Telephone Button Programming
300 Series Programs
Table 13-28
Programs 303~315 (continued)
Button
Sequence
304-19
Intercept
A7 (
Cyq
, n,
304-20
Send Dial Tone
A7
Cyq
, n,
304-21
TGAC Override
A7
Cyq
, n,
304-22
Network COS
A7
Cyq
, n,
304-23
LCR Group
A7 "
Cyq
, n,
304-24
Change COS
Override Code
A7 #
Cyq
, n,
304-25
Register Speed Dial
Codes
A7 $
Cyq
, n,
304-26
Originator Invoke
OCA
A7 %
Cyq
, n,
304-27
Senderized Tone
Mode
A7 &
Cyq
, n,
304-28
Emergency Call
Group
A7 &
Cyq
, n,
304-29
Tenant Number
A7 (
Cyq
, n,
305
ILG Delete
"$
Cyq
,
305-00
ILG Number
Cyq
Cyq
n,
,
Outgoing Line Group
306
Assignment
"%
Cyq
,
306-00
Group Number
Cyq
n,
306-01
Group Type
A7
Cyq
, n,
306-02
Trunk Type
A7
Cyq
, n,
13-58
Value(s)
n =
1. Enable
2. Disable (default)
n =
1. Enable
2. Disable (default)
n =
1. Enable
2. Disable (default)
n =
1~32
(default = 1)
n =
1~16
(default = 1)
n =
1. Enable
2. Disable (default)
n =
1. Enable
2. Disable (default)
n =
1. Enable
2. Disable (default)
n =
1. Dial Tone (default)
2. Entry Tone
3. Silence
n =
1~8
(default = 1)
Cyq
,
n =
1~8 (default = 1)
Cyq
,
n =
1~32 (CTX100)
1~50 (CTX670 Basic)
1~128 (CTX670 Exp.)
n =
1~32 (CTX100)
1~50 (CTX670 Basic)
1~128 (CTX670 Exp.)
n =
1. Analog (default)
2. ISDN
n =
1. CO (default)
2. Tie
Enable Intercept. A call is transferred to a special destination called
intercept position when the destination of a trunk line call is not
determined with DID, DIT or DISA. Intercept is also activated when
the destination is determined, but the call cannot be terminated due to
a defect or an incorrect number. If the system has a simplified
attendant console, the attendant console is usually specified to
terminate the call. This function ensures termination of a trunk line
call.
Enable Send Dial Tone.
Enable Trunk Group Access Code (TGAC) override.
Enter the Network COS number.
Enter the LCR Group number. Calls from this ILG cannot tandem if
this field is not entered.
Enable authority to change COS Override Code.
Enable authority to create system speed dial codes.
Enable authority for the originator of a call to invoke OCA when
encountering a busy station.
Send DTMF tones as a complete number rather than digit-by digit.
Used to enable E911 calling across a QSIG network. The QSIG ILG is
assigned to an Emergency Call Group in the same way a station is in
Program 200 FB17. Without this assignment, the call will not attempt
to complete to one of the trunks in the Emergency Group and will
result in an abandoned call. See Program 550
Emergency Call Group"
Enter the Tenant number to which this DID should be assigned.
This command deletes Incoming Line Groups.
Enter the ILG number to delete.
OLG is a line selection feature which enables the use of external
trunk or private line groups for outgoing service. Assign and configure
up to 128 OLGs (the same line can be placed in an OLG and an ILG).
Enter the OLG Group number.
Select the OLG Type.
Select the Trunk Type.
Strata CTX Programming - Part 3: Telephone Button Programming 6/04
Summary
"Enhanced 911
on
page
13-87.