Submode Use this Memory Block to specify the time after dialing before the system starts the Elapsed Call Time. Data No. Display S e t t i n g D a t a PC Programming D a t a...
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-06 CO/PBX Incoming Ringing Alarm System Mode Time Selection Submode General Description Use this Memory Block to specify the time between when a CO/PBX call is detected Data No. and the ringing tone changes to a higher pitch when the call is not answered. When No Limit is selected, the ringing tone does not change.
Page 81
Document Revison 1 Elite IPK ___________________________________________________________________________________ Notes Memory Blocks 4-01 and 4-02 [CO/PBX Ring Assignment (Day Mode/Night Mode)] must be set to ring. CO/PBX lines assigned for DIT/ANA do not activate this feature. Tie/DID lines assigned for Delayed Ringing follow this assignment after the delayed ringing starts. This feature uses the same ringing tone (Low, Medium, High) that is selected in Memory Blocks 3-07 (CO/PBX Ringing Variation Selection) and 4-91 (Telephone Ringing Variation Selection).
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-07 Tie Line Delay Ringing Time Selection System Mode General Description Submode Use this Memory Block to specify the time before a Tie line call ringing at a station can begin ringing at other preassigned stations when it is not answered in a programmed time.
Page 83
Document Revison 1 Elite IPK ___________________________________________________________________________________ Notes Example: ¤ System 1 System 2 ¤ ¤ Electra Elite Electra Elite Electra Elite (A) 100 (C) 102 System I IPK System II Elite IPK ¤ ¤ System I (B) 101 (B) 101 ¤...
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-09 Manual Pause Selection System Mode General Description Submode Use this Memory Block to specify either Pause Insertion or Last Number Dialed/Speed Dial to be executed using the Redial key when it is pressed after one or more digits of a dialed number are entered.
Page 85
Document Revison 1 Elite IPK ___________________________________________________________________________________ Notes When a user seizes a CO/PBX line and dials 907 4000 + + 12345 with this Memory Block set to NO, the system interprets the sequence as: 9074000XXX345 (XXX = and 12 is interpreted as Speed Dial buffer 12). When a user seizes a CO/PBX line and dials 907 4000 + + 12345 with this Memory Block set to YS, the system interprets the sequence as:...
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-11 System Transfer/Camp-On Selection System Mode General Description Submode Use this Memory Block system-wide to select whether or not the station user can press the Transfer key to perform a Ring Transfer or Station Camp-On. Data No.
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-1-12 Station Transfer/Camp-On Recall System Mode Time Selection Submode General Description Use this Memory Block to specify the time before a Ring Transfer or Station Camp-On Data No. from a station (without an Attendant Add-On Console) recalls back to the originating station when the call is not answered.
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-13 CO Transfer Ring Pattern Selection System Mode General Description Submode Use this Memory Block to select a Ring Pattern for CO transfers. Display Data No. S e t t i n g D a t a D a t a N o .
Page 89
Document Revison 1 Elite IPK ___________________________________________________________________________________ The Ring Patterns are shown in the table below: s= seconds Line Pattern Tone LK 1 Tone LK 2 LK 3 LK 4 LK 5 LK 6 LK 7 LK 8 LK 1 (Pg. 2) LK 2 (Pg.
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-14 CO Transfer Ring Tone Selection System Mode General Description Submode Use this Memory Block to select a ring tone for CO transfers. Display Data No. S e t t i n g D a t a T i t l e N o .
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-1-18 System Speed Dial Restriction by System Mode Tenant Submode General Description Use this Memory Block to specify whether or not System Speed Dial is restricted for Data No. each tenant. Display PC Programming S t a r t i n g S p e e d D i a l T e n a n t...
Page 92
Elite IPK Document Revision 1 ___________________________________________________________________________________ Programming Procedures 3 Press the corresponding CO/PBX line key to change the tenant number. Default Values Speed Dial buffers have the nine groups listed in the table below. All System Speed Dial buffers can be dialed from any tenant.
Page 93
Document Revison 1 Elite IPK ___________________________________________________________________________________ Notes One or more tenants can be enabled to use each group. Use this Memory Block to assign which tenants use each group. When speed dial is set to 1000, 900~999 cannot be restricted. The X in each Speed Dial Buffer No.
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-20 DID Digit Length Selection System Mode General Description Submode Use this Memory Block to define the number of Direct Inward Dialing (DID) digits in Memory Block 1-1-22 (DID Digit Conversion Table). Data No. Display S e t t i n g D a t a...
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-1-21 DID Digit Conversion Assignment System Mode General Description Submode Use this Memory Block to enable the DID Digit Conversion Table, Memory Block 1-1-22 (DID Digit Conversion Table), for each number. Data No. Display PC Programming D a t a S e t t i n g...
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-22 DID Digit Conversion Table System Mode General Description Submode Up to 200 incoming DID numbers can be assigned individually to ring at a preassigned 2-digit, 3-digit, or 4-digit station number, closed number (plus outgoing digits), or tenant number (00~47) for day mode or night mode.
Page 97
Document Revison 1 Elite IPK ___________________________________________________________________________________ Programming Procedures (Continued) 4 Press to write the data and display the next Memory Block. 5 Program the next Memory Block or press to go back on-line. Related Programming M.B. Number Memory Block Name 1-1-20 DID Effective Digit Selection 1-1-21...
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-23 DID Forward Station Number for System Mode Busy Station or Undefined Digit Submode General Description Use this Memory Block when Memory Block 1-1-22 (DID Digit Conversion Table) is Data No. enabled to define where digits are routed when undefined or the station is busy. Display PC Programming +ALN...
Page 99
Document Revison 1 Elite IPK ___________________________________________________________________________________ Notes When this Memory Block is set to a Tenant, the following must be assigned to ring the desired station: Memory Block 4-01 [CO/PBX Ring Assignment (Day Mode)] Memory Block 4-02 [CO/PBX Ring Assignment (Night Mode)] Memory Block 4-09 (Telephone to Tenant Assignment).
