Mitsubishi Electric MELSEC-Q QD75M User Manual page 849

Input signal logic selection (
Interface internal circuit ................................. 3-21
Intentional stop .............................................. 6-70
Internal circuit ................................................ 3-21
Internal current consumption .......................... 3-3
Interpolation axis ........................................... 9-21
Interpolation control....................................... 9-21
Interpolation speed designation method (
....................................................................... 5-32
Interruption request during continuous operation
Cd.18
( )...................................................... 5-148
[J]
JOG operation ............................................... 11-4
JOG operation acceleration time selection
Pr.32
( )........................................................ 5-36
JOG operation deceleration time selection
Pr.33
( )........................................................ 5-36
JOG operation setting program .................... 6-41
JOG operation start time chart.................... 11-11
JOG operation timing and processing times
....................................................................... 11-6
Cd.17
JOG speed (
JOG speed limit value (
JOG start signal............................................. 3-14
JUMP instruction ......................................... 9-112
[K]
[L]
Last executed positioning data No. (
..................................................................... 5-132
LED display functions................................ 15-106
LEND ........................................................... 9-115
List of block start data ................................... 5-98
List of condition data ................................... 5-104
List of configuration devices............................ 2-4
List of control data ....................................... 5-138
List of dedicated instructions......................... 14-2
List of devices used......................................... 6-5
List of errors................................................... 15-6
List of functions................................................ 3-4
List of input signal details .............................. 3-20
List of input/output signals ............................ 3-14
List of monitor data...................................... 5-110
List of parameters.......................................... 5-22
List of positioning data .................................. 5-82
Pr.22
) ........... 5-32
Pr.20
).................................. 5-148
Pr.31
) .................. 5-36
Md.46
List of warnings ............................................15-90
Load inertia (
LOOP ...........................................................9-114
Lower limit ......................................................3-21
[M]
M code (Condition data No., No. of LOOP to
LEND repetitions) (
)
M code OFF request....................................12-65
M code OFF request (
M code ON signal ..........................................3-15
M code ON signal output timing ..................12-64
M code ON signal output timing (
M code output function ................................12-64
Machine feed value........................................9-16
Machine feed value (
Machine OPR...................................................8-4
Machine response suppression filter (
........................................................................5-66
Machine response suppression filter 2 (
........................................................................5-80
Main functions ..................................................3-6
Major positioning controls................................9-2
Manual control ...............................................11-2
Manual pulse generator...................................2-4
Manual pulse generator................................ A-14
Manual pulse generator cable ..........Appendix-36
Manual pulse generator 1 pulse input
magnification (
Manual pulse generator enable flag (
......................................................................5-150
)
Manual pulse generator input selection (
........................................................................5-32
Manual pulse generator operation ..............11-27
Manual pulse generator operation program
........................................................................6-42
Manual pulse generator operation start time chart
......................................................................11-34
Manual pulse generator operation timing and
processing times ..........................................11-29
Mechanism of positioning control....................1-7
Monitor data area.............................................7-3
Movement amount after near-point dog ON
Md.34
(
Monitor output 1 offset (
Monitor output 2 offset (
Motor capacity (
Index - 4
) ....................................5-64
Pr.112
Da.10
)..........................5-94
Cd.7
) .....................5-140
Md.21
) .....................5-120
Cd.20
) ...............................5-150
) ......................................................5-128
Pr.127
Pr.128
) ..............................5-60
Pr.104
Pr.18
) ...5-30
)
Pr.118
)
Pr.161
Cd.21
)
Pr.24
)
) ..................5-74
) ..................5-74