Download Print this page
Most useful pages: More

Advertisement

726+,%$
Digital Solutions Division
Strata CIX and CTX
Telephone Button Programming Manual
November 2004

Advertisement

Chapters

   Also See for Toshiba Strata CIX

   Related Manuals for Toshiba Strata CIX

   Summary of Contents for Toshiba Strata CIX

  • Page 1

    726+,%$ Digital Solutions Division Strata CIX and CTX Telephone Button Programming Manual November 2004...

  • Page 2

    Strata and SmartMedia are registered trademarks of Toshiba Corporation. Stratagy is a registered trademark of Toshiba America Information Systems, Inc. Windows is a registered trademark of Microsoft Trademarks, registered trademarks, and service marks are the property of their respective owners...

  • Page 3: Table Of Contents

    Station Programming Error Codes ..................... 2-5 Trunk Programming Error Codes ..................... 2-13 Attendant Position Programming Error Codes ................. 2-20 Service Programming Error Codes....................2-21 Networking Programming Error Codes..................... 2-26 Equipment Programming Error Codes ..................... 2-27 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 4

    This page is intentionally left blank.

  • Page 5: Record Sheet Overview

    Telephone Button Programming This chapter discusses the button programming interface provided with Strata CIX / CTX. This chapter also includes Button Programming examples, procedures, and tables to program 100~800 series programs. This chapter has tables that list programs sequentially by program number. Tables found below a program table contain required information for the above program.

  • Page 6: Telephone Button Overview

    FB07 FB17 FB07 FB06 FB16 FB06 FB05 FB15 FB05 FB04 FB14 FB04 FB03 FB13 FB03 Spdial FB02 FB12 FB02 Redial FB01 FB11 FB01 Spkr Cnf/Trn Hold 6929 Figure 1-2 DKT3010/3020 and IPT1020-SD Button Telephones Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 7: Hold ✱#✱#1✱2✱3

    Network IP addresses are entered using sub-parameter data. IP addresses are displayed as four three- digit values, or Octets, separated by ìperiodsî (e.g., 192.168.255.253). Your programming telephoneís LCD is only capable of displaying the IP information three digits, or one Octet, at a time. Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 8

    Note To change one of the sub-parameters, you must proceed through all three sub-parameters before Hold pressing . For example, to change the value of COS DAY1, you must change the COS DAY1 Spkr Hold value, then press twice, and finally, press Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 9: Press Fb01

    Telephone Button Programming Button Programming Examples Button Programming Examples The following examples show you how to use the Strata CTX button programming interface. Toshiba highly recommends the use of Strata CTX WinAdmin to meet the demands of your telephone system programming.

  • Page 10: Program 204

    ABR attempts and press FB02 Hold 5. Press . Press to set ABR to attempt redials in 60 second increments and press FB03 Hold 6. Press . Press to set the ABR Recall Timer and press Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 11: Button Programming Procedure

    This table is a list of programs found in this chapter. Program Program Name Number Card Slot Assignment Flexible Access Codes Class of Service System Timers System Parameters Day/Night Mode Day of Week Mapping Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 12

    ISDN Trunk Delete Incoming Line Group Assignment ILG Delete Outgoing Line Group Assignment OLG Delete Trunk Timers Direct Inward Dialing DIT Assignment MOH Source DID Delete Caller ID Assignment T1 Trunk Card Shared D Channel Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 13

    DR LCR Screening Table Assignment DR Screening Table for OLG DR Table Allow/Deny Definition DR Level Table Assignment DRL Exception Table Assignment Pilot DN Assignment Pilot DN Delete Enhanced 911 Emergency Call Group Number Account Code Digit Length Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 14

    900 series programs. Tables immediately following a program table are provided for reference. For example, the PCB Code table shown after the Program 100 table gives important PCB codes needed in Program 100. 1-10 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 15: Series Programs

    Codes: 012, 013, 015, 016 FB01, nnn, Hold, FB04, n, Hold, 1. None Hold 2. 8 DKT no OCA 3. 8 DKT w/ OCA 4. 16 DKT no OCA 5. 16 DKT w/ OCA 1-11 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 16

    Value No Data #441 ABR - Activate #442 ABR - Cancel Call Park Orbits - Activate Call Park Orbits - Park Answer (Retrieve Parked Call) 7000~7019 System Orbit Number #6091 DND -Local Activation 1-12 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 17

    Call Forward (Any Call) - Remote Cancellation #6054 Call Forward (External Call) - Remote Cancellation #670 Change Password for Remote Activation/Cancellation Input Account Code #658 Change DISA Security Code Outgoing Call by Directing Individual Trunk 1-13 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 18

    Originate Call with Sub Address -Outgoing Call/Internal Call Application starting access code #963 Voice Mail Call Monitor Off #651 System Date Adjust Code (Release 1.02, MA227 or higher) #652 System Time Adjust Code (Release 1.02, MA227 or higher) 1-14 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 19

    The privilege to pick up a ringing station in a specified group. Pickup 2. Disable FB14 Hold Hold , n1, 103-15 Directed DN Call n1 = 1. Enable (default) The privilege to pick a specified DN. Pickup 2. Disable FB15 Hold Hold , n1, 1-15 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 20

    FB34 Hold Hold , n1, 103-35 Allow Long Hook n1 = 1. Enable The privilege to use a Long Flash signal over outside lines. Flash 2. Disable (default) FB35 Hold Hold , n1, 1-16 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 21

    (default = 5) 911 or 9+911 dialed codes for treatment using the E911 procedures FB13 Hold Hold , n, rather than normal dialing treatment. 1-17 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 22

    CO line button appearance. 105-05 Privacy Override 1. Enable Privacy Override Attendant Monitor warning Enable or Disable. 2. Disable (default) FB05 Hold Hold , n, 1-18 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 23

    Conference connection of many member for Analog Internal Call and 2. Disable (default) Outgoing Call. FB16 Hold Hold , n, 105-17 Caller Number 1. Enable (default) Caller number display preferentially. Display 2. Disable FB17 Hold Hold , n, 1-19 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 24

    Hold , n, 105-25 DP Make Ratio 1. DPMakeRatio33 Dial pulse Make/Break ratio can be set to 33% or 40%. The default 2. DPMakeRatio40 value is 40%. FB25 Hold Hold , n, (default) 1-20 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 25

    To PAD is to insert loss; therefore, negative loss equals net 4. 3 dB Net Loss gain. 5. 6 dB Net Loss 6. 9 dB Net Loss 7. 12 dB Net Loss 8. 15 dB Net Loss 1-21 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 26

    (Conference Bridge is only one) value = 4. Music Source 1~15 (Music Port) if Music port = 8, value = 58. External Paging Device 1~8 (Zone Relay Number) if External Paging Device = 3, value = 63. 1-22 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 27

    CTX and from updating the CTX software. 110-01 Password n1 = Up to 16 digits Enter a 1~16 digit password for the selected level. Each level can have only one password. FB01 Hold Hold , n1, 1-23 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 28

    = hour (00~23) Enter the start time for Day2 Mode for the Holiday type of day. Enter mm = minute (00~59) ì9999î to omit this mode. FB08 Hold , hhmm, 9999 to delete 1-24 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 29

    This program is used to initialize the tables of selected programs in the Strata CTX system. Hold FB01 Hold Hold 116-01 , n, 3 digit Program Number Enter Program Number to be initialized. (100~999) ìData Initialize Programsî page 1-26. 1-25 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 30

    ìxî and ìnî where x = 0~9 and n = 2~9. Hold 117-01 Digits to Follow n1 = 1~64 The total number of digits in a number beginning with the Prefix Number above. FB01 Hold Hold , n1, 1-26 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 31

    BIOU relays 1~8. This operation activates the relay when a CO line or FB05 Hold , n, ACTU = relay 5 DID rings when the system is in night mode. The CO or DID line must be assigned to ring the night bell. 1-27 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 32: Series Programs

    FRL for Day2. • Day2 FRL FRL for Night. • Night FRL FB06 Spkr , n, , n, Spkr Hold , n, 200-07 LCR Group 1~16 Station LCR Group Number. FB07 Hold , n, 1-28 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 33

    PDN that forward to voice mail (see Program 580 for SMDI or DTMF choice). 200-22 Message Waiting to Up to 5 digits Message Waiting Center DN. VM Port FB22 Hold , n, 1-29 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 34

