Table of Contents
Advertisement
Command
ATS2=<n>
n=0-126
[&F]
n=127
ATS3=<n>
[&F]
n=13
ATS4=<n>
[&F]
n=10
ATS5=<n>
[&F]
n=8
ATS6=<n>
[&F]
n=2-10
ATS8=<n>
[&F]
n=1-255
ATS10=<n>
[&F][&W]
n=1-255
ATS30=<n>
n=0
[&F]
n=1-255
ATS103=<n>
n=0
n=1
[&F]
n=2
ATS104=<n>
n=0
n=1
[&F]
n=2
ATV<n>
n=0
[&F][&W]
n=1
ATX<n>
n=0
n=1
n=2
n=3
[&F][&W]
n=4
ATZ
+++
Outline/Parameter
Sets an escape character.
43: Default, 0: When the parameter is omitted
Disables the escape operation.
Sets a carriage return (CR) character that can identify the end of an
AT command character string. It is added to the end of the echoed
back command character string and result code.
Default
Sets a line feed (LF) character. When the result code is displayed in
alphabets, it is added after the carriage return (CR) character.
Default
Sets a backspace (BS) character that deletes the last character of
input buffer during AT command input.
Default
Sets the pause time (seconds) until dialing. Although the register
is set, the operation does not take place even if this command is
used.
5: Default, when the parameter is omitted
Sets the pause time (seconds) until a comma dial is performed.
Although the register is set, the pause time is fixed to 3 seconds
even if this command is used.
60: Default, 121-255: Assumes 120
Sets the automatic disconnection delay time (1/10 seconds).
Although the register is set, the operation does not take place even
if this command is used.
1: Default, when the parameter is omitted
Sets the waiting time (minutes) until communication is disconnected
when no data is exchanged during 64K data communication.
Does not disconnect (Default, when the parameter is omitted).
Waiting time (minutes) until communication is disconnected
Sets a separator used when originating a call by adding an
incoming call sub-address for 64K data communication.
(When the parameter is omitted)
/ (Default)
¥
Sets a separator used when originating a call by adding an
outgoing call sub-address for 64K data communication.
# (When the parameter is omitted)
% (Default)
&
Sets the display method for the result code.
Displays the result code using a numeric value (When the
parameter is omitted).
Displays the result code using text (Default).
Sets the busy tone and dial tone detection, and communication
speed indication.
Without busy/dial tone detection, without speed indication (When
the parameter is omitted)
Without busy/dial tone detection, with speed indication
Without busy tone detection, with dial tone detection, without speed
indication
With busy tone detection, without dial tone detection, with speed
indication
With busy/dial tone detection, with speed indication (Default)
Sets the FOMA terminal settings to the contents of a volatile
memory recorded by AT&W. When this command is executed
during communication, the operation for disconnecting the line is
performed.
Switches the FOMA terminal from the online data mode to the online
command mode. The escape guard section is fixed to 1 second.
27
Input example
ATS2=0
ATS2?
ATS3=13
ATS3?
ATS4=10
ATS4?
ATS5=8
ATS5?
ATS6=5
ATS6?
ATS8=3
ATS8?
ATS10=1
ATS10?
ATS30=0
ATS30?
ATS103=0
ATS103?
ATS104=0
ATS104?
ATV1
ATX1
ATZ
+++
Advertisement
Chapters
Table of Contents
