Siemens SINAMICS G150 Manual page 1209

Mot temp_sensor
p0600[M]
from mot temp module 1
0
[8017.8]
from encoder 1
1
[4704.8]
from encoder 2
2
[4704.8]
von Geber 3
3
[4704.8]
from Motor Modules 11
or CUA31
Mot Temperatur [°C]
p0603
10
[9576.7] (0)
e.g. r4105 from TM31
Mot temperatur [°C]
20
p0608[0...3]
(0)
e.g. r4105 from TM120
Mot temperatur [°C]
21
p0609[0...3]
(0)
e.g. r4105 from TM120
only for KTY
[8017.1]
<1> For KTY, PT100, PT1000 and PTC, the value p0606 = 0 has a different meaning:
KTY, PT100, PT1000: 0 The output of the timer is always switched out (logical 0)
PTC: 0 Delay time = 0 s
<2> The switch-in delay p0607 = 0 suppresses fault F07016.
<3> For KTY, PT100, PT1000 and "No sensor", temperature as defined in the model.
<4> Applies only for VECTOR.
<5> p0606 does not work for alarms via p0616.
<6> p0601 = 5 can only be evaluated if r0192.15 = 1 and p0600 = 11; PT100 is calibrated via p0624.
<7> The assignment of temperature channels 1 … 4 depends on the hardware used.
<8> The relevant rated response temperature (°C) depends on the temperature sensor chosen by the motor manufacturer.
1 2
DO: SERVO, VECTOR
Signals and monitoring functions - Thermal monitoring, motor
MAX
1
Mot_temp_sens type
<7>
p0601[M]
Mot Temp_sensortyp
r4620[0] r4620[1] r4620[2]
Temperature channel
0 = No sensor
Temp_sens type
1 = PTC alarm and
1 2
3
time
p4600[E] p4601[E] p4602[E]
2 = KTY84
Mot Temp_sensortyp
r4620[0] r4620[1] r4620[2]
3 = KTY84 & PTC,
Temperature channel
for encoder only
Temp sens type MDS
4 = Bimetal NC
contact alarm
1 2
with time step p4610[M] p4611[M] p4612[M]
for MM only
Configuration
5 = PT100 <6>
0 = No sensor
10 = Evaluation
10 = PTC fault
across several
temperature
11 = PTC alarm
channels
12 = PTC alarm and time step
SME12x
20 = KTY, PT100, PT1000
11 = Evaluation
30 = Bimetal NC contact fault
across several
temperature
31 = Bimetal NC contact alarm
channels BICO
32 = Bimetal NC contact
alarm & time step
3 4
Mot_temp
1
r0035
Mod 1/2 threshold
p0605[M]
1
0
r4620[3]
KTY sensor type
(threshold not applicable for PTC)
Mod 2/KTY A thresh
4 p0604[M]
Mot temp alarm 1
p4603[E]
r4620[3]
M I N
1650
3 4
p4613[M]
KTY PTC
Sensor type
<3>
-140 °C 250 °C
5
fp_8016_54_eng.vsd
28.01.14 V04.07.00
Mot temp response
p0610[M]
<4>
&
Fault response
I_max reduction
&
[6300.1], [6640.2]
p0616[M]
Mod 2/KTY t_timer
p0606[M]
<8>
<1> <5>
T 0
F07011
&
1 "Motor overtemperature"
[8017.8]
1
r2135.12
[8017.8]
1
A07910
"Motor overtemperature"
0
Sensor fault time
1
r2135.14
p0607[M]
<2>
A07016
T 0
"Motor temperature
sensor fault, fault"
A07015
"Motor temperature
sensor fault alarm"
A07820 "Temperature sensor not connected"
6 7
Function diagram
S120/S150/G130/G150
48 ms
p0610 = 1
Suppress fault
at p0610 = 0
[2548.2]
[2548.2]
8
- 8016 -