Siemens SINAMICS G150 Manual page 1126

[2819.8] SS2 active
[2855.6]<3>
r9722.2
[2858.6]<2>
SS1 active
[2819.8]
r9722.1
[2855.6]<3>
[2858.6]<2>
Deselect STO
[2855.3]<3>
r9720.0
[2858.3]<2>
R Q
Deselect SS1
<4>
[2855.3]<3>
1
r9720.1 S Q
[2858.3]<2>
STOP A or STOP B or STO or SS1 active
r9721.12
SI Mtn t F->B CU
0.00...600000.00 [ms]
p9555 (0.00)
STOP F and then STOP B actively
T 0
r9723.1
SI Mtn t F->B MM
0.00...600000000.00 [μs]
STOP D active
p9355 (0.00)
r9721.14
Deselect SOS
[2855.3]<3>
1
r9720.3
[2858.3]<2>
R Q
Deselect SS2
<4>
[2855.3]<3>
1
r9720.2 S Q
[2858.3]<2>
STOP C or SS2 active
r9721.13
<1> Only for p9601.2 = 1 and p9801.2 = 1.
<2> Only at drive via PROFIsafe.
<3> Only at drive via TM54F or onboard interface for CU310-2.
<4> With a simultaneous 1-signal at the R and S inputs, the S input dominates.
1 2
DO: SERVO, VECTOR
SI Extended Functions - SS1, SS2, SOS, internal STOP B, C, D, F
Safe Acceleration Monitor (SAM) /
Safe Brake Ramp (SBR) exceeded
r9714[0]
SI Mtn IL t_Ver CU
0.00...600000.00 [ms]
p9556 (100.00)
T 0
STOP B
SI Mtn IL t_Ver MM
0.00...600000000.00 [μs]
p9356 (100000.00)
SI Mtn t D->SOS CU
0.00...600000.00 [ms]
p9553 (100.00)
T 0
SI Mtn t D->SOS MM
0.00...600000000.00 [μs]
p9353 (100000.00)
SI Mtn t C->SOS CU
0.00...600000.00 [ms]
p9552 (100.00)
T 0
SI Mtn t C->SOS MM
0.00...600000000.00 [μs]
p9352 (100000.00)
3 4
&
Actual value speed < p9360/p9560
STOP A
p9526 = 1
p9526 = 2
&
r0487[1].14
p9526 = 3
&
r0487[2].14
r0487[0].14
SI Mtn SLS t CU
0.00...600000.00 [ms]
p9551 (100.00)
T 0
SI Mtn SLS t MM
0.00...600000000.00 [μs]
p9351 (100000.00)
SAM: Safe Acceleration Monitor
SBR: Safe Brake Ramp
SLS: Safely-Limited Speed
SOS: Safe Operating Stop
SS1: Safe Stop 1
SS2: Safe Stop 2
5 6
fp_2819_54_eng.vsd
04.11.13 V04.07.00
p9500 (12000 μs)
<1>
STO active
[2855.6]<3>
r9722.0
[2858.6]<2>
[2804.1]
STO initiate
[2804.4]
[2810.4]
STO cause actual value is missing
[2804.1]
SS1 active
[2819.1]
r9722.1 [2855.6]<3>
[2858.6]<2>
SOS active
[2855.6]<3>
r9722.3
[2858.6]<2>
SS2 active
[2819.1]
r9722.2
[2855.6]<3>
[2858.6]<2>
7 8
Function diagram
- 2819 -
S120/S150/G130/G150