Switchnet Data I/O Port (As-Interface Master Module 1) - IDEC FC4A-C10R2 User Manual

SwitchNet Data I/O Port
SwitchNet control units can be used as slaves in the AS-Interface network and are available in ø16mm L6 series and
ø22mm HW series. Input signals to the
each input point designated by a slave number and a DI number. Similarly, output signals from the
face master module are written to internal relays allocated to each output point designated by a slave number and a DO
number. When programming a ladder diagram for the
signals of SwitchNet control units.
L6 series and HW series SwitchNet control units have slightly different digital I/O data allocations.
L6 Series Digital I/O Data Allocation
Input data is sent from slaves to the AS-Interface master. Output data is sent from the AS-Interface master to slaves.
SwitchNet L6 Series
Slave Unit
Pushbutton
Pilot light
Illuminated pushbutton
Selector, Key selector, Lever: 2-position
Selector, Key selector, Lever: 3-position
Illuminated selector: 2-position
Illuminated selector: 3-position
Notes:
1. ∗ The AS-Interface master uses bit DO3 for addressing A/B
slaves.
2. In the above table, bits marked with X1, X2, and X3 are used
for SwitchNet I/O data.
3. X1: When pushbutton is pressed, input data is 1 (on). When
not pressed, input data is 0 (off). When output data is 1 (on),
LED is on. When output data is 0 (off), LED is off.
4. X2: The input data from 2-position selector, key selector, and
illuminated selector switches and 2-position lever switches
depend on the operator position as shown below.
2-position Operator
Operator Position
DI2
•
Write_Parameter Command
0 0 A4 A3 A2 A1
MicroSmart
Selector Lever
Left Right
Left/Down Right/Up
0
Sel
A0 1 P2 P1 P0
P3
« FC4A M
28: AS-I
AS-Interface master module are read to internal relays allocated to
, use internal relays allocated to input signals and output
MicroSmart
Input Data
(slave send data)
Used I/O
DI3 DI2
1 in 0 X1
1 out 0 0
1 in/1 out 0 X1
1 in 0 X2
2 in X3 X3
1 in/1 out 0 X2
2 in/1 out X3 X3
5. X3: The input data from 3-position selector, key selector, and
illuminated selector switches and 3-position lever switches
depend on the operator position as shown below.
3-position Operator
Operator Position
Up
6. Unused input bits DI3 and DI2 are 0 (off), and unused input
bits DI1 and DI0 are 1 (on). Slaves ignore unused output data
(—) sent from the master.
Down
1
•
Write_Parameter Settings
PB 1
LED
Brightness
100%
50%
25%
12.5%
S U ' M
ICRO MART SER S ANUAL
M
NTERFACE ASTER
DI1 DI0 DO3
1 1 *
1 1 *
1 1 *
1 1 *
1 1 *
1 1 *
1 1 *
Selector
Center
Right
Left
Left/Down
DI3 0
DI2 1
Settings
Output
Control Data
Selection
P2 P1
1
0
1: DO0
0: DO1
1
0
»
C
OMMUNICATION
AS-Inter-
MicroSmart
Output Data
(slave receive data)
DO2 DO1 DO0
— — —
— — X1
— — X1
— — —
— — —
— — X1
— — X1
Lever
Up
Center
Down
Center Right/Up
0 1
0 0
Remarks
P0
1 Default
1
0
0
28-35