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-24 PBX/CTX Access Code Assignment I System Mode General Description Submode Use this Memory Block to specify a PBX line PBX/CTX Access Code together with pauses for outgoing calls. Data No. Display S e t t i n g D a t a PC Programming T i t l e...
Page 101
Document Revison 1 Elite IPK ___________________________________________________________________________________ Notes ¤ Example: Elite IPK System Elite IPK System PBX Line CO Line Intercom Line Features such as Code Restriction do not operate properly unless a PBX/CTX Access Code is specified. This limitation applies to PBX lines assigned in Memory Block 3-91 (Trunk Type Selection). A pause is not inserted in the number of an outgoing call on a CO line.
Page 102
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-25 PBX/CTX Access Code Assignment II System Mode General Description Submode Use this Memory Block to specify a second PBX line PBX/CTX Access Code together with pauses for outgoing calls. Data No. Display D a t a S e t t i n g PC Programming T i t l e...
Page 103
Document Revison 1 Elite IPK ___________________________________________________________________________________ Notes ¤ Example: Elite IPK System Elite IPK System PBX Line Tie Line Intercom Line Features such as Code Restriction do not operate properly unless a PBX/CTX Access Code is specified. This limitation only applies to PBX lines assigned in Memory Block 3-91 (Trunk Type Selection). A pause is not inserted in the number of an outgoing call on a CO line.
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-27 Automatic Day/Night Mode Switching System Mode Time Assignment Submode General Description Use this Memory Block to assign a start time for Pattern 1 and a different start time for Data No. Pattern 2 to automatically switch between Day Mode and Night Mode. Display PC Programming D a y M o d e...
Page 105
Document Revison 1 Elite IPK ___________________________________________________________________________________ Related Programming (Continued) M.B. Number Memory Block Name 4-17 Station to Class of Service Feature Assignment 4-37 Extension Line Key Ring Assignment (Day Mode) 4-38 Extension Line Key Ring Assignment (Night Mode) Notes The start time for Day Mode or Night Mode can be programmed to automatically switch modes at the specified times.
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-28 Distinctive Ringing by Telephone or System Mode CO Selection Submode General Description Use this Memory Block to assign a distinctive ringing tone for each telephone or each Data No. CO/PBX line. Display PC Programming +BTS D a t a S e t t i n g...
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-1-29 Private Line Assignment System Mode General Description Submode Use this Memory Block to assign an outside line as a private line. The private line cannot be seized by any other telephone, and an LED indication is not provided to other terminals.
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-30 Route Advance Block Assignment System Mode General Description Submode Use this Memory Block to assign a priority level (1~4) to each Trunk group assigned in a Route Advance Block. The system has 32 blocks that can be specified. Data No.
Page 109
Document Revison 1 Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 3-03 Trunk-to-Trunk Group Assignment Notes When 00 (Not Set) is programmed, no trunks are accessed for this priority setting. When Route Advance Block Numbers are assigned and a line key is pressed or an Access Code is dialed, the system starts searching for an idle line in a specified group (beginning with the Trunk group assigned priority 1).
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-32 Automatic Day/Night Mode by Day of System Mode Week Selection Submode General Description Use this Memory Block to select either Pattern 1 or Pattern 2 Day/Night Mode start Data No. time for each day of the week. Memory Block 1-1-27 (Automatic Day/Night Mode Switching Time Assignment) sets Day/Night Mode start time for Pattern 1 and Pattern 2 to switch the system between Day Mode and Night Mode.
Page 111
Document Revison 1 Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-1-27 Automatic Day/Night Mode Switching Time Assignment 1-8-07 Class of Service (Attendant) Feature Selection 1 1-8-48 Automatic Daylight Saving Time Selection 4-09 Telephone to Tenant Assignment 4-17 Station to Class of Service Feature Assignment Notes By designating two time settings in Memory Block 1-1-27 (Automatic Day/Night Mode Switching Time...
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-33 Speed Dial Number/Name Display System Mode Selection Submode General Description Use this Memory Block to specify whether the dialed number or name is displayed first Data No. on the LCD of the originating station when an outgoing call is made using Speed Dial. Display PC Programming D a t a...
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-1-34 Tie Line First Ring Pattern Selection System Mode General Description Submode Use this Memory Block to set a specific ringing pattern for incoming calls on Tie lines. After a delay interval specified in Memory Block 1-1-07 (Tie Line Delay Ringing Time Selection), a Tie call can ring at all Day/Night ring-assigned telephones using a Data No.
Page 114
Elite IPK Document Revision 1 ___________________________________________________________________________________ Ringing Pattern Selection s= seconds Pattern Same as Internal Ring Voice Announce ___________________________________________________________________________________ Programming Manual 2 - 43...
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-1-35 Speed Dial Buffer Allocation System Mode General Description Submode Use this Memory Block to specify either 100-memory or 1000-memory allocation. Display Data No. S e t t i n g D a t a D a t a T i t l e T i t l e...
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-37 Trunk Queuing Timeout Selection System Mode General Description Submode Use this Memory Block to specify the time that a station with Trunk Queue set rings, before the queue is automatically canceled. Data No. Display S e t t i n g D a t a...
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-1-46 Access Code (1-Digit) Assignment System Mode General Description Submode Use this Memory Block to assign a 1-digit number as an Access Code or station number. Data No. Display D i a l N o . D a t a F u n c t i o n PC Programming...
Page 118
Elite IPK Document Revision 1 ___________________________________________________________________________________ Notes Select options from the list of function numbers in Memory Block 1-1-46 [Access Code (1-Digit) Assignment], and assign a number (from 0~9), , or to each selected function. When a function is assigned a 1-digit Access Code, 2-digit Access Codes with the same first digit become invalid (i.e., if a function is assigned to Access Code 5, Access Codes 50~59, 5 , and 5 cannot be used).
Page 119
Document Revison 1 Elite IPK ___________________________________________________________________________________ Default Function Default Function Function Name Function Name Dial No. Dial No. Call Pickup CO/PBX by Tenant All External Zone Paging (1-digit) External Zone A Paging Call Pickup CO/PBX/Centrex by External Zone B Paging Tenant (2-digit) External Zone C Paging Specified Tenant Internal Paging...
Page 120
Elite IPK Document Revision 1 ___________________________________________________________________________________ Default Function Default Function Function Name Function Name Dial No. Dial No. Trunk Group 01 Call Forward - Busy/ No Answer Split Cancel Trunk Group 02 Call Forward - All Split Set Trunk Group 03 Call Forward - All Split Cancel Trunk Group 04 Call Forward - Busy/No Answer Split...
Page 121
Document Revison 1 Elite IPK ___________________________________________________________________________________ Default Function Default Function Function Name Function Name Dial No. Dial No. Specified Station Access Code Closed Number Block 1 Specified Station Access Code Specified Station Access Code Closed Number Block 16 Not Used VRS Voice Message Record/Verify/ 201~232 Route Advance Block 01~32...
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-47 Access Code (2-Digit) Assignment System Mode General Description Submode Use this Memory Block to assign a 2-digit number as an Access Code. Display Data No. D i a l N o . D a t a F u n c t i o n 0 ~ 9 T i t l e...
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-1-48 Access Code (3-Digit) Assignment System Mode General Description Submode Use this Memory Block to assign a 3-digit number as an Access Code. Display Data No. T h i r d D i g i t T a b l e D i a l N o .
Page 124
Elite IPK Document Revision 1 ___________________________________________________________________________________ Notes Select options from the list of function numbers in Memory Block 1-1-46 [Access Code (1-Digit) Assignment], and assign a 3-digit Access Code. When a function is assigned a 1-digit Access Code or 2-digit Access Code, 3-digit Access Codes (with the same first digit) become invalid (i.e., if a function is assigned to Access Code 5, Access Codes 50~59, 5 , and 5 cannot be used).
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-1-49 Networking Trunk Group/Route System Mode Advance Assignment Submode General Description Use this Memory Block to assign the function number of the Trunk Group to be used to Data No. network an Electra Elite 48/192 system to another system by Tie lines or CO/PBX/ CTX lines.
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-50 CO/PBX Outgoing Digit Add System Mode Assignment Submode General Description Use this Memory Block to specify up to 10 additional digits when a trunk in the Trunk Data No. group or Route Advance block assigned in Memory Block 1-1-49 (Networking Trunk Group/Route Advance Assignment) is seized, and a number is dialed.
Page 127
Document Revison 1 Elite IPK ___________________________________________________________________________________ Notes Example: Station 100 Add 200 Dials 200 ¤ System System ¤ Station 200 Rings To assign System 1 in System Programming: Memory Block 1-1-46 [Access Code (1-Digit) assignment]. Assignment 2 → 401 (Closed Number Block 01). Memory Block 1-1-49 (Networking Trunk Group/Route Advance Assignment).
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-51 CO Line Ringing Pattern Selection System Mode General Description Submode Use this Memory Block to assign the initial ringing pattern or no ring for incoming calls on a CO line. Data No. Display S e t t i n g D a t a P a g e...
Page 129
Document Revison 1 Elite IPK ___________________________________________________________________________________ The Ring Patterns are shown in the table below: s= seconds Pattern No Ring ___________________________________________________________________________________ 2 - 58 Memory Blocks...
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-52 PBX Line Ringing Pattern Selection System Mode General Description Submode Use this Memory Block to assign the initial ringing pattern or no ring for incoming calls on a PBX line. Data No. Display PC Programming P a g e S e t t i n g...
Page 131
Document Revison 1 Elite IPK ___________________________________________________________________________________ The Ring Patterns are listed in the table below: s= seconds Pattern No Ring ___________________________________________________________________________________ 2 - 60 Memory Blocks...
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-53 Tie Line Delay Ring Pattern Selection System Mode General Description Submode Use this Memory Block to select a ringing pattern or no ring for incoming calls on a Tie line after the timeout set in Memory Block 1-1-07 (Tie Line Delay Ringing Time Selection).
Page 133
Document Revison 1 Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-1-07 Tie Line Delay Ringing Time Selection 1-1-34 Tie Line First Ring Pattern Selection 4-01 CO/PBX Ring Assignment (Day Mode) 4-02 CO/PBX Ring Assignment (Night Mode) The Ring Patterns are shown in the table below: s= seconds Pattern No Ring...
Memory Block. 5 Program the next Memory Block or press to go back on-line. Related Programming Refer to individual features in the Electra Elite IPK Features and Specifications Manual. ___________________________________________________________________________________ Programming Manual 2 - 63...
Page 135
Document Revison 1 Elite IPK ___________________________________________________________________________________ The Ring Patterns are shown in the table below: s= seconds Pattern No Ring ___________________________________________________________________________________ 2 - 64 Memory Blocks...
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-55 DID Line Ringing Pattern Selection System Mode General Description Submode Use this Memory Block to assign the ringing pattern or no ring to be used for DID calls. Display Data No. D a t a S e t t i n g P a g e N o .
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-1-57 CO/PBX Prepause Time Selection System Mode General Description Submode Use this Memory Block to assign a pause time before dialed digits can be sent over a CO/PBX line after the trunk is seized by a system user. Data No.
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-59 Synchronous Ringing Selection System Mode General Description Submode Use this Memory Block to specify whether or not CO/PBX calls follow Synchronous Ringing. Data No. Display D a t a S e t t i n g PC Programming N o .
