D-Link xStack DGS-3324SRi Command Line Interface Reference Manual page 228

Command
create access_profile
config access_profile
profile_id
create access_profile
config access_profile
profile_id
create access_profile
config access_profile
profile_id
Each command is listed, in detail, in the following sections.
create access_profile (for Ethernet)
Purpose
Syntax
xStack Gigabit Layer 3 Switch Command Line Interface Manual
Parameters
ip {vlan | source_ip_mask <netmask> | destination_ip_mask
<netmask> | dscp | [icmp {type | code} | igmp {type} | tcp
{src_port_mask <hex 0x0-0xffff> | dst_port_mask <hex 0x0-0xffff>
| flag_mask [all | {urg | ack | psh | rst | syn | fin}]} | udp
{src_port_mask <hex 0x0-0xffff> | dst_port_mask <hex 0x0-xffff>}
| protocol_id {user _mask <hex 0x0-0xffffffff> }]} profile_id <value
1-8>}
<value 1-8> [add access_id <value 1-100> ip {vlan <vlan_name
32> | source_ip <ipaddr> | destination_ip <ipaddr> | dscp <value
0-63> | [icmp {type <value 0-255> code <value 0-255>} | igmp
{type <value 0-255>} | tcp {src_port <value 0-65535> | dst_port
<value 0-65535> | urg | ack | psh | rst | syn | fin} | udp {src_port
<value 0-65535> | dst_port <value 0-65535>} | protocol_id <value
0 - 255> {user_define <hex 0x0-0xffffffff> }]} port <port> [permit
{priority <value 0-7> {replace_priority} | replace_dscp <value 0-
63>} | deny] delete <value 1-100>]
packet_content_mask {offset_0-15 <hex 0x0-0xffffffff> <hex 0x0-
0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> | offset_16-31
<hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex
0x0-0xffffffff> | offset_32-47 <hex 0x0-0xffffffff> <hex 0x0-0xffffffff>
<hex 0x0-0xffffffff> <hex 0x0-0xffffffff> | offset_48-63 <hex 0x0-
0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-
0xffffffff> | offset_64-79 <hex 0x0-0xffffffff> <hex 0x0-0xffffffff>
<hex 0x0-0xffffffff> <hex 0x0-0xffffffff>} profile_id <value 1-8>}
<value 1-8> [add access_id <value 1-100> packet_content
{offset_0-15 <hex0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-
0xffffffff> <hex 0x0-0xffffffff> | offset_16-31 <hex 0x0-0xffffffff>
<hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> |
offset_32-47 <hex 0x0-0xffffffff> <hex 0x0-0xffffffff><hex 0x0-
0xffffffff> <hex 0x0-0xffffffff> | offset_48-63 <hex 0x0-0xffffffff>
<hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> |
offset_64-79 <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-
0xffffffff> <hex0x0-0xffffffff>} port <port> [permit {priority <value 0-
7> {replace_priority} | replace_dscp <value 0-63>} | deny] delete
<value 1-100>]
ipv6 {class | flowlabel | source_ipv6_mask <ipv6mask> |
destination_ipv6_mask <ipv6mask>}] profile_id <value 1-8>}
<value 1-8> add access_id <value 1-100> ipv6 {class <value 0-
255> | flowlabel <hex 0x0-0xfffff> | source_ipv6 <ipv6addr> |
destionation_ipv6 <ipv6addr>} port <port> [permit {priority <value
0-7> {replace_priority}} | deny] | delete <value 1-100>]
Used to create an access profile on the Switch by examining the
Ethernet part of the packet header. Masks entered can be combined
with the values the Switch finds in the specified frame header fields.
Specific values for the rules are entered using the config
access_profile command, below.
create access_profile [ethernet {vlan | source_mac <macmask
000000000000-ffffffffffff> | destination_mac <macmask
000000000000-ffffffffffff> | 802.1p | ethernet_type} profile_id
220