Beckman Coulter LH 780 Instructions Manual page 239

field, 6-56
Host: Non Numeric Char In Numeric Field,
Host: Nonnumeric Cass/pos Char In Testfield,
Host: Num Of Fields Mismatch in Preamble,
Host: NumberOf Fields Count is 0,
Host: Test request UPDATED No Valid Patient
ID, 6-57
Host: Time Format Incorrect,
Host: Time Format Incorrect, Non
Numeric, 6-57, 6-62
Host: Trailing Spaces In Field, 6-57,
ID MISMATCH: Sample ID received does not
match pre-assigned ID,
ID not read by wand or ID was not available,
Illegal Interrupt, 6-28
Incomplete Retic Collection,
Incomplete Retic collection,
Incorrect calibration factor transmission,
Incorrect calibration factors or bath voltages,
Instrument detected clog in flow cell and attempted
three times to clear clog without success,
Instrument dual port RAM memory test
failed, 6-24
Instrument has not performed a shutdown in <24>
hours. Beckman Coulter service recommends
shutdown every 24 hours,
Intermittent PS1 Supply Error,
Intermittent PS2 Supply Error,
Internal Cal. Fac. Error,
Internal software failure,
Interpreter Collator ABORT. Cannot allocate
graphics or Raw Data,
Interpreter Collator Forced to Reset,
Interpreter Collator has timed-out indicating a
possible Analytical Station malfunction,
Invalid character received from Diluter,
Invalid Diluter command,
Invalid dual port RAM packet (<Tube ID>,
<Cass/Pos>), 6-23
Invalid tube label type read by scanner (<Tube ID>,
<Cass/Pos>), 6-42
Keyboard Interrupt Error,
Label Not Read Run Stopped,
Laser offset too high, 6-17
Laser offset too low, 6-17
Laser voltage above limit (<Tube ID>,
<Cass/Pos>), 6-30
Laser voltage below limit (<Tube ID>,
<Cass/Pos>), 6-29
Laser Voltage Lower Failed,
PN 773023AC
6-56
6-56
6-56
6-57
6-57
6-63
6-58
6-33
6-39
6-39
6-45
6-48
6-25
6-65
6-28
6-28
6-28
6-44
6-58
6-58
6-58
6-33
6-33
6-28
6-29
6-29
Laser Voltage Too High,
Laser Voltage Too Low, 6-29
Laser Voltage Upper Failed,
Last CBC XM batch is out of limits,
Last CBC XM batch outside limits condition has
cleared, 6-59
Last Diff XM batch is out of limits,
Last Diff XM batch outside limits condition has
cleared, 6-60
Last Retic Calculated XM batch outside limits
condition has cleared,
Last Retic XM batch is out of limits,
Last Retic XM batch outside limits condition has
cleared, 6-60
Last two CBC XM batches are outside limits,
Last two Diff XM batches are outside limits,
Last two Retic Calculated XM batches are outside
limits, 6-61
Last two Retic XM batches are outside limits,
Last Two XB batches are outside limits,
Last XB Batch is outside limits,
Last XB batch outside limit conditions has
cleared, 6-59
Left Lift Not Up, 6-30
Left Load Fail, 6-30
Left Stack Full, 6-30
Level C------, 6-30
Level Check Fail Caused Stop,
Level -D-----, 6-31
Level --L----, 6-31
Level ---P---, 6-31
Level ----R--, 6-31
Level -----V-, 6-31
Level ------W, 6-32
Low Vacuum Drifted, 6-32
Low Vacuum High, 6-32
Low Vacuum Low, 6-32
Low vacuum too high, 6-32
Low vacuum too low, 6-32
Manual CBC calibration factors updated from
GEN S Workstation, 6-61
Manual Probe Not In, 6-33
Manual sampling probe did not retract (<Tube ID>,
<Cass/Pos>), 6-33, 6-35
Manual sampling probe wipe obstructed (<Tube
ID>, <Cass/Pos>), 6-35
Manual sampling probe wipe obstructed (not
down) (<Tube ID>, <Cass/Pos>),
Manual sampling probe wipe obstructed (not
home) (<Tube ID>, <Cass/Pos>),
INDEX
6-29
6-30
6-59
6-59
6-60
6-60
6-60
6-61
6-61
6-59
6-59
6-31
6-35
6-36
INDEX-9