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-1-60 8-Digit Matching Table Assignment System Mode General Description Submode Use this Memory Block to assign the outgoing dial digit for Code Restriction (except OCC Dial Digit - Normal Dial). Program this assignment in one of two ways: Data No.
Page 140
Elite IPK Document Revision 1 ___________________________________________________________________________________ Programming Procedures Operation data includes: Operation Dial Number Operation Data a nd 5 Press to write the data and advance to the next Dial Code. After all Dial Codes for 8-Digit Matching Table 00 are entered, press again to display 8 Digit Matching Table 01.
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-1-61 8-Digit Matching Table to Class System Mode Assignment Submode General Description Use this Memory Block to program each 8-digit Matching Table to allow or deny Data No. assignment per class. Classes 00 and 15 are fixed. Only classes 01 14 can be programmed.
Page 142
Elite IPK Document Revision 1 ___________________________________________________________________________________ Table 00 Class YS = Allow NO = Deny NON = Blank ___________________________________________________________________________________ Programming Manual 2 - 71...
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-1-62 System Speed Dial Override by Class System Mode Selection Submode General Description Use this Memory Block to specify per Class whether or not Class Selection can Data No. override System Speed Dial. Display PC Programming C l a s s D a t a...
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-63 Hold Recall Time Selection System Mode (Exclusive) Submode General Description Use this Memory Block to specify the time for Exclusive Hold Recall. If No Limit is Data No. selected, Exclusive Hold Recall is not provided. Display PC Programming D a t a...
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-1-64 Attendant Add-On Console Transfer/ System Mode Camp-On Recall Time Selection Submode General Description Use this Memory Block to specify the time before a Ring Transfer or Station Camp-On Data No. from a station with an Attendant Add-On Console recalls back to the originating station when the call is not answered.
Page 146
Elite IPK Document Revision 1 ___________________________________________________________________________________ Notes When a station without an assigned Attendant Add-On Console transfers or camps-on a call to a station that goes unanswered, the call recalls using Memory Block 1-1-12 (Station Transfer/Camp-On Recall Time Selection). Time is valid only for stations assigned an Attendant Add-On Console in Memory Block 1-6-01 (Attendant Add-On Console to Telephone Port Assignment).
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-1-65 Code Restriction Class Allow/Deny System Mode Selection Submode General Description Use this Memory Block to assign Code Restriction Classes as Allow or Deny. Data No. 0 1 ~ 1 4 This assignment is used when there is no match or there is an overlap (duplicate numbers in tables with opposite assignments) of numbers in the 8-Digit Matching Tables.
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-66 8-Digit Matching Table to Normal System Mode Dial Assignment Submode General Description Use this Memory Block to assign the 8-Digit Matching Table by class for normal dialing Data No. as used or unused. When unused is assigned, the system does not check during normal dialing even when Memory Block 1-1-61 (8-Digit Matching Table to Class Assignment) is programmed.
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-1-67 OCC Table Assignment System Mode General Description Submode Use this Memory Block to assign an Other Common Carrier (OCC) code (8-digit maximum) in a table. A maximum of 16 codes can be assigned. Data No.
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-68 8-Digit Matching Table to OCC Table System Mode Assignment Submode General Description Use this Memory Block to assign each 8-Digit Matching Table to each Other Common Data No. Carrier (OCC) Code Table. Display PC Programming O C C D a t a...
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-1-69 Tie Line Code Restriction Assignment System Mode General Description Submode Use this Memory Block to restrict outgoing Tie line dialed digits. Display Data No. D a t a S e t t i n g N o .
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-70 Code Restriction Class Assignment System Mode When Lockout is Set Submode General Description Use this Memory Block to assign the Code Restriction Class when a station user sets Data No. the Station Outgoing Lockout or when the Attendant sets Attendant Station Outgoing Lockout.
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-1-71 First Delay Announcement Start Time System Mode Selection Submode General Description Use this Memory Block to specify the time between receiving a CO call and sending a Data No. First Delay Announcement to the calling party. Display PC Programming S e t t i n g...
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-72 First Delay Announcement Repeat System Mode Selection Submode General Description Use this Memory Block to specify the number of times a First Delay Announcement is Data No. repeated. Display PC Programming D a t a S e t t i n g N o .
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-1-73 First to Second Delay Announcement System Mode Interval Time Selection Submode General Description Use this Memory Block to specify the time between the end of the First Delay Data No. Announcement sending time and the start time of the Second Delay Announcement. Display PC Programming D a t a...
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-74 Second Delay Announcement Repeat System Mode Selection Submode General Description Use this Memory Block to specify the number of times a Second Delay Announcement Data No. is repeated. Display PC Programming D a t a S e t t i n g N o .
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-1-75 Second Delay Announcement Repeat System Mode Interval Time Selection Submode General Description Use this Memory Block to specify the interval time to repeat Second Delay Data No. Announcement to the calling party. Display PC Programming S e t t i n g D a t a...
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-76 Barge-In Alert Tone Assignment System Mode General Description Submode Use this Memory Block to specify whether or not Barge-In Alert Tone is allowed. Display Data No. S e t t i n g D a t a T i t l e D a t a...
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-1-77 Delayed Ringing Time Assignment System Mode (CO) Submode General Description Use this Memory Block to assign the delayed ringing time for incoming outside line Data No. calls. Display PC Programming +BCM D a t a S e t t i n g T i t l e N o .
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-78 Caller ID Display Assignment for System Mode System Mode Submode General Description Use this Memory Block to assign up to 15 Multiline Terminals to display ANI/Caller ID Data No. Indication for normal incoming CO/PBX calls or CO/PBX calls ringing a Call Arrival (CAR) key.
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-1-79 BGM Port Assignment System Mode General Description Submode Use this Memory Block to assign the CO/PBX port as a Background Music port. Display Data No. D a t a C O N o . T i t l e N o .