    Voice Mail message waiting, or if DND is set. This feature is available with Strata CTX R1.3 software. Disable: This station will receive normal dial tone when it has a station-to-station or Voice Mail message waiting, or if DND is set. 1-30 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 35

    1. National ISDN Protocol 2. ETSI FB03 Hold , n, 3. TTC 4. National ISDN - Nortel 202-04 Type Connection 1. Point to Point Connection format 2. Point to Multi Point FB04 Hold , n, 1-31 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 36

    2. Backward Cyclic 3. Forward Terminal FB17 Hold , n, 4. Backward Terminal 202-18 Interdigit Timer 1 1~180 Interdigit1 Timer FB18 Hold , n, 202-19 Interdigit Timer 2 1~180 Interdigit2 Timer FB19 Hold , n, 1-32 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 37

    Disable: This station will receive normal dial tone when it has a a station-to-station or Voice Mail message waiting. 202-39 Tenant Number 1~8 (default = 1) Enter the Tenant number to which this PDN should be assigned. FB39 Hold Hold , n, 1-33 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 38

    For each iES32 PDN, set to ìTone Firstî, if set to Voice First iES32 will not answer. 204-06 OCA Type 1. Handset Select the OCA type. This field must be programmed with Auto OCA 2. Speaker Originate below. FB06 Hold , n, 1-34 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 39

    Preferenceî choices. The PDN button has first priority for idle selection, the lowest numbered DN button on the telephone has priority over other DN buttons for idle selection if the PDN button is busy. 1-35 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 40

    Hold , n, 204-26 Speaker Mode Tones 1. Yes Enable telephone to receive Call Waiting (Camp-on) and Ring Over 2. No Busy Tone while on a speaker phone call. FB26 Hold , n, 1-36 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 41

    If Call Forward Busy/No Answer is set, the telephone will Ring No Answer and then forward when a call is delivered to the telephone while the user is talking on a DN or CO line button. 1-37 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 42

    CO 3 CO 3 FB05 CO 4 CO 4 None FB06 CO 5 No Data FB07 CO 6 Single Touch Button FB08 CO 7 FB09 CO 8 FB10 Do Not Disturb Do Not Disturb 1-38 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 43

    205-00 Primary DN 0~99999 Enter a Primary DN number to program FBs. Hold Note FB04 Add on Modules in Program 204 must be set to One or Two. 1-39 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 44

    = ìFeature/Button Code This Parameter is required for Feature Codes 130 only. Parameter Assignmentsî n5, see Note page 1-41. Note For Feature Code 130, make your selection and push Spkr for further options. 1-40 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 45

    DN in DSS Key for one digits with CTX station. Release 1.3 or higher software. Up to 5 digits for releases earlier than 1.3. Start Parameter 1 Enter Application Enter a value between APL NO= Application number. 0~99. 1-41 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 46

    On hold - Directed DN Retrieve • On hold and Incoming - Any External Call • On hold and Incoming - Calling Number Identification (CLID) Dialing • Dial Out Do Not Disturb (DND) 1-42 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 47

    Up to 5 digits Set PhantomDN's Owner Station FB01 Hold , n, 206-02 Tone/Voice First 1. Tone First (default) Select from Tone first, or Voice first signaling. 2. Voice First FB02 Hold , n, 1-43 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 48

    Up to 5 digits Enter Primary DN of DKT. Hold 207-01 Feature Key Number 1~2860 Enter the feature number of the one touch button that registers the operating data. FB01 Hold , n, 1-44 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 49

    [Vol Up] + [Page] &SK02 Scroll [Vol Up] + [Scroll] &SK03 Feature [Vol Up] + [Feature] &SK04 [Vol Up] + [Msg] &MSG [Vol Up] + [Mic] &MIC Spkr [Vol Up] + [Spkr] &SPK 1-45 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 50: Hold Key

    FB06 Hold , n, 208-07 Ring Xfer No Answer 0~600 Select the Ring Transfer Idle station or Busy station (Camp-on) Recall Timer Time (in seconds). (default = 32) FB07 Hold Hold , n, 1-46 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 51

    Enter a Primary DN plus an ADM number to Program ADM FBs. Hold Note FB04 Add on Modules in Program 204 must be set to One or yyyyyx, ADM (1 or 2) Two. 1-47 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 52

