D-Link xStack DGS-3420 Series Reference Manual page 590

Layer 2 managed stackable gigabit switch cli
Hide thumbs Also See for xStack DGS-3420 Series:
Table of Contents

Advertisement

xStack® DGS-3420 Series Layer 2 Managed Stackable Gigabit Switch CLI Reference Guide
admin_status - Select the desired administrative per port state. The default per port state is
tx_and_rx.
tx_only - Configure the specified port(s) to transmit LLDP packets, but block inbound LLDP
packets from neighbor devices.
rx_only - Configure the specified port(s) to receive LLDP packets from neighbors, but block
outbound packets to neighbors.
tx_and_rx - Configure the specified port(s) to both transmit and receive LLDP packets.
disable - Disable LLDP packet transmit and receive on the specified port(s).
mgt_address - The port types specified for advertising indicated management address instance.
ipv4 - Specify the IP address of IPv4.
<ipaddr> - Specify the IP address of IPv4.
ipv6 - Specify the IP address of IPv6.
<ipv6addr> - Specify the IP address of IPv6.
enable - Enable port(s) specified for advertising indicated management address instance.
disable - Disable port(s) specified for advertising indicated management address instance.
basic_tlvs - Configure an individual port or group of ports to exclude one or more of optional TLV
data types from outbound LLDP advertisements.
all - (Optional) Configure all four TLV data types listed below.
port_description - (Optional) This TLV optional data type indicates that LLDP agent should
transmit "Port Description TLV" on the port. The default state is disabled.
system_name - (Optional) This TLV optional data type includes indicates that LLDP agent should
transmit "System Name TLV." The default state is disabled.
system_description - (Optional) This TLV optional data type includes indicates that LLDP agent
should transmit "System Description TLV." The default state is disabled.
system_capabilities - (Optional) This TLV optional data type includes indicates that LLDP agent
should transmit "System Capabilities TLV." The system capability will indicate whether the
device provides repeater, bridge, or router function, and whether the provided functions are
currently enabled. The default state is disabled.
enable - Enable configuration of an individual port or group of ports to exclude one or more of
optional TLV data types from outbound LLDP advertisements.
disable - Disable configuration of an individual port or group of ports to exclude one or more of
optional TLV data types from outbound LLDP advertisements.
dot1_tlv_pvid - This TLV optional data type determines whether the IEEE 802.1 organizationally
defined port VLAN ID TLV transmission is allowed on a given LLDP transmission capable port.
The default state is disabled.
enable - Enable port VLAN ID TLV transmission on a given LLDP transmission capable port.
disable - Disable port VLAN ID TLV transmission on a given LLDP transmission capable port.
dot1_tlv_protocol_vid - This TLV optional data type determines whether the IEEE 802.1
organizationally defined port and protocol VLAN ID TLV transmission is allowed on a given LLDP
transmission capable port. The default state is disabled.
vlan - (Optional) Specify a VLAN to be transmitted.
all - (Optional) Specify that all VLAN names will be transmitted.
<vlan_name 32> - (Optional) Specify a VLAN name to be transmitted.
vlanid - (Optional) Specify a VLAN ID list to be transmitted.
<vidlist> - Specify a VLAN ID list to be transmitted.
enable - Enable configuration of an individual port or group of ports to exclude one or more of
IEEE 802.1 Organizationally port and protocol VLAN ID TLV data types from outbound LLDP
advertisements.
disable - Disable configuration of an individual port or group of ports to exclude one or more of
IEEE 802.1 Organizationally port and protocol VLAN ID TLV data types from outbound LLDP
advertisements.
dot1_tlv_vlan_name - This TLV optional data type indicates whether the corresponding Local
System's VLAN name instance will be transmitted on the port. If a port is associated with multiple
VLANs, those enabled VLAN ID will be advertised. The default state is disabled.
vlan - (Optional) Specify a VLAN to be transmitted.
585

Advertisement

Table of Contents
loading

Table of Contents