Beckman Coulter LH 780 Instructions Manual page 240

INDEX
Manual sampling probe wipe obstructed (not up)
(<Tube ID>, <Cass/Pos>),
Maximum # Of Repro runs Exceeded - Sample Not
Stored, 6-61
Maximum number of cassettes (12) already loaded,
obstruction or faulty switch,
Monitor Task Did Not Finish,
No ACK From Diluter,
No Calibrator lot number. No statistics will be
calculated, 6-62
No ETX, 6-33
No latex Setup Information available, latex sample
will not be stored,
NO MATCH: Sample run received does not match
any Todo list entry,
NO READ: Sample run received without proper
identification, 6-62
No Wand ID, 6-33
Non-ASCII From Diluter,
Not Ready For AMC Data,
Operator changed control lot to, 6-64
Operator <Operator ID> added <Location Name>
to the location list,
Operator <Operator ID> added <Physician's First
Name, Last Name> to from physician list,
Operator <Operator ID> added <Physician's First
Name, Last Name> to the physician list,
Operator <Operator ID> changed <Physician's
First Name, Last Name> to <Physician's First
Name, Last Name>,
Operator <Operator ID> changed Analytical
Station setup, 6-63
Operator <Operator ID> changed Database
setup, 6-63
Operator <Operator ID> changed Decision Rules
setup, 6-63
Operator <Operator ID> changed Display Labels
setup, 6-63
Operator <OPERATOR ID> changed Flagging
Units setup, 6-63
Operator <Operator ID> changed Institution
setup, 6-63
Operator <Operator ID> changed lis/his
setup, 6-63
Operator <Operator ID> changed location
<Location Name> to <Location Name>,
Operator <Operator ID> changed Parameter
setup, 6-63
Operator <Operator ID> changed Print setup,
INDEX-10
6-36
6-30
6-33
6-33
6-62
6-62
6-33
6-34
6-63
6-63
6-63
6-63
6-63
6-63
Operator <OPERATOR ID> changed Reporting
Units setup, 6-63
Operator <Operator ID> changed Shifts
definition, 6-63
Operator <Operator ID> changed Workstation
setup, 6-63
Operator <Operator ID> changed XB setup,
Operator <Operator ID> deleted <# 0f runs>
Run(s) from Control Folder <Lot #>,
Operator <Operator ID> deleted <Location Name>
from the location list,
Operator <Operator ID> installed <Reagent
Type><Coulter/Non-Coulter> Reagent Lot to:
<New Lot#>, opened on <Open Date> with open
expiration <Open Exp>,
Operator <Operator ID> requested Research Use
Only certification, 6-64
Operator <Operator ID> shutdown the GEN S
Workstation, 6-64
Operator <Operator ID> Started RAS,
Operator <Operator ID> Stopped RAS,
Operator Alert 09, 6-34
Operator removed sample from probe before
aspiration was complete (<Tube ID>,
<Cass/Pos>), 6-42
Operator selected assay limits for control folder
<Lot #>, 6-64
Operator selected laboratory limits for control
folder <Lot #>, 6-64
Overflow valve malfunction (remained closed)
detected while turning compressor ON,
OVERLARY AREA CRC ERROR,
P/W Harness Not Connected,
Password changed, 6-65
PC Not Receiving, 6-35
Peltier Heater Sensor Bad,
Peltier heater sensor defective or
disconnected, 6-35
Peltier Temp. Outside Limits,
Peltier temperature outside limits,
Pneumatics/Power Supply overheated or
defective, 6-16
Power Supply 1 problem: +15 Volts above
limit, 6-36
Power Supply 1 problem: +15 Volts below
limit, 6-36
Power Supply 1 problem: +5 Volts above
limit, 6-36
Power Supply 1 problem: +5 Volts below
6-63
6-63
6-63
6-64
6-64
6-64
6-23
6-16
6-38
6-35
6-35
6-35
PN 773023AC