    This Parameter is required for Feature Codes 130 only. Assignment Feature Code n5, see Note Tableî page 1-42 Note For Feature ìFeature/Button Code Code 130, Parameter Assignmentsî make your page 1-41 for more selection and Spkr for details. push further options 1-48 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 53

    = Primary DN (0~99999) Enter a Primary DN plus DSS Key Assignment button to program DSS FBs. Hold DSS (1~8) yyyyyx, Note FB04 Add on Modules in Program 204 must be set to One or Two. 1-49 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 54

    This Parameter is required for Feature Codes 130 only. Assignment Feature Code n5, see Note Tableî page 1-42 Note For Feature ìFeature/Button Code Code 130, Parameter Assignmentsî make your page 1-41 for more selection and Spkr for details. push further options 1-50 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 55

    Whether to put the user name in the list display. 2. Disable FB12 Hold Hold , n, Station Hunt Group This assignment configures station DNs to hunt groups and assigns Assignment the order of rotation in which the DNs are hunted. Hold 1-51 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 56

    Notify Data Delete entered in this screen. Hold 219-00 Network DSS Node Important! Don’t use this program unless requested by Toshiba Technical Support. Hold Enter the Node ID of the Network DSS key Notify Data to be deleted. 1-52 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 57: Series Programs

    This function is accessible only through CTX WinAdmin. 300-10 External Ring Repeat 1. Supplied (default) Supply the External Ringing Signal pattern to stations. For behind 2. Not Supplied PBX/Centrex trunks. FB10 Hold , n, 1-53 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 58

    Channel Group, then Call-by-Call Services must be used. (default = 0) 302-05 Trunk ID Type 1. Implicit Identify whether the communication with the PSTN requires an 2. Explicit identifier. Select Explicit to require an identifier. FB05 Hold , n, 1-54 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 59

    Sets this span as Side A or Side B for Layer 3 of a QSIG PRI. The 2. Side B opposite value must be set for the node in which this QSIG PRI FB27 Hold , n, terminates. 1-55 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 60

    Outgoing Line Group Assignment 306. The same line can be placed in an ILG and OLG. Hold 304-00 Group Number 1~32 (CTX100) Enter the group number of the line group that should be configured. 1~50 (CTX670 Basic) Hold 1~128 (CTX670 Exp.) 1-56 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 61

    Select in box to toggle Automatic Camp-on. 2. Disable FB17 Hold , n, 304-18 Calling Number ID 1. User Provided Select Calling Number Identification source. (default) FB18 Hold , n, 2. Network Provided 1-57 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 62

    1~128 (CTX670 Exp.) 306-01 Group Type 1. Analog (default) Select the OLG Type. 2. ISDN FB01 Hold , n, 306-02 Trunk Type 1. CO (default) Select the Trunk Type. 2. Tie FB02 Hold , n, 1-58 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 63

    Send CESID 1. Enable Enable CESID sending. 2. Disable (default) FB16 Hold , n, 306-17 QSIG Sending Type 1. Cut through (default) Digit sending Mode for QSIG only. 2. Senderized FB17 Hold , n, 1-59 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 64

    Select the ILG number. 1~50 (CTX670 Basic) Hold, 1~128 (CTX670 Exp.) 309-01 DID Number 1~7 digits may include wild Enter a DID number. card ì?î where ì?î = 0~9 FB01 Hold , n, 1-60 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 65

    #31 was changed, use the new page access code as the leading digits. Line access codes and network routing numbers can also be entered to route incoming calls back out to a public or private network number. 1-61 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 66

    CTX670 ñ Select 01 for Base and 02~07 respectively for each Expansion cabinet. Slot numbers: • CTX100 ñ Select 01~04 for Base slots and 05~08 for Expansion slots. • CTX670 ñ Select 01~08 for Base slots and 01~10 for Expansion slots. 1-62 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 67

    Hold, Hold they call into the system. , n, DID Number Delete This command deletes DID Number. Hold ILG Number 1~32 (CTX100) ILG Number. 312-00 1~50 (CTX670 Basic) 1~128 (CTX670 Exp.) (default = 0) 1-63 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 68

    , n, 3. ESF mode (default) 315-03 Time Slots 1. None Set the number of Time Slots to be used. 2. 8 Time Slots (default) 3. 16 Time Slots 4. 24 Time Slots 1-64 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 69

