Page 1 OCTANE2 ™ Workstation Owner’s Guide Document Number 007-4207-001...
Page 2 Contractor/manufacturer is Silicon Graphics, Inc., 2011 N. Shoreline Blvd., Mountain View, CA 94043-1389. Silicon Graphics, IRIS, and IRIX are registered trademarks and SGI, the SGI logo, OCTANE2, VPro, IRIX Interactive Desktop, Power Fortran Accelerator, IRIS InSight, and StereoView are trademarks of Silicon Graphics, Inc. ADAT is a registered trademark of Alesis Corporation.
Page 3 For regulatory and compliance information, go to Appendix C. OCTANE2 ™ Workstation Owner’s Guide Document Number 007-4207-001...
Page 4 OCTANE2 ™ Workstation Owner’s Guide Document Number 007-4207-001...
Page 5: Table Of Contents
Organizing Your Setup Process 7 Installing Optional Components 7 Setting Up the Octane2 Workstation 8 Locking the Octane2 Workstation 18 Logging In to the Octane2 Workstation 21 Using the IRIX Interactive Desktop 22 The IRIX Interactive Desktop and Its Icons 22 The Toolchest 23...
Page 6 Contents Shutting Down and Powering Off the Octane2 Workstation 25 Using the Power Button to Shut Down and Power Off 25 Using the Toolchest to Shut Down 27 Using the Toolchest to Restart 29 Installing and Removing the CPU and Memory 31...
Page 7 Removing a PCI Board 89 Opening the I/O Door for Extra-Long Connectors 94 Installing the PCI Module 100 Powering On the Octane2 Workstation 104 Verifying the PCI Board Installation 105 Installing and Removing XIO Boards 107 About the XIO Tri-Module and XIO Boards 108...
Page 8 Contents Powering On the Octane2 Workstation 142 Testing an External Device 143 Cleaning DAT or DLT Drives 146 Formatting a Floppy Disk from an External Drive 146 Installing Serial Devices 147 About Serial Ports 147 Installing the Serial Device 148...
Page 9 Removing and Replacing the Top Cover 190 Removing and Installing the Base 192 Reinstalling the Bezel 195 Reinstalling the Lockbar 196 Powering On the Octane2 Workstation 197 Troubleshooting 199 Using the LEDs on the Lightbar 199 Using the NMI Button 203...
Page 10 Contents Technical Speciﬁcations 221 Port Pinout Assignments 221 Audio Ports 222 Microphone Port 222 Speaker Port Pinout 223 Analog Line Level Port Pinout 224 Coaxial Digital Port Pinout 224 Optical Digital Port Pinout 225 SCSI Port 226 Ethernet 10-Base-T/100-Base-T Port 228 Parallel Port 229 Keyboard and Mouse Ports 230 Serial Ports 231...
Page 11 Contents Class A 249 Electromagnetic Emissions 250 Radio and Television Interference 251 Shielded Cables 252 Electrostatic Discharge 252 Class B 253 Electromagnetic Emissions 254 Shielded Cables 255 Electrostatic Discharge 255 Glossary 257 Index 275...
Page 13: List Of Figures
List of Figures Front View of the Octane2 Workstation 3 Figure 1-1 Back View of the Octane2 Workstation 4 Figure 1-2 Octane2 Components 5 Figure 1-3 Lifting the Octane2 Workstation 6 Figure 1-4 Attaching the Keyboard and Mouse Cables 8...
Page 14 System Shutdown Notifier 30 Figure 1-30 Power Off/Restart Notifier 30 Figure 1-31 Restart Notifier 30 Figure 1-32 Powering Off the Octane2 Workstation 32 Figure 2-1 Removing the Lockbar 33 Figure 2-2 Removing the Cables from the System Module 34 Figure 2-3...
Page 15 List of Figures Installing the Lockbar 59 Figure 2-28 Powering Off the Octane2 Workstation 62 Figure 3-1 Unplugging the Power Cable 63 Figure 3-2 Loosening the Power Supply Screws 64 Figure 3-3 Removing the Power Supply 65 Figure 3-4 Plugging In the Power Cable 66...
Page 16 Replacing the Power Cord and Turning On the Workstation 104 Figure 4-53 Locating the XIO Tri-Module 108 Figure 5-1 XIO Tri-Module with VPro Graphics Board I/O Ports 109 Figure 5-2 Powering Off the Octane2 Workstation 110 Figure 5-3 Removing the Monitor Cable 111 Figure 5-4...
Page 17 Using the Correct Cables between Devices and/or the Octane2 Figure 6-4 Workstation 137 Comparing Speed of Daisy-Chained Devices 138 Figure 6-5 Connecting an External SCSI Device to the Octane2 Workstation 139 Figure 6-6 Daisy-Chaining an External SCSI Device to Another External SCSI Figure 6-7 Device 140...
Page 18 Powering On the Octane2 Workstation 157 Figure 6-20 Powering Off the Octane2 Workstation and Monitor 161 Figure 7-1 Locating the Lockbar on the Front of the Octane2 Workstation 162 Figure 7-2 Unlocking and Removing the Lockbar 163 Figure 7-3 Pressