Page 1
A system should require only simple measures which can be performed without much thinking—such as pressing a pushbutton! Spring loaded actuator When the actuator is fully inserted (door closed completely), the door can tolerate a space of up to 16mm. For more information, visit http://asia.idec.com E-063...
Page 2
HS1L solenoid Spring loaded actuator Actuators for HS1/HS5/HS6 For sliding doors Actuators/ • Actuator for HS5L only. Cannot be used on HS9Z-BA5 Locks the door safely Padlock Hasp hinged doors. when the door bounces Download catalogs and CAD from http://asia.idec.com/downloads E-064...
Page 3
Padlock Hasp (Angle Adjustable) (vertical/horizontal) 2-M4 Screw Note: The actuator stop film and actuator stop are supplied with the actuator and used when adjusting the actuator position. Remove after the actuator position is determined. For more information, visit http://asia.idec.com E-065...
Page 4
As shown in the figure on the right, the mounting reference position of the actuator when inserted in the interlock switch is the position where the actuator stop placed on the actuator lightly touches the side surface of the interlock switch. Note: After mounting the actuator, remove the actuator stop from the actuator. Download catalogs and CAD from http://asia.idec.com/downloads E-066...
Page 6
Remove them Actuators for after the actuator position is determined. (45.1) HS1/HS5/HS6 42.6 Actuators/ 20.5 Padlock Hasp 11.5 11.5 2-M5 Screws Actuator Cover When (gray) (Note) mounted (8) Download catalogs and CAD from http://asia.idec.com/downloads E-068...
Page 7
*1) Select actuator by determining the required moving direction in consideration of the door and interlock switch. Interlock Switches Non-contact Interlock Switches Safety Laser Scanners Safety Light Curtains Safety Modules HS6B HS6E HS5D HS5L HS1L Actuators for HS1/HS5/HS6 Actuators/ Padlock Hasp For more information, visit http://asia.idec.com E-069...
Page 8
(ø4.3 or M4 tapped) Non-contact Angle Adjustable Actuator Interlock Switches Safety Laser Scanners Safety Light 2-M4 Screws Curtains (ø4.3 or M4 tapped) Safety Modules HS6B HS6E HS5D HS5L HS1L Actuators for HS1/HS5/HS6 Actuators/ Padlock Hasp Download catalogs and CAD from http://asia.idec.com/downloads E-070...
HS5E-L Rear Handle Hole ø26 to 30 (∗1) HS5E-KL HS5L-L Rear Unlocking Button Hole 151.6mm 147.2mm 4(6)-M5 ø22 to 30 (∗2) Door Gap Door Gap All dimensions in mm. <Front View> <Rear View> For more information, visit http://asia.idec.com E-075...
Page 14
Safety Light Note: The illustration kit contains the aluminum mounting Curtains plate shown above and two spacers. Safety Modules All dimensions in mm. HS6B HS6E HS5D HS5L HS1L Actuators for HS1/HS5/HS6 Actuators/ Padlock Hasp Download catalogs and CAD from http://asia.idec.com/downloads E-076...
Page 15
Screw A and two otherwise the actuator will hit the door, resulting in deformation or Screws B. damage. Screws B • When turning the handle, make sure that your hands or fingers are not caught by the door. For more information, visit http://asia.idec.com E-077...
Page 16
Shaft turn the button operating pin to the horizontal position. Rear Handle Plate Connecting Rod Connecting Rod Orientation 6. Install the rear handle (gunmetal color) on the rear handle shaft. Correct Incorrect Pull Download catalogs and CAD from http://asia.idec.com/downloads E-078...
Page 17
When other screws are used and Actuators for tightened to a smaller torque, make sure that the screws do not become HS1/HS5/HS6 loose after mounting. Actuators/ Padlock Hasp For more information, visit http://asia.idec.com E-079...
Page 18
Part (sold separately) HS6E HS5D HS5L Bolt HS1L Rear Lever Handle (black) Actuators for (black) Rear Unlocking HS1/HS5/HS6 Padlockable Actuator Button Actuators/ Hole Padlock Hasp Interlock Switch (sold separately) Rear View Front View Download catalogs and CAD from http://asia.idec.com/downloads E-080...
Page 19
Switches & Pilot Lights HS9Z-FL54 30 ≤ Y ≤ 35 Control Boxes HS9Z-FL55 35 < Y ≤ 45 Emergency • Contact IDEC for mounting part thicker than specified above. Stop Switches Material: Enabling Material: ST37 PA6 (black) Switches zinc coated M6 screws...
Page 20
• The applicable shackle diameter is ø6 to 13. 2. Fasten the switch base unit on the mounting frame or panel. Mounting screws and nuts are not supplied and must be provided by the user. Applicable shackle diameter: ø6 to 13mm Download catalogs and CAD from http://asia.idec.com/downloads E-082...
Page 21
Rear Lever (M6) Actuators for HS1/HS5/HS6 Actuators/ Padlock Hasp Handle Unit • Apply Loctite to the screw so that it does loosen. • Mounting screws and nuts are not supplied and must be provided by the user. For more information, visit http://asia.idec.com E-083...
Page 22
Power Supplies LED Illumination Controllers Operator Interfaces Sensors AUTO-ID Interlock Switches Non-contact Interlock Switches Safety Laser Scanners Safety Light Curtains Safety Modules HS6B HS6E HS5D HS5L HS1L Actuators for HS1/HS5/HS6 Actuators/ Padlock Hasp Download catalogs and CAD from http://asia.idec.com/downloads E-084...
Page 23
Scanners 26.5 Safety Light 37.5 Curtains 6-M5 Screws 32.5 Safety Modules (40) HS6B 30.7 HS6E All dimensions in mm. HS5D Actuator (SUS) HS5L Thickness: 2.5 Cover (SUS) HS1L Actuators for HS1/HS5/HS6 Actuators/ Padlock Hasp For more information, visit http://asia.idec.com E-085...
• Do not close the door when the actuator is slid out of the cover, otherwise the actuator may damaged. • When using the sliding actuator, take care so that fingers or hands are not caught between the actuator and interlock switch. Download catalogs and CAD from http://asia.idec.com/downloads E-086...
Page 25
61.5 Thickness: 2.5 30.5 Area Coating: Orange 10.5 HS6B HS6E HS5D HS5L 15.5 HS1L Actuators for HS5D HS5L Interlock Switch Interlock Switch HS1/HS5/HS6 (30) (30) (35) (40) Actuators/ Padlock Hasp All dimensions in mm. For more information, visit http://asia.idec.com E-087...
• When an operator enters the danger zone, take measures such as Padlock Hasp and the machine can not be started by mistake. using a Padlock Hasp (HS9Z-PH5) so that the operator is not trapped, and the machine can not be started by mistake. Download catalogs and CAD from http://asia.idec.com/downloads E-088...
Page 27
HS6B Rivet: HS6E Stainless Steel 38.5 33.5 Material: SPCC HS5D Thickness: 2.0 HS5L HS5D Interlock Switch (30) (30) HS1L HS5L Actuators for Interlock Switch HS1/HS5/HS6 (35) (40) Actuators/ Padlock Hasp All dimensions in mm. For more information, visit http://asia.idec.com E-089...