Toshiba Strata CTX28 Programming Manual page 343

Table 13-5 Programs 103~107 (continued)
Button Sequence
105-06 Credit Card Code
A7% C‚yq C‚yq
, n, ,
105-07 Credit Card Digits
A7& C‚yq C‚yq
, n, ,
105-08 E911 Service
A7' C‚yq C‚yq
, n, ,
105-09 DR Override by SSD
A7( C‚yq C‚yq
, n, ,
105-10 Auto Station Release
A7  C‚yq C‚yq
, n, ,
105-11 ISDN SPID
A7 C‚yq C‚yq
, n, ,
105-12 Night Mode Relay
A7 ! C‚yq C‚yq
, n, ,
105-13 BGM External Paging
A7 " C‚yq C‚yq
, n, ,
105-14 Lost Call Destination
A7 # C‚yq C‚yq
, n, ,
105-15 COS Override Code
A7 $ C‚yq C‚yq
, n, ,
105-16 Multi-Conference
A7 % C‚yq C‚yq
, n, ,
105-17 Caller Number
Display
A7 & C‚yq C‚yq
, n, ,
Strata CTX Programming - Part 3: Telephone Button Programming 6/04
Value(s)
n = Up to 32 digits
n = 1~66 digits
n = 1. Enable (default)
2. Disable
n = 1. Enable (default)
2. Disable
n = 1. Enable (default)
2. Disable
n = 1. Operable
2. Not Operable (default)
n = 0~8
n = 0~4 (CTX100)
0~8 (CTX670 Basic)
0~16 (CTX100 Expanded)
n = Up to 5 digits
n = 1~8
(default = 1)
n = 1. Enable
2. Disable (default)
n = 1. Enable (default)
2. Disable
Telephone Button Programming
Summary
Enter the number dialed to initiate a Credit Card Call. This is normally
"0" in the USA.
Minimum Dial Digits required for Credit Card Calling. This should be
the quantity of digits in a credit card number. If this quantity of digits is
not dialed when making credit card calls, the caller will be
disconnected. This is to insure that the call is charged to a credit card.
DRL tables in Program 111 and OLGs in Program 306 must be
enabled with credit card calling for this feature to be active. Users
must be assigned to a DRL table enable with credit card calling and
call out on a credit card calling enabled OLG for this featured to be
applied to the call.
Offer of E911 Service.
Destination Restriction Override by System Speed Dial.
Automatic Station Release.
Operation when Auto SPID or User Entry Of SPID fails.
Assign BIOU Relay (1~8) as the Night Relay - this relay activates
when the
system is in the Night Mode.
BIUO1 provides relays 1 to 4.
BIUO2 provides relays 5 to 8
Note The CTX100 ACTU built-in relay is programmed as relay 5.
For this relay operation, a virtual BIOU2 is installed, as
default, in a virtual equipment position - Cabinet 2 slot 5.
(Cab. 02 slot 05, PCB code 20, in program 100). To install an
actual BIOU2 and disable the ACTU built-in relay, use the
programming telephone. To remove the virtual BIOU2 and
then install the actual BIOU2 in Cab. 01/slot 01~08 in the
normal manner.
Set the External Page Group Number that includes the external
paging zones to which BGM will be sent. See PRG503.
Set Lost Call Destination.
Class of Service Override Code Digits.
Conference connection of many member for Analog Internal Call and
Outgoing Call.
Caller number display preferentially.
100 Series Programs
13-19