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-80 ISDN DTMF Duration/Interdigit System Mode Selection Submode General Description Use this Memory Block to specify tone duration/interdigit time of Dual - Tone Data No. Multifrequency (DTMF) signals for the ISDN trunk. Display PC Programming S e t t i n g D a t a D a t a...
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-1-81 ISDN Dial Interval Time Selection System Mode General Description Submode Use this Memory Block to specify the time between each digit dialed before digits are sent over the Network. Data No. Display S e t t i n g D a t a D a t a N o .
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-1-82 CO Feature Code Service for Code System Mode Restriction Submode General Description Use this Memory Block to define a code to send to the CO in front of the dialed Data No. number to allow completion of a CO call made to a Code restricted number set to allow.
Page 165
Document Revison 1 Elite IPK ___________________________________________________________________________________ THIS PAGE INTENTIONALLY LEFT BLANK ___________________________________________________________________________________ 2 - 94 Memory Blocks...
Electra Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-2-00 Internal Paging Timeout Selection System Mode General Description Submode Use this Memory Block to specify the time allowed for paging. Display Data No. S e t t i n g D a t a...
Document Revison 1 Electra Elite IPK ___________________________________________________________________________________ 1-2-01 Intercom Call Voice/Tone Signal System Mode Selection Submode General Description Use this Memory Block to specify whether signal tone or voice is used first for an Data No. intercom call. Display PC Programming...
Electra Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-2-02 Automatic Callback Release Time System Mode Selection Submode General Description Use this Memory Block to specify the time allowed for an automatic callback before Data No. the request is automatically canceled. Display...
Page 169
Document Revison 1 Electra Elite IPK ___________________________________________________________________________________ 1-2-03 2-, 3-, or 4-Digit Station Number System Mode Selection Submode General Description Use this Memory Block to determine the number of digits for station numbers. Either Data No. 2-digit (00~99), 3-digit (000~999), or 4-digit (0000~9999) assignment is available.
Memory Block. 5 Program the next Memory Block or press to go back on-line. Related Programming Refer to individual features in the Electra Elite IPK Features and Specifications Manual. ___________________________________________________________________________________ Programming Manual 2 - 99...
Page 171
The total number of shared and CAR ports are shared with PS ports. The Electra Elite IPK basic (48) system allows a maximum of 32 ports to be shared by Legacy stations (ESI, SLI, FMS/VMS, and OPX) and Call Arrival Keys. In addition to the shared ports, 40 dedicated CAR ports can also be defined.
Electra Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-2-08 Specified Station Access Code System Mode Assignment Submode General Description Use this Memory Block to assign specific stations for abbreviated dialing. Up to 24 Data No. stations can be assigned. Display PC Programming...
Page 173
Document Revison 1 Electra Elite IPK ___________________________________________________________________________________ Notes Specified stations can be accessed from intercom (ICM) dial tone or as an outside caller calling into the Electra Elite IPK system Auto Attendant. The Specified Access Code is assigned in Memory Blocks 1-1-46 or 1-1-47 [Access Code (1-Digit/2-Digit) Assignment].
Electra Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-2-09~18 Customized Message 1~10 System Mode Assignment Submode General Description Use this Memory Block to program various messages for display at a station LCD. Data No. When a user places an intercom (ICM) call from a station equipped with an LCD...
Page 175
Document Revison 1 Electra Elite IPK ___________________________________________________________________________________ 1-2-19 Intercom Ring Pattern Selection System Mode General Description Submode Use this Memory Block to select a ring pattern or turn the tone ON/OFF when intercom calls are made. Data No. Display S e t t i n g...
Page 176
Electra Elite IPK Document Revision 1 ___________________________________________________________________________________ The Ring Patterns are listed in the table below: s= seconds Line Pattern LK 1 LK 2 LK 3 LK 4 LK 5 LK 6 LK 7 LK 8 LK 1 (Pg. 2) LK 2 (Pg.
Document Revison 1 Electra Elite IPK ___________________________________________________________________________________ 1-2-20 Intercom Ring Tone Selection System Mode General Description Submode Use this Memory Block to select a ring tone for intercom calls. Display Data No. S e t t i n g D a t a...
Electra Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-2-21 PS Telephone Block Assignment System Mode General Description Submode Use this Memory Block to specify the number of PS II stations that can be used in the system. Data No. Display S e t t i n g...
Page 179
The Electra Elite IPK expanded system can support a maximum of 40 PS II stations. The Electra Elite IPK basic system can have 32 ports to be shared by station ports (ESI, SLI, FMS/VMS, CNF, and OPX), Call Arrival Keys, and PS stations. If 24 station ports are being used, eight remain for use as PS stations.
Electra Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-2-22 Call Forward - No Answer Time System Mode Selection Submode General Description Use this Memory Block to specify the time before incoming intercom calls or incoming Data No. CO/PBX lines are forwarded to another station number when the called party does not answer.
Document Revison 1 Electra Elite IPK ___________________________________________________________________________________ 1-2-23 System Call Park Recall Time System Mode Selection Submode General Description Use this Memory Block to specify the time before a CO/PBX call recalls back to a Data No. station from Call Park.
Electra Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-2-24 Intercom Feature Access Code System Mode Assignment Submode General Description Use this Memory Block to assign the Access Code for Voice/Tone change or Step Data No. Call. Display PC Programming S e t t i n g...
Page 183
Document Revison 1 Electra Elite IPK ___________________________________________________________________________________ Related Programming M.B. Number Memory Block Name 1-2-01 Intercom Call Voice/Tone Signal Selection 1-8-08 Class of Service (Station) Feature Selection 2 1-8-26 Voice Mail Quick Transfer Master Hunt Number 4-17 Station to Class of Service Feature Assignment Notes Features can be assigned to more than one dial number.
