Mitsubishi Electric MELSEC-Q QD75M User Manual page 853

Simultaneous starting axis start data No. (Axis 3
Cd.32
start data No.)(
Simultaneous starting axis start data No. (Axis 4
Cd.33
start data No.)(
Cd.37
Skip command (
Skip function ................................................ 12-61
Skip operation program................................. 6-47
Slot................................................................... 2-6
Software stroke limit function...................... 12-29
Software stroke limit lower limit value (
....................................................................... 5-28
Software stroke limit selection (
Software stroke limit upper limit value (
....................................................................... 5-28
Software stroke limit valid/invalid setting (
....................................................................... 5-28
S-pattern acceleration/deceleration processing
method......................................................... 12-82
S-pattern proportion (
Special start instruction (
Special start data instruction code setting value
Md.36
( )...................................................... 5-130
Special start data instruction parameter setting
Md.37
value ( )............................................ 5-130
Special start repetition counter (
Specifications of input/output interfaces....... 3-18
Specifications of input/output signals ........... 3-14
Speed change 0 flag ................................... 5-126
Speed change function ............................... 12-37
Speed change program ................................ 6-43
Speed change request (
Speed designation during OP shift (
....................................................................... 5-56
Speed differential compensation (
Speed integral compensation (
Speed integral compensation changing ratio
( ) ........................................................ 5-80
Pr.155
Speed limit function..................................... 12-23
Pr.8
Speed limit value (
Stop command processing for deceleration
stop selection (
Cd.42
Speed loop gain 1 (
Pr.114
Speed loop gain 2 (
Pr.116
Speed loop gain changing ratio (
Speed-position function selection (
) .............................. 5-156
) .............................. 5-156
) ............................ 5-158
Pr.13
Pr.14
) ..... 5-28
Pr.12
Pr.15
Pr.35
)...................... 5-38
Da.13
) .............. 5-101
Md.41
)... 5-132
Cd.15
) ............... 5-107
Pr.56
)
) .. 5-76
Pr.138
) ....... 5-64
Pr.117
) ............................ 5-26
)............................... 5-138
) ......................... 5-64
) ......................... 5-64
).... 5-78
Pr.154
). 5-32
Pr.200
Speed switching mode (
Speed-position switching control (ABS mode)
........................................................................9-91
Speed-position switching control (INC mode)
........................................................................9-86
Speed-position switching control movement
amount change register (
Speed-position switching control positioning
Md.29
amount (
)
Speed-position switching enable flag (
......................................................................5-152
Speed-position switching latch flag .............5-126
)
Speed-position switching signal ....................3-18
Spiral interpolation .........................................9-61
)
SSCNET........................................................ A-14
SSCNET cable over all length.........................3-3
Standard speed switching mode ...................9-12
Start Hour (
Start complete signal .....................................3-15
Start data No. (
Start data pointer being executed (
......................................................................5-132
Start details setting program..........................6-54
Start history ..................................................5-112
Start history pointer (
Start information (
Start Minute: second (
Start No. (
Start positioning data No. setting value
Md.38
( ) ......................................................5-130
Start program .................................................6-56
Start program for high-level positioning control
......................................................................10-23
Md.31
Status (
Step function ................................................12-56
Step mode....................................................12-57
Step mode (
Step operation program.................................6-46
Step start information...................................12-58
Step start information (
Index - 8
Pr.19
)..................5-32
Cd.23
).........................................5-124
Md.5
) ......................................5-112
Da.12
) ..............................5-101
Md.8
) .......................5-114
Md.3
) ............................5-112
Md.6
) .....................5-112
Md.4
).........................................5-112
)...........................................5-126
Cd.34
) ...................................5-156
Cd.36
) ..................5-158
) ..............5-152
Cd.24
)
Md.43
)