Beckman Coulter LH 780 Instructions Manual page 237

Automatic Mode Disabled,
Automatic sampling mode disabled,
Auto-Numbering has been disabled,
Auto-Numbering has been enabled auto number is
<Auto-Numbering Start ID>,
Autostop has been triggered for Analytical Station
<Instrument#>, 6-49
AutoStop has been triggered for control folder
<lot#>, 6-50
Background CBC test values within limits,
Background DIFF test values within limits,
Background: <Background test/parameter>
<Background> exceeded <flag> limit,
Background: <Background
test/parameter><Background> exceeded <flag>
limit, 6-50
Backwash Tank Not Full,
Backwash Tank Still Full,
Bed Not Advanced, 6-13
Bed Not Backward, 6-13
Bed Not Forward, 6-14
Bed Not Level, 6-14
Bellows Not Down, 6-14
Bellows not extended,
Bellows Not Up, 6-14
Blood front and rear sensors detected partial
aspiration (<Tube ID>, <Cass/Pos,
Calibration factors received from analyzer
unexpectedly - delete runs & restart,
Carryover failed, 6-51
Carryover passed, 6-51
Cassette did not advance to next position,
Cassette Not Lowered Onto Bed,
CBC Bath Voltages Out Of Range,
CBC Xmit Failure, 6-15
Comment for control folder <lot#>, <comment>,
<comment>, 6-51
COMMON ROM AREA CRC ERROR,
Communication error with AMC or
interconnect, 6-8
Communication failure during transmission to
diluter, 6-22
Communications error, 6-8,
Compressor +48V Bad,
Compressor Too Hot,
Control Folder <Lot #> is expired (<Expiration
Date>), 6-51
Control folder <lot#> created, it must be edited in a
system setup for valid flagging,
Control folder for lot number <lot # created,
PN 773023AC
6-12
6-12
6-49
6-49
6-50
6-50
6-50
6-13
6-13
6-14
6-12
6-51
6-42
6-15
6-15
6-16
6-9
6-15
6-16
6-51
6-51
Control folder for lot number <lot #> deleted,
Control folder for lot number <lot #>edited,
Control lot is Inactive, Sample will be stored as a
Patient Sample, 6-52
Control run for control folder exceeds Extended
QC Random Error Limits for
parameter(s), 6-52
Control run for control folder exceeds Extended
QC Total Error Limits for parameter(s), 6-52
Control run for control folder <Lot #> out of
range, 6-53
Control run outside limits condition has
cleared, 6-53
CRC Error, 6-16
Daily check precision test failed,
Daily check ramp test failed,
Demographic information updated for, 6-54
Diagnostic Mode, 6-17
Did not detect rocker bed backward position,
Did not detect rocker bed forward position,
Did not detect rocker bed horizontal position,
Diff communication failure,
DIFF heater defective or disconnected,
Diff Heater Disabled, 6-17
Diff heater disabled for current cycle,
Diff Heater Sensor Bad, 6-17
Diff Laser Offset Lower Failed,
Diff Laser Offset Upper Failed,
Diff PC Communication Failed,
Diff Pressure Lower Failed,
Diff Pressure Upper Failed,
DIFF processor communication failure,
Diff Processor Does Not Answer,
DIFF Processor monitor command did not
finish, 6-33
Diff Processor Out Of Synch,
DIFF PS Card +15 V Error,
DIFF PS Card -15 V Error,
Diff RAM Test Failed, 6-19
DIFF sample pressure above limit (<Tube ID>,
<Cass/Pos>), 6-18
DIFF sample pressure below limit (<Tube ID>,
<Cass/Pos>), 6-18
DIFF timer error, 6-19
Diff Timer Test Failed, 6-19
DIFF Xmit Failure, 6-19
Dil SOL/OP PS +15V Error,
Dil SOL/OP PS -15V Error,
Dil SOL/OP PS 24V Error,
Dil1 Card +15V Error, 6-20
INDEX
6-51
6-51
6-53
6-53
6-13
6-14
6-14
6-17
6-17
6-17
6-17
6-17
6-17
6-18
6-18
6-18
6-18
6-18
6-18
6-19
6-19
6-20
6-20
INDEX-7