Electra Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-2-25 Internal Paging Alert Tone Selection System Mode General Description Submode Use this Memory Block to specify whether or not a call alert tone is provided when Internal Paging is used. Data No.
Document Revison 1 Electra Elite IPK ___________________________________________________________________________________ 1-2-26 Delayed Ringing Time Assignment System Mode (ICM) Submode General Description Use this Memory Block to specify the delayed ringing time for incoming internal calls. Data No. Display PC Programming S e t t i n g...
Electra Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-2-30 PS Out of Area Time Assignment System Mode General Description Submode Use this Memory Block to specify the retry time when a PS II is Out of Area. Display Data No. D a t a...
Document Revison 1 Electra Elite IPK ___________________________________________________________________________________ 1-2-32 IP Phone Block Assignment System Mode General Description Submode Use this Memory Block to specify the number of IP Phones that can be used with the IPCA( )-U( ) ETU (CPU board) Data No.
Page 188
The total number of shared and CAR ports are shared with PS ports. The Electra Elite IPK Basic Port Package (48) allows a maximum of 32 ports to be shared by stations (ESI, SLI, FMS/VMS, and OPX) and Call Arrival Keys. In addition to the shared ports, 40 dedicated CAR ports can also be defined.
Page 189
Document Revison 1 Electra Elite IPK ___________________________________________________________________________________ THIS PAGE INTENTIONALLY LEFT BLANK ___________________________________________________________________________________ 2 - 118 Memory Blocks...
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-3-01 Bounce Protect Time Selection System Mode General Description Submode Use this Memory Block to specify a time for detection of a valid 0ff-hook indication that is long enough to prevent an unintentional bounce of the receiver from being detected as a new off-hook indication from a Single Line Telephone or Voice Mail system.
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-3-02 SLT Hookflash Signal Selection System Mode General Description Submode Use this Memory Block to specify whether a line is held internally, or when behind a PBX, a hookflash (HF) signal is sent to the line when a Single Line Telephone user performs a hookflash.
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-3-03 First Digit PBR Release Time System Mode Selection Submode General Description Use this Memory Block to specify the time a Push Button Receiver (PBR) circuit is Data No. connected when a dual-tone multifrequency (DTMF) Single Line Telephone user goes off-hook.
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-3-04 Dial 1 (DP) Hookflash Selection System Mode General Description Submode Use this Memory Block to specify whether or not a dial pulse (DP) Single Line Telephone provides a hookflash signal when the user presses 1 during an intercom or CO/PBX call.
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-3-05 Hookflash Start Time Selection System Mode General Description Submode Use this Memory Block to specify the minimum hookflash time from a Single Line Telephone or analog Voice Mail system before it is detected as the beginning of a valid hookflash.
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-3-06 Hookflash End Time Selection System Mode General Description Submode Use this Memory Block to specify the maximum hookflash duration from a Single Line Telephone to receive a second dial tone. Data No. Display D a t a S e t t i n g P a g e...
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-3-07 Voice Mail Digit Add Assignment System Mode General Description Submode Use this Memory Block to assign up to four digits in front of the station number sent to the voice mail when a call is forwarded. Data No.
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-3-08 Voice Mail DTMF Delay Time System Mode Selection Submode General Description Use this Memory Block to specify the delay time before dual-tone multifrequency Data No. (DTMF) tones are sent from Voice Mail Interface (VMI) ports. Display PC Programming D a t a...
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-3-09 Voice Mail Disconnect Time Selection System Mode General Description Submode Use this Memory Block to specify the time a disconnect signal is sent to the voice mail system. Data No. Display S e t t i n g D a t a T i t l e D a t a...
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-3-10 Voice Mail DTMF Duration/Interdigit System Mode Time Selection Submode General Description Use this Memory Block to specify dual-tone multifrequency (DTMF) duration and Data No. interdigit time for voice mail. Display PC Programming S e t t i n g D a t a T i t l e D a t a...
5 Program the next Memory Block or press to go back on-line. Related Programming Refer to individual features in the Electra Elite IPK Features and Specifications Manual. Notes This block is used for Direct Inward System Access (DISA), Trunk-to-Trunk Transfer, Call Forward – Off-Premise, and Tie line tandem features.
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-4-01 Automated Attendant First Digit PBR System Mode Release Time Selection Submode General Description Use this Memory Block to specify the time a Push Button Receiver (PBR) remains Data No. connected after the Automated Attendant message is played when a calling party calls in through an Automated Attendant trunk.
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-4-02 Automated Attendant Transfer System Mode Delayed Ringing Time Selections Submode General Description Use this Memory Block to specify the time that a call rings at the destination station Data No. before the automated attendant rings a programmed station. Display PC Programming D a t a...
Page 203
Document Revison 1 Elite IPK ___________________________________________________________________________________ Notes Example: ¤ ( D) ¤ ¤ (A) 100 (C) 102 PSTN ¤ ¤ Elite IPK (B) 101 (B) 101 ¤ ¤ (C) 102 (A) 100 Trunk 1 Time Elapsed In this example, Public Switching Telephone Network (PSTN) and the system are connected by Trunk 1.
5 Program the next Memory Block or press to go back on-line. Related Programming Refer to individual features in the Electra Elite IPK Features and Specifications Manual. Notes When the called party does not answer in the programmed time, the call is dropped.
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-4-04 Tandem Transfer SMDR Print System Mode Extension Assignment Submode General Description Use this Memory Block to specify a special number to be output from Station Message Data No. Detail Recording (SMDR) to indicate an automatic trunk-to-trunk transfer. Display PC Programming S e t t i n g...
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-4-05 Automatic Tandem Trunk by Night System Mode Mode Selection Submode General Description Use this Memory Block to specify whether or not the Automatic Trunk-to-Trunk Data No. Transfer feature follows the Night Mode assignment. Display PC Programming S e t t i n g...