    ISDN BRI Trunk The following program enables set up for ISDN related system settings. Hold 317-00 Channel Group 1~32 (CTX100) Enter the BRI channel Group Number. 1~48 (CTX670 Basic) Hold 1~128 (CTX670 Exp.) 1-65 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 70

    Explicit ñ Channel is indicated, and no alternative is acceptable. 3. Any Channel • Preferred ñ (default) Channel is indicated, and any alternative is acceptable. • Any Channel ñ Channel is indicated, and any channel is acceptable. 1-66 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 71

    Hold , n, Table 1-30 Bearer Capability Table Bellcore Bearer Services ETSI National ISDN Speech 3.1 KHz 7 KHz 64 Kbps Circuit Mode Rate adaptation from 56 Kbps Unrestricted Digital Information 2x64 Kbps 1-67 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 72

    Night Bell ñ Assigns the line to cause the night relay to pulse (one-sec.close/3-sec.open) Audio Day1/Day2/ n1 = Up to 32 digits Enter the Destination Directory Number. Destination DN is only Night Dst DN required if the destination type is ìDialing Digitsî Hold 1-68 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 73

    VM port answers a DID/DNIS call as explained above. These digits are sent to the VM port if the CTX is set for SMDI or DTMF integration in Program 580, 01. 1-69 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 74

    Default Number Up to 10 digits Enter the telephone number to use by default when originating a call. This is the number that the PSTN has registered for billing purposes. FB01 Hold , n, 1-70 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 75

    9. INWATS 323-03 Facility Code 00~31 Enter the supplied Facility code value from the PSTN. If no data is entered in this field, any previously entered data is deleted. FB03 Hold , n, 1-71 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 76

    Enter the Time Zone Starting Time (hhmm). mm = minute (00~59) FB01 Hold , hhmm, 9999 to delete 324-02 Start Zone 2 FB02 Hold , hhmm, 324-03 Start Zone 3 FB03 Hold , hhmm, Hold 1-72 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 77: Series Programs

    Hold • Assign the 3rd ILG to ICI Groups 1~10. • Assign the 4th ILG to ICI Groups 1~10. Note Each ILG can only be assigned once in any of the ICI Groups. 1-73 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 78: Series Programs

    Activate the Paging Group(s) this station belongs too. The number of 01~16 2. Off (default) DNs that can be assigned are 1~4 (CTX100), 1~8 (CTX670 Basic), FB01 FB16 Hold , n, 1~16 (CTX670 Exp.) 1-74 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 79

    Enter a valid accounting code that the user will be expected to dial. Digits 0~9 can be used. Hold Note The Account Code is set to the same digit length as the Verified Digit Length in Program 570 above. 1-75 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 80

    DDCBs are numbered by the system automatically by DDCB Equipment (Shelf/Slot/Circuit). DDCB1 is assigned to the lowest DDCB Equipment and DDCB2 to the next lowest, etc. If DDCB Circuit B is set to Door Lock, a Door Phone cannot be set. 1-76 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 81

    1~4 (CTX100) PDN or PhDN, enter the directory number. If the ring destination 1~8 (CTX670 Basic) type is Page, enter the Page Group number. 1~16 (CTX670 Exp.) n1 = Up to 5 digits 1-77 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 82

    Hold , n, 509-02 Override DRL 1~16 Select the override DRL value. (default =1) FB02 Hold , n, 509-03 Override FRL 1~16 Select the override FRL value. (default =1) FB03 Hold , n, 1-78 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 83

    FB02 Hold , n, 513-03 B Record for Incoming 1. Enable Enable B Record generation for incoming calls with or without Call 2. Disable (default) incoming SMDR being enabled. FB03 Hold , n, 1-79 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 84

    Night Mode (see ìProgram 105î on page 18). • DOOR LOCK ñ Door Lock Control activates when a telephone's Door Unlock button is pressed (see ìProgram 508î on page 78). 1-80 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 85

    516-03 Name Up to 8 characters Enter the LCD Name that displays on LCD dial directories. FB02 Hold Hold , n, Note This feature is available in CTX WinAdmin and Strata DKT30xxSD only. 1-81 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 86

    Local calls are made by dialing 7-digit public telephone numbers FB02 Hold Hold , n, that do not require an Area Code. There are 64 LCR Route Plans from which to choose. 1-82 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 87

