Vision VR48 4 Series User Manual page 88

88 Vision VR48 Series 4 Router User Manual
Enter are toggles. To return to the main Pendant screen, press the Exit button two times.
Dry Run Speed - Pressing Enter with this item highlighted will allow the user to set the dry run XY
speed of the motion system. To set the speed, use the Y up or down buttons to highlight the menu item
and press Enter. Use the numeric buttons to enter the desired speed, then press Enter to save this
speed. To return to the main Pendant screen, press the Exit button two times.
Outline Speed - Pressing Enter with this item highlighted will allow the user to set the outline speed
which used by the measure feature in the Vision Pro software. To set the speed, use the Y up or down
buttons to highlight the menu item and press Enter. Use the numeric buttons to enter the desired speed,
then press Enter to save this speed. To return to the main Pendant screen, press the Exit button two
times.
Select Interface - Pressing Enter with this item highlighted will allow the user to select HPGL or GCode
interface language. The Vision controller can run from both HPGL and GCode machine language. By
default the controller uses the HPGL language which is what is used by Vision and Vision Pro software.
If you would like to run GCode, move the cursor to the Select Interface menu item using the Y up and
down jog buttons and press Enter. Use the Y up or down buttons to select the language you would like to
use, then press Enter. Press the Exit button two times to return to the main screen when finished.
Parking - Pressing Enter with this item highlighted will allow the user to set the position the spindle will
return to after a job has finished. To set this position, move the cursor to the Parking menu item using
the Y up and down jog buttons and press Enter. There are four positions that you can set the spindle to
move to at the end of the job. Datum: The spindle will move back to the limit switch position on the table.
None: The spindle will remain at its last location when the job is finished. Z-Up: The spindle will remain at
its last location at the end of the file and lift the spindle off the material. Home: The spindle will move to
the current home position that is set in the controller. Use the Y up and down job buttons to select which
parking position you would like to use, then press Enter to select it. Press the Exit button two times to
return to the main screen when finished.
Set Dwell Up - This is used only with tables that are using an air actuated Z axis. None of the current
Vision systems use an air actuated Z axis. This will allow the Z axis to release the air pressure so that
the spindle moves up before moving to the next item to be engraved. Move the cursor to the Set Dwell Up
menu item using the Y up and down jog buttons and press Enter. Enter the length of time required for
the Z dwell up and then press Enter. This number is in milliseconds so entering a number of 1000 will
allow for a 1 second delay. Press the Exit button two times to return to the main screen when finished.
Input Units - Pressing Enter with this item highlighted will allow the user to set the units used by the
machine to either Imperial or Metric units. This differs from the Display Units menu item in that the input
units are what the machine recognizes from the job sent to the machine, while the display units simply
show the file on the Pendant screen as Imperial or Metric. The input units MUST match the units used to
create the job, or improper scaling of the job will result. To select the input units, use the Y up or down
buttons to highlight the menu item and press Enter. Use the Y up or down buttons to select either
Imperial or Metric units, then press Enter to save this setting. To return to the main Pendant screen,
press the Exit button two times.
Pointer Offset - Pressing Enter with this item highlighted will allow the user to modify the factory
settings used in the machine to compensate for the offset between the spindle centerline and the red dot
laser pointer location. Modification of this setting may be necessary if the location of the red dot laser
pointer does not accurately represent the location of the spindle during engraving. To modify this
setting, use the Y up or down buttons to highlight the menu item and press Enter. Use the numeric
buttons to enter the X offset, then press Enter. Use the numeric buttons to enter the Y offset, then press
Enter. The settings are now saved. To return to the main Pendant screen, press the Exit button two
times.
Braille Inserter - Pressing Enter with this item highlighted will toggle the Braille Inserter function to On
© 2015 Vision Engraving and Routing Systems