5 Program the next Memory Block or press to go back on-line. Related Programming Refer to individual features in the Electra Elite IPK Features and Specifications Manual. Notes When NORMAL is selected, and a DTMF tone is not received during the Automated Attendant message or...
5 Program the next Memory Block or press to go back on-line. Related Programming Refer to individual features in the Electra Elite IPK Features and Specifications Manual. Notes When FR is assigned, the Automated Attendant message send start time and the PBR connected to Automated Attendant trunk start time are the same.
NT (Night) and repeat Steps 3, 4, and 5 for all messages for night Mode. The next Memory Block is displayed. 7 Program the next Memory Block or press to go back on-line. Related Programming Refer to individual features in the Electra Elite IPK Features and Specifications Manual. ___________________________________________________________________________________ 2 - 138 Memory Blocks...
6 Program the next Memory Block or press to go back on-line. Related Programming Refer to individual features in the Electra Elite IPK Features and Specifications Manual. Notes When a tenant is not assigned to a specific automated message, the Automated Attendant sends the message assigned in Memory Block 1-4-11 (Automated Attendant Message Day/Night Mode Selection).
5 Repeat Steps 3 and 4 for all messages. The next Memory Block is displayed. 6 Program the next Memory Block or press to go back on-line. Related Programming Refer to individual features in the Electra Elite IPK Features and Specifications Manual. ___________________________________________________________________________________ 2 - 140 Memory Blocks...
7 Continue this cycle for all Dial NOs. for all messages. The next Memory Block is displayed. 8 Program the next Memory Block or press to go back on-line. Related Programming Refer to individual features in the Electra Elite IPK Features and Specifications Manual. ___________________________________________________________________________________ Programming Manual 2 - 141...
Page 213
Document Revison 1 Elite IPK ___________________________________________________________________________________ Notes Function 011 (Bypass Automated Attendant) uses Memory Blocks 4-01 [CO/PBX Ring Assignment (Day Mode)] and 4-02 [CO/PBX Ring Assignment (Night Mode)] to ring according to those assignments. Functions 015~016 (Ring Internal Paging Zone A/B/C) require assigning the following to ring the desired station: Memory Block 4-01 [CO/PBX Ring Assignment (Day Mode)] Memory Block 4-02 [CO/PBX Ring Assignment (Night Mode)] Memory Block 4-93 (Internal Zone Paging Selection).
Page 214
Elite IPK Document Revision 1 ___________________________________________________________________________________ Function Function Contents Contents Code Code Unregistered Not Used Automated Attendant Message (1) Not Used Automated Attendant Message (2) Not Used Automated Attendant Message (3) Specified Station Call (00). Refer to Memory Block 1-2-08 (Specified Station Access Code Assignment) Automated Attendant Message (4) Specified Station Call (01)
7 Program the next Memory Block or press to go back on-line. Related Programming Refer to individual features in the Electra Elite IPK Features and Specifications Manual. Notes To use default 52~54, ringing must be assigned in Memory Blocks 4-01 [CO/PBX Ring Assignment (Day Mode)] or 4-02 [CO/PBX Ring Assignment (Night Mode)] .
5 Repeat Steps 3 and 4 for each AA MSG. The next Memory Block is displayed. 6 Program the next Memory Block or press to go back on-line. Related Programming Refer to individual features in the Electra Elite IPK Features and Specifications Manual. ___________________________________________________________________________________ Programming Manual 2 - 145...
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-4-17 Automated Attendant Delay System Mode Announcement Hold Tone Selection Submode General Description Use this Memory Block to specify the tone to be sent to the outside party after the Data No. Automated Attendant Delay Announcements are played. Display PC Programming S e t t i n g...
Page 218
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-4-18 Automated Attendant Delay System Mode Announcement Assignment Submode General Description Use this Memory Block to specify the order for the Automated Attendant messages Data No. that are played in Delayed Announcement Mode. Display PC Programming S e t t i n g + AU...
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-4-19 Automated Attendant 1 to 2 Delay System Mode Announcement Interval Time Selection Submode Data No. General Description Use this Memory Block to specify the time, in seconds or minutes, between the Automated Attendant Delay Announcement messages. PC Programming + AU Display...
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-4-20 Automated Attendant Delay System Mode Announcement Disconnect Time Selection Submode Data No. General Description Use this Memory Block to establish the time, in seconds or minutes, the Automated Attendant rings the station before disconnecting the caller. This Memory Block only PC Programming applies when the Automated Attendant is set to Delay Announcement Mode.
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-4-21 Automated Attendant Extension System Mode Number Assignment Submode General Description Use this Memory Block to specify the Automated Attendant message to be played Data No. when a DID call is received. Display PC Programming + AU D a t a A A M S G...
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-4-22 Automated Attendant Direct System Mode Extension Ring Assignment Submode General Description Use this Memory Block to specify the Automated Attendant message to be played for Data No. direct transfer to the extension number. Display PC Programming + AU...
Page 223
Document Revison 1 Elite IPK ___________________________________________________________________________________ THIS PAGE INTENTIONALLY LEFT BLANK ___________________________________________________________________________________ 2 - 152 Memory Blocks...
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-5-02 SMDR Print Format System Mode General Description Submode Use this Memory Block to specify whether or not all digits are printed. When ALL is specified, all digits are printed. When MSK (Mask) is specified, the last four digits are masked and printed as XXXX.
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-5-13 Printer Connected Selection System Mode General Description Submode Use this Memory Block to program printer connection. When the printer is not connected to the system, an alarm sounds at stations connected to Ports 01 and 02. Data No.
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-5-14 Printer Line Feed Control Selection System Mode General Description Submode Use this Memory Block to specify the data format to be sent to the Station Message Detail Recording (SMDR) printer. When YS is set, a return is provided with the call record.