    , n, 523-04 Route Choice Table 1~128 Enter the Route Choice Table Number to be used with this (default = 1) combination of time, type and LCR group. FB04 Hold Hold , n, 1-83 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 88

    DD = 527-01 Add/Delete 1. Add Choose to add or delete this date from the holiday table. Expired 2. Delete (default) dates remain in the table unless deleted. FB01 Hold Hold , n, 1-84 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 89

    2. Skip and Apply FB02 Hold • , n, Bypass ñ Do not apply DR. • Skip and Apply ñ Apply DR to the dialed digits excluding the number of digits specified in Skip Length. 1-85 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 90

    Add or delete the string entered in 01 DR Exception Table above to 533-02 Add or Delete n2 = 1. Add 2. Delete (default) the DR Exception Table. FB02 Hold Hold , n2, 1-86 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 91

    550- OLG1~OLG8 0~32 (CTX100) Specify the first through eighth OLG to be chosen for an E911 call. 01~08 0~50 (CTX670 Basic) FB01 FB08 Hold , n, 0~128 (CTX670 Exp.) Hold (default = 0) 1-87 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 92

    Up to 6 digits Enter the Circuit Type and number. See the Table 1-36 page Hold 577-01 Primary DN Up to 5 digits Enter Station DN to store call history data. FB01 Hold Hold , n, 1-88 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 93

    FB08 Hold , n, 579-09 LCD Control of Voice 1. Enable (default) Enables Toshiba SMDI+ and integration for LCD control of VM. To Mail 2. Disable enable this feature you must have Stratagy Enterprise Server Release 3.x or higher. FB09...

  • Page 94

    3. B Tone and Extension Number 580-04 End-to-end 1. Enable (default) Enable Strata CTX to send DTMF tones to voice mail in response to 2. Disable key presses from a digital telephone. FB04 Hold Hold , n, 1-90 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 95: Series Programs

    1~128 (CTX670 Exp.) 0 = delete 654-02 Digit Modification 0~64, 0 = delete Enter the Digit Modification Table Number (1~64) to be used by this Table route definition. FB02 Hold Hold , n, 1-91 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 96

    Node ID for further call Overlap Code 4 processing. FB04 Spkr , n, , n1, n1 = Up to 4 digits The privilege to pick a specified DN. Hold Hold 1-92 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 97

    This program deletes Node IDs. Private Networking Over IP Hold 673-00 Node ID upto six digits Delete Node ID Hold 673-01 Registration State 1. doesnít exist Delete Registration State. 2. exist FB01 Hold , n, 3. delete 1-93 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 98: Series Programs

    Devices of PCs (default = SMDI: 300 or 301 no value) 400 = BLF CTI LAN devices or PCs can be assigned to any of the 9 LAN devices 500 = DSS numbers available: 200~208. 1-94 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 99

    LAN Port3=device202 LAN Port4=device203 LAN Port5=device204 LAN Port6=device205 LAN Port7=device206 LAN Port8=device207 Table 1-40 Device Table Physical Device Define I/O Logical Logical Device Logical Smart Device Serial Number Device RS-232C Media Number SMDR SMDI 1-95 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 100

    804-05 Wait Timer 0~255 Maximum time to wait for connection. FB05 Hold Hold , n, (default = 30 seconds) 1. 0 means wait permanently 2. Timer value can be 1-255 seconds. 1-96 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 101: System Initialize

    Note During the restore process, the telephone LCD may display date and time data. This does not necessarily indicate completion of the restore process. 1-97 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 102: Enter Another Program Number To Continue Programming Or Press Mode

    N A 1 0 2 M A 2 X X P 1 D 1 2 B X S E M . 0 0 - Release 1.02 N A 1 0 3 M A 3 X X P 1 D 1 2 B X S E M . 0 0 - Release 1.03 6499 1-98 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 103

    “-” displays. The following are the equipment identifier designations. • B ñ BBMS is installed. X ñ BEXS is installed. • • S ñ BSIS is installed. • E ñ The Ethernet is installed. M ñ The Modem is installed. • 1-99 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 104: Set Time And Date

    Login to programming mode from your telephone button pad: Hold ✱#✱#1✱2✱3✱ . At the PASSWORD= prompt, Enter your password and press Hold . At the PROG= prompt enter 903 and press Hold . 1-100 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 105

