Beckman Coulter LH 780 Instructions Manual page 236

INDEX
W
wait enable/disable, 5-26
wand, 2-33, 4-8
waste, 2-39, 3-27
clean chamber, 2-39
replace container, 3-27
WBC, 5-14, 5-23
wedge scanner, 2-33, 4-8
wipe, 5-22
Workstation Messages
Workstation Communications Timeout,
+15 Volts from Diff Power Supply outside
limit, 6-18
+15 Volts on Diluter 1 card outside limit,
+15 Volts on Diluter 2 Card outside limit,
12 Volts on Diluter 4 Card outside limit,
-15 Volts from Diff Power Supply outside
limit, 6-19
-15 Volts on Diluter 1 Card outside limit,
-15 Volts on Diluter 2 Card outside limit,
24 Volts on Diluter 2 Card outside limit,
30 PSI Pressure High,
30 PSI pressure too high,
30 PSI pressure too low,
48 Volt bulk or pneumatic Power Supply
defective, 6-15
48 Volt power outside ±10% limit,
5 PSI Pressure High, 6-7
5 PSI Pressure Low, 6-7
5 PSI pressure too high,
5 PSI pressure too low,
5 Volts on Diluter 1 Card outside limit,
60 PSI pressure high,
60 PSI pressure low, 6-26
60 PSI pressure out of range, 6-26,
A Control Lot number archive file was
created, 6-49
AC Line Voltage Bad,
AC line voltage below 90 Volt limit,
ACK Not Received By Diluter,
Ambient Temp Sensor Bad,
Ambient temperature sensor defective or
disconnected, 6-8
AMC Did Not Reply, 6-8
AMC Never Sent Start Command,
AMC reported error - ASCII Receive Error,
AMC Reported Error - Diff Transmit Failure,
AMC Reported Error - Function Not Allowed,
AMC Reported Error - PC not ready,
INDEX-6
6-48
6-20
6-19
6-21
6-21
6-20
6-20
6-7
6-7
6-7
6-9
6-7
6-7
6-20
6-26
6-27
6-8
6-8
6-8
6-8
6-8
6-10
6-19
6-25
6-35
AMC Reported Error - Retic Transmit
Failure, 6-39
AMC Reported Error - Run Aborted, PC Not
Ready, 6-41
AMC Reported Errors -- Operator Alert 09,
AMC Requested Stop, 6-9
AMC, Diluter or DIFF Processor hardware
malfunction (<Tube ID>, <Cass/Pos>),
AMC-DIFF communication failure
wrong echo, 6-48
AMC-DIFF communication failure: 286 board,
AMC-DIFF communication failure:
unknown, 6-47
An archive file with patient samples was
created, 6-49
Analyzer +48V Bad, 6-9
Analyzer Error, 6-9
Analyzer Fans Failed, 6-9
Analyzer Fans Power Supply Defective,
Analyzer fans power supply defective,
Analyzer memory read/write failure,
Analyzer non-communication error,
Analyzer stopped, 6-9
Analyzer-Diluter communication failure: two
NAKs sent from AMC,
Analyzer-Diluter communication failure: two
NAKs sent from Diluter,
Analyzer-Diluter communication failure:
unknown, 6-47
Analyzer-to-Diluter communication failure,
Aperture Voltage Lower Failed,
Aperture voltage reading above limits,
Aperture voltage reading below limits,
Aperture Voltage Upper Failed,
Aperture voltage(s) out of range (<Tube ID>,
<Cass/Pos>), 6-15
ASCII Rec. Error, 6-10
Aspiration -B--, 6-10
Aspiration ---C, 6-11
Aspiration N---, 6-11
Aspiration --P-, 6-12
Aspiration Timeout, 6-12
Aspiration timeout, 6-12
Automatic CBC calibration factors updated from
Analyzer, 6-49
Automatic CBC calibration factors updated from
analyzer, 6-49
Automatic CBC calibration factors updated from
GEN•S, 6-49
6-34
6-28
6-7
6-9
6-9
6-41
6-27
6-46
6-46
6-21
6-9
6-9
6-9
6-9
PN 773023AC