Page 227
Document Revison 1 Elite IPK ___________________________________________________________________________________ Notes Example: Settings to specify the format of communication data output to the printer. Line Feed control in effect. 07/03/92 09:00 08-05-12 OG 123 00:15:32 102885167537000 FWD234 12345678 No Line Feed control. 07/03/92 09:00 08-05-12 OG 123 00:15:32...
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-5-25 SMDR Valid Call Time Assignment System Mode General Description Submode Use this Memory Block to assign the minimum call time before the Station Message Detail Recording (SMDR) outputs a record of the outgoing CO/PBX call. Data No.
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-5-26 SMDR Incoming/Outgoing Print System Mode Selection Submode General Description Use this Memory Block to specify the call records to be output from the Station Data No. Message Detail Recording (SMDR): OUT = print outgoing call records only, INC = print incoming call records only, ALL = print incoming and outgoing call records.
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-6-01 Attendant Add-On Console to System Mode Telephone Port Assignment Submode General Description Use this Memory Block to assign an Attendant Add-On Console to a telephone port Data No. number. Display PC Programming +BTD D a t a D a t a D S S N o .
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-6-03 DSS Call Voice/Tone Signal Selection System Mode General Description Submode Use this Memory Block to specify whether Voice or Tone signaling is to be used first when calling an extension from an Attendant Add-On Console. Data No.
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-6-05 Attendant Add-On Console Key System Mode Selection Submode General Description Use this Memory Block to assign functions to the Attendant Add-On Console keys. Data No. Display PC Programming D S S B u t t o n D a t a N o .
Page 233
Document Revison 1 Elite IPK ___________________________________________________________________________________ Programming Procedures (Continued) 3 Press the corresponding CO/PBX line key and dial pad keys to change the data Default Values option: Key No. Data Setting Functions can be assigned to keys 01~60 on Attendant Add-On Consoles 1~4. Functions to be programmed: TEL No.
Page 234
Elite IPK Document Revision 1 ___________________________________________________________________________________ Programming Procedures (Continued) 4 Press to write the data. 5 Repeat Steps 3 and 4 for all buttons for each DSS. The next Memory Block is displayed. 6 Program the next Memory Block or press to go back on-line.
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-6-07 Message Board Lamp Assignment System Mode General Description Submode Use this Memory Block to assign mailbox numbers for each Message Display Board. Display Data No. L a m p S e t t i n g B o a r d D a t a S e t t i n g...
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-6-08 Attendant Transfer Selection During System Mode Live Record Submode General Description Use this Memory Block to control the Attendant DSS/BLF transfer while the Attendant Data No. is engaged in Live Record. The call is transferred to either the DSS/BLF extension or the voice mailbox of the DSS/BLF extension.
Page 237
Document Revison 1 Elite IPK ___________________________________________________________________________________ THIS PAGE INTENTIONALLY LEFT BLANK ___________________________________________________________________________________ 2 - 166 Memory Blocks...
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-7-00 Doorphone Assignment System Mode General Description Submode Use this Memory Block to enable the doorphones in System Programming. Display Data No. D a t a T i t l e N o . PC Programming +BTP 0 0 : D P H...
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-7-01 Doorphone Display Time Selection System Mode General Description Submode Use this Memory Block to specify the time, in seconds, a doorphone call signals a station before it times out. Data No. Display S e t t i n g D a t a PC Programming T i t l e...
Page 240
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-7-02 External Speaker Connection System Mode Selection Submode General Description Use this Memory Block to specify whether or not external speakers are connected to Data No. the system. Display PC Programming D a t a N o .
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-7-03 External Paging Alert Tone Selection System Mode General Description Submode Use this Memory Block to specify whether or not a paging alert tone is sent on External Zone Paging (all speakers/individual speaker). Data No. Display S e t t i n g D a t a...
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-7-04 Doorphone Ring Pattern Selection System Mode General Description Submode Use this Memory Block to turn doorphone Off/On or specify the doorphone ring pattern. Doorphones can be individually assigned. Data No. Display S e t t i n g D a t a PC Programming T i t l e...
Page 243
Document Revison 1 Elite IPK ___________________________________________________________________________________ The Doorphone Ring Patterns are shown in the table below: s= seconds Line Pattern Tone LK 1 Tone LK 2 LK 3 LK 4 LK 5 LK 6 LK 7 LK 8 LK 1 (Pg.
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-7-05 Doorphone Ringing Frequency System Mode Selection Submode General Description Use this Memory Block to specify the doorphone ringing frequency. Doorphones can Data No. be individually assigned. Display PC Programming +BTP S e t t i n g D a t a D a t a T i t l e...
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-7-06 External Paging Timeout Selection System Mode General Description Submode Use this Memory Block to specify the time allowed for External Paging before timeout and release of the paging circuit. Data No. Display S e t t i n g PC Programming D a t a D a t a...
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-7-07 External Ring Relay Pattern Selection System Mode General Description Submode Use this Memory Block to assign a distinctive ringing control/interval pattern to relay circuits. Data No. Display E x t PC Programming R i n g D a t a R e l a y S e t t i n g...
Document Revison 1 Elite IPK ___________________________________________________________________________________ 1-7-08 External Speaker Chime Selection System Mode General Description Submode Use this Memory Block to specify whether a normal paging alert tone (4 tones) sounds before the speech path is established, a chime sounds at the start of the call, or a chime sounds at the start and end of the call.
Elite IPK Document Revision 1 ___________________________________________________________________________________ 1-7-09 External Speaker Chime Start Time System Mode Selection Submode General Description Use this Memory Block only when paging alert tone (four tones) is assigned in Data No. Memory Block 1-7-08 (External Speaker Chime Selection). This Memory Block specifies the delay time (in milliseconds) after an external paging code is dialed before the paging alert tone is provided.
Page 251
Document Revison 1 Elite IPK ___________________________________________________________________________________ THIS PAGE INTENTIONALLY LEFT BLANK ________________