Download Print this page

Electrolux EXP26U338CW User Manual page 15

Hide thumbs

Advertisement

Table of Contents
Fan mode
In this mode, there is no need to use the
exhaust hose or drainage hose.
1. Press the "mode" button until
the Fan mode indicator is lit.
2. Press the "Fan speed" button
to choose the desired fan speed.
3. The fan will run at the selected speed
and the display will show the room
temperature.
Note: In this mode, auto speed cannot
be selected.
Auto mode
Always have the exhaust hose attached
in this mode.
When you set the air conditioner in Auto
mode, it will automatically select cooling,
heating (inapplicable for cooling only
models), or fan only operation depending
on what temperature you have selected and
the room temperature. The air conditioner
will control room temperature automatically
round the temperature point set by you.
Under AUTO mode, you can not select
the fan speed.
1. Press the "mode" button until the
"Auto mode" indicator lights.
After the "Auto mode" is selected the unit
will run automatically according to the
actual room air temperature.
Timer mode
The timer facilitates the user to delay the
unit startup or shutdown.
How to delay startup
Plug in the unit, so the unit turns to standby.
Press the "timer" button, then the Timer
indicator will switch on and the number
of hours on the screen will show "0.0".
Tap or hold the UP arrow " " or the DOWN
arrow " " to change delay start timer at
0.5 hour increments up to 10 hours, then
at 1 hour increments up to 24 hours. Press
the "timer" button again within 5 seconds,
you will quit the timer setting directly.
After 5 seconds, the timer function
is enabled, the display will show the
temperature back. The control will count
down the time remaining until startup.
The unit will start up in the mode
as previously set.
To cancel the setting, press the "timer"
button again will show the remain time and
press the button again to quit the function.
You can also cancel the setting by pressing
the "on/off" button. After cancel the setting,
the timer indicator will switch off.
How to delay shutdown
You can delay shutdown when the unit
is on.
Press the "timer" button, then the Timer
indicator will switch on and the number
of hours on the screen will show "0.0".
Tap or hold the UP arrow " " or the
DOWN arrow " " to change delay
stop timer at 0.5 hour increments up
to 10 hours, then at 1 hour increments
up to 24 hours. Press the "timer" button
again within 5 seconds, you will quit
the timer setting directly.
After 5 seconds, the timer function
is enabled, the display will show the
temperature back. The control will count
down the time remaining until shuts down.
To cancel the setting, press the "timer"
button again will show the remaing time and
press the button again to quit the function.
You can also cancel the setting by pressing
the "on/off" button. After cancel the setting,
the timer indicator will switch off.
Sleep mode
Active this feature will give you a
comfortable temperature and help
save energy.
Only when the unit is in Cool, Heat or auto
mode, you can press the "sleep" button to
make the unit run in Sleep mode.
Note: Please refer to page 17 for the
details about "Sleep" mode.
Louver Swing Function
Press the "swing" button to enable louver
swing function, the louver on the top
panel will swing up and down.
Press this button again to disable the
louver swing function.
°F/°C function
Press the " " and " " button the same
time for more than 3 seconds to switch
between degree Fahrenheit and degrees
Celsius. Under Dry/Fan mode, you can
not select °F/°C.
Filter reset
This feature is a reminder to clean the Air
Filter (See Care and Cleaning) for more
efficient operation.
The filter indicator will illuminate after
250 hours of operation. To reset after
cleaning the filter, press the "filter reset"
button, then the "filter" indicator will go off.
ENGLISH
15

Hide quick links:

Advertisement

Table of Contents
loading