Table 13-26
Programs 300~302 (continued)
Button
Sequence
302-06
Trunk ID Number
A7%
Cyq
, n,
302-07
D Ch Position
A7&
Cyq
, n,
302-
Bearer Services:
08~13
•
Speech
•
3.1 KHz Audio
•
7 KHz Audio
•
Unrestr. 64K
•
Unrestr. 56K
•
Unrestr. 2x64K
A7'
A7 "
Tx
~
, n,
Cyq
n1,
302-
Bearer Services:
14~18
•
Unrestr. 384K
•
Unrestr. 1536K
•
Unrestr. 1920K
•
Restr. Digital
•
Video
A7 #
A7 '
Tx
~
, n,
Cyq
n1,
302-19
Bearer Service
Multirate Unrestricted
A7 (
Cyq
, n,
302-20
B Ch Selection
Method
A7
Cyq
, n,
302-21
B Ch Selection
A7
Cyq
, n,
302-22
T1 Time Slot Pattern
A7
Cyq
, n,
302-23
E1 Time Slot Pattern
A7 "
Cyq
, n,
302-24
T-Wait Timer
A7 #
Cyq
, n,
302-25
RBT on Incoming Call
A7 $
Cyq
, n,
302-26
Network Mode
A7 %
Cyq
, n,
302-27
Negotiation Priority
A7 &
Cyq
, n,
Strata CTX Programming - Part 3: Telephone Button Programming 6/04
Value(s)
n =
0~126
(default = 0)
n =
1~24
(default = 24)
n =
1. Enable
2. Disable
n1 =
1. Channel Number
2. Slot Map
,
n =
1. Enable
2. Disable (default)
n1 =
1. Channel Number B
2. Channel Number H
3. Slot Map B
,
4. Slot Map H
n =
1. Enable
2. Disable (default)
n =
1. Exclusive
2. Preferred
3. Any
n1 =
1. Forward Cyclic
2. Backward Cyclic
3. Forward Terminal
4. Backward Terminal
n =
1. Fixed1 (default)
2. Fixed2
3. Flexible
n =
1. Fixed1 (default)
2. Fixed2
3. Flexible
n =
1. Enable
2. Disable (default)
n =
1. Enable (default)
2. Disable
n =
1. Master
2. Slave (default)
n =
1. Side A (default)
2. Side B
Telephone Button Programming
Summary
An identifier must be used as part of the addressing when an "explicit"
identified is used to communicate with the PSTN which channel on
which link is used for the given call. This identifier is assigned by the
connected PSTN.
PRI includes a 64-kbps D-channel (for transfer of signal information).
Select the channel position to be used for D channel signaling.
Note
This field is used only when the span interface speed is 1.5M.
If the span interface speed is 2M the value is fixed at 16.
Enable the Bearer Capabilities allowed for this PRI Trunk channel
group.
Select the Channel Method (map) to identify the channels.
Note
In North America, only Channel Number map is used
(Channel Number).
The Bearer Capabilities (384k Unrestricted(H0), 1536k
Unrestricted(H11), 1920k Unrestricted, Restricted Digital Info, Trunk
Video, and Unrestricted Multirate) are not used and should remain
disabled.
Select the Channel Method (map) to identify the channels.
Note
In North America, only Channel Number B map is used.
The Bearer Capabilities 384k Unrestricted (H0), 1536k Unrestricted
(H11), 1920k Unrestricted, Restricted Digital Info, Trunk Video and
Unrestricted Multirate are not used and should remain disabled.
The method used for selecting an idle 'B' channel and the reaction if
the PSTN indicates the channel is not available needs to be chosen
to originate a call from CTX.
Preferred option is recommended, unless PSTN needs other choice.
The search method for choosing an idle 'B' channel shall also be
specified. Backward Terminal is the normal method with the PSTN
following a Forward Terminal method.
1544 Time Slot Pattern.
2048 Time Slot Pattern.
Specify whether the T-Wait timer is to be enabled or disabled. This
field is only valid for Nat'l ISDN.
Enable Ringback Tone when terminating a call. This field is only valid
for Nat'l ISDN.
Set this span as Master or Slave for Layer 2 of a QSIG PRI. The
opposite value must be set for the node in which this QSIG PRI
terminates. This governs call setup activity and is not related to clock
synchronization.
Sets this span as Side A or Side B for Layer 3 of a QSIG PRI. The
opposite value must be set for the node in which this QSIG PRI
terminates.
300 Series Programs
13-55