Index - Mitsubishi Electric MELSEC-Q QD75M User Manual

INDEX

[Number]
1-axis fixed-feed control ................................ 9-44
1-axis linear control (ABS linear 1) ............... 9-27
1-axis linear control (INC linear 1) ................ 9-28
1-axis speed control ...................................... 9-68
2-axis circular interpolation control with sub point
designation (ABS circular sub)
....................................................................... 9-54
2-axis circular interpolation control with sub point
designation (INC circular sub)
....................................................................... 9-57
2-axis circular interpolation control with center
point designation (ABS circular right/ABS circular
left) ................................................................. 9-62
2-axis circular interpolation control with center
point designation (INC circular right/INC circular
left) ................................................................. 9-65
2-axis fixed-feed control (interpolation)
....................................................................... 9-46
2-axis linear interpolation control (ABS linear 2)
....................................................................... 9-29
2-axis linear interpolation control (INC linear 2)
....................................................................... 9-31
2-axis speed control ...................................... 9-71
3-axis fixed-feed control (interpolation)
....................................................................... 9-48
3-axis linear interpolation control (ABS linear 3)
....................................................................... 9-33
3-axis linear interpolation control (INC linear 3)
....................................................................... 9-36
3-axis speed control ...................................... 9-74
4-axis fixed-feed control (interpolation)
....................................................................... 9-52
4-axis linear interpolation control (ABS linear 4)
....................................................................... 9-39
4-axis linear interpolation control (INC linear 4)
....................................................................... 9-42
4-axis speed control ...................................... 9-78
[A]
ABS direction in degrees (
Absolute system ............................................ 9-15
Acceleration time 0 (
Acceleration time 1 (
Cd.40
)............ 5-158
Pr.9
) ......................... 5-26
Pr.25
) ....................... 5-36
Acceleration time 2 (
Acceleration time 3 (
Acceleration time No. (
Acceleration/deceleration process selection
Pr.34
( ) ........................................................5-38
Acceleration/deceleration processing function
......................................................................12-81
Acceleration/deceleration time change during
speed change, enable/disable selection (
......................................................................5-144
Acceleration/deceleration time change function
......................................................................12-47
Acceleration/deceleration time change program
........................................................................6-45
Actual acceleration/deceleration time ...........5-26
Adaptive vibration suppression control/low pass
Pr.125
filter (
Da.17
Address (
AFTER mode ...............................................12-65
Allowable circular interpolation error width
Pr.41
( ) ........................................................5-42
Amplifier setting (
Analog monitor output (
Applicable system ............................................2-6
Applicable wire size .........................................3-3
Arc address (
Auto tuning (
Automatic trapezoidal acceleration/deceleration
processing method ......................................12-82
Axis display LED ..............................................4-3
Axis error No. (
Axis error occurrence (Hour) (
Axis error occurrence (Minute: second) (
......................................................................5-116
Axis error reset (
Axis feed rate (
Axis in which the error occurred (
......................................................................5-116
Axis in which the warning occurred (
......................................................................5-118
Axis monitor data .........................................5-120
Index - 1
Pr.26
)........................5-36
Pr.27
)........................5-36
Da.3
)......................5-84
).................................................5-72
) .......................................5-107
) .............................5-58
Pr.101
) ...................5-68
Pr.122
Da.7
) .....................................5-92
).....................................5-62
Pr.108
Md.10 Md.23
, ).........5-116, 120
Md.11
Cd.5
) ..............................5-140
Md.28
) ..............................5-124
Md.9
Cd.12
)
) ......5-116
Md.12
)
)
Md.14
)