Kyocera 300ci Service Manual page 431

Connector Pin No.
YC1 1
Connected 2
to the paper
feed clutch 2
YC2 1
Connected 2
to the paper
3
conveying
4
motor
5
6
7
8
YC3 1
Connected 2
to the lift
3
motor 1/2
4
5
6
7
8
9
10
YC4 1
Connected 2
to the lift
3
switch 1/2
4
and paper
switch 1/2
5
6
7
8
9
10
11
12
YC5 1
Connected 2
to the paper
feed clutch 1
YC6 1
Connected 2
to the
3
engine PWB
4
5
6
7
8
Signal I/O
+24V2 O
FED2 CLT REM O
+24V2 O
+24V2 O
PGND -
PGND -
FEED MT RDY I
FEED MT DR O
FEED MT DIR O
FEED MT CLK O
LFT1 MOT SIG2 I
PGND -
LFT1 MOT SIG1 I
LFT1 MOT DR2 O
LFT1 MOT DR1 O
LFT2 MOT SIG2 I
PGND -
LFT2 MOT SIG1 I
LFT2 MOT DR2 O
LFT2 MOT DR1 O
+5V1 O
CAS1 LFT UP I
GND -
+5V1 O
CAS1 EMPTY I
GND -
+5V1 O
CAS2 LFT UP I
GND -
+5V1 O
CAS2 EMPTY I
GND -
+24V2 O
FED1 CLT REM O
+24V2 I
+24V2 I
+24V2 I
PGND -
PGND -
PGND -
PGND -
+5V1 I
Voltage
24 V DC 24 V DC power to PFCL2
0/24 V DC PFCL2: On/Off
24 V DC 24 V DC power to PCM
24 V DC 24 V DC power to PCM
- Ground
- Ground
0/3.3 V DC PCM ready signal
0/3.3 V DC PCM: On/Off
0/3.3 V DC PCM drive switch signal
0/3.3 V DC (pulse) PCM clock signal
0/3.3 V DC LM1 paper gauge signal
- Ground
0/3.3 V DC LM1 paper gauge signal
0/24 V DC LM1 drive control signal
0/24 V DC LM1 drive control signal
0/3.3 V DC LM2 paper gauge signal
- Ground
0/3.3 V DC LM2 paper gauge signal
0/24 V DC LM2 drive control signal
0/24 V DC LM2 drive control signal
5 V DC 5 V DC power to LSW1
0/3.3 V DC LSW1: On/Off
- Ground
5 V DC 5 V DC power to PSW1
0/3.3 V DC PSW1: On/Off
- Ground
5 V DC 5 V DC power to LSW2
0/3.3 V DC LSW2: On/Off
- Ground
5 V DC 5 V DC power to PSW2
0/3.3 V DC PSW2: On/Off
- Ground
24 V DC 24 V DC power to PFCL1
0/24 V DC PFCL2: On/Off
24 V DC 24 V DC power from EPWB
24 V DC 24 V DC power from EPWB
24 V DC 24 V DC power from EPWB
- Ground
- Ground
- Ground
- Ground
5 V DC 5 V DC power from EPWB
2JZ/2JX/2JV/2H7
Description
2-3-43