    Note When CTX 670 stops logging data, it automatically sends data to the SmartMedia card. A new trace Evnttrace file is stored on SmartMedia under the directory. Run the Unmount command (Program 908) before removing the SmartMedia card to ensure complete data transfer. 1-101 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 106: Isdn Trace Location

    7. Press to execute. # # Hold 8. Press to return to the = prompt. PROG # # Hold 9. Enter another program number to continue programming or press again to exit programming mode. 1-102 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 107: All Isdn Trunk Trace

    Note When the CTX 670 stops logging data, it automatically sends data to the SmartMedia card. Run the Unmount command (Program 908) before removing the SmartMedia card to ensure complete data transfer. 1-103 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 108: Program Number(s): 907

    = prompt to appear before proceeding. Note When the CTX 670 stops logging data, it automatically sends data to the SmartMedia card. Run the Unmount command (Program 908) before removing the SmartMedia card to ensure complete data transfer. 1-104 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 109: Format/unmount Smartmedia

    • Progdata – Your Strata CTX programmed settings are all saved in this folder. • Program – The operating software and default data of the Strata CTX is saved in this folder. When a backup is performed, Strata CTX saves programmed data to the Progdata folder. 1-105 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 110: Mac Address (system Serial Number)

    Current Number This number increments as the backup Variable CUR NO= progresses. When the backup is complete this number should match the total number of data blocks displayed in Numbers (FB02). 1-106 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 111

    5. Press to exit. Hold Hold Note Do not press the button. Pressing the button restarts the Backup procedure. To Restore data from the SmartMedia card to Strata CTX, see ìSystem Initializeî page 1-97. 1-107 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 112: Program Update

    When an error occurs in hardware resources used for a station or a line fails, this feature makes them busy. The station or line PCB can be disabled temporarily to perform maintenance or parts replacements as well. This program is only available in the telephone button programming mode. 1-108 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 113

    • Red continuous illumination – PCB Make Busy Status mode is on. • Green continuous blinking – PCB Make Busy Status mode is stand by. • Green intermittent blinking – PCB Make Busy Status mode is idle. 1-109 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 114: Regional Selection

    Mexico = 2). FB01 Hold 1. Press . Enter . Press Hold 2. Press (twice). # # Hold 3. Enter another program number to continue programming or press again to exit programming mode. 1-110 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 115: Ip Configuration

    9. After all parameters are entered press to submit the new settings. 10.You are automatically returned to the = prompt. PROG # # Hold 11. Enter another program number to continue programming or press again to exit programming mode. 1-111 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 116

    This page is intentionally left blank.

  • Page 117: Common Error Code Table

    System Error Codes The following Error Code Tables are needed when programming Strata CIX and CTX systems using the button programming method. Error Codes display on the programming station LCD. Note The following error codes only appear when using the telephone button programming method.

  • Page 118: System Programming Error Codes

    FB00 value entered cannot be registered (e.g., If 1234 is registered, 123 cannot be registered). The value entered conflicts with an existing extension and FB00 cannot be registered. ìCommon Error Code Tableî page 2-1. Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 119

    The inputted analysis number is using in a part of the other FB00 analysis number. FB01 Incorrect Master ID code. Common error. See Common Error Code table. FB09 Incorrect value. The values should be numerals only. Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 120

    FB01 assigned to CTX or another BIPU. This restriction is only applied to the duplication of global IP addresses. FB01 You cannot use 1:10msec in this release. Common error. See Common Error Code table. Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 121: Station Programming Error Codes

    The desired value conflicts with existing ISDN extensions. The Primary DN entered conflicts with a value of an existing numbering scheme. FB00, FB26 The desired value conflicts with existing number schemes. ~FB32 FB00 A DN used for DKT extensions is designated. Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 122

    The line number entered is out of range for the system's capacity. The GCO key group/index entered is out of the range. The POOL group entered is out of the range. The BGM number entered is out of the range. Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 123

    The sub-parameter values assigned to the FB are invalid. The line number entered does not exist. The maximum allowable value for GCO, POOL, or PhDN has been exceeded. FB01 The quantity of Flexible keys programmed exceeds the FB04 system's capacity. Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 124

    The entered Prime DN does not exist in the system. The Pickup group number entered is out of the range for the system's capacity. The hunting group number entered (FB00) is a number that does not exist in the system. Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 125

    The secondary/PhDN entered cannot be registered. The FB01 number conflicts with an existing ISDN extension(s), etc. The CO or GCO Owner DN entered does not exist. FB01 FB00 The specified Prime DN does not exist in the system. Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 126

    The door lock number entered is out of the range. The application number entered is out of the range. Essential sub-parameter values must be entered. Two or more PhDNs with the same value are registered to one FB01 extension. 2-10 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 127

    FB00 value conflicts with an existing extension number or numbering plan). The entered DN conflicts with an existing ISDN extension(s), FB00 etc. FB00 The designated Prime DN does not exist in the system. 2-11 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 128

    The DN entered is an extension number that does not exist in the system. FB which this error occur : FB00 Note For FBs in Program 205, 213 and 215, codes shows the entered Feature Code. 2-12 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 129: Trunk Programming Error Codes

    Allowable number of trunks has been exceeded. FB00 The line number entered exceeds the system's capacity. FB01 The trunk number entered is out of the range. A trunk number that does not exist in the system has been selected. 2-13 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 130

    The designated ILG does not exist in the system. FB04 The designated OLG does not exist in the system. The number of allowable Channel Groups has been exceeded FB00 when a new ISDN trunk assignment is made. 2-14 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 131

    The OLG entered is out of the range. The entered OLG number cannot be deleted. Trunk FB01 relationships assigned in Programs 300 and 302 must be deleted first. FB01 The entered OLG does not exist in the system. 2-15 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 132

    The Signalling Contents field value must be assigned FB03 • The CLID Equipment Number Position circuit for the CIU must be entered. FB00 The entered trunk number does not exist in the system. 2-16 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 133

    The entered circuit must be an assigned ISDN. FB03 The entered ILG number does not exist in the system. FB04 The entered OLG number does not exist in the system. The allowable channel group assignments exceed the system FB00 capacity. 2-17 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 134

    The entered GCO value does not exist in the system. FB02 FB01 The entered POOL value does not exist in the system. FB02 FB00 The OLG entered is out of the range. FB03 The allowable system DID assignments has been exceeded. 2-18 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 135

    The entered channel group number does not exist in the FB00 system. The Channel Group entered does not exist in the system. The allowable number of assigned channel groups has been FB01 exceeded. The number of allowable CBCs has been exceeded. 2-19 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 136: Attendant Position Programming Error Codes

    The Attendant group number entered is out of the range. FB07~FB16 The ILG entered is out of the range. The entered Attendant group number does not exist in the FB00 system. FB07~FB16 The designated ILG does not exist in the system. 2-20 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 137: Service Programming Error Codes

    Account Code cannot be verified. Account code confirmation digit does not coincide. (It is larger FB00 than the value that was registered by Program 570.) FB00 The Account code number exceeds the system's capacity. 2-21 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 138

    ILG number enter does not exist. FB00 The OLG entered is out of the range. FB00 The entered OLG number does not exist. No error occurs for this Program except for common errors. 2-22 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 139

    The allowable number of participants in the Route Plan Table has been exceeded. No error occurs for this Program except for common errors. No error occurs for this Program except for common errors. 2-23 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 140

    To add a DRL to the DR Exception Table, the DRL number FB01 must be complete. The allowable number of participants in the DR Exception FB01 Table has been exceeded. FB01~FB09 The value entered is not permitted. 2-24 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 141

    The entered station number does not exist. No error occurs for this Program except for common errors. The entered DN is not a VM extension. No error occurs for this command except for common errors. 2-25 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 142: Networking Programming Error Codes

    The Node ID entered is using a part of the registered Node ID. FB00 The Node ID entered is out of the range. FB00 The Node ID entered is using a part of the registered Node ID. FB01 The Node ID entered is not registered. 2-26 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 143: Equipment Programming Error Codes

    The selected port conflicts with existing devices, such as CTI, etc. The Physical Device assignment conflicts with existing serial number assignments. The values assigned in Program 803 conflict with related I/O Logical and Physical Device assignments. 2-27 Strata CIX/CTX Telephone Button Programming 11/04...

  • Page 144

    This is the last page of the document.

This manual also for:

Strata ctx

Comments to this Manuals

Symbols: 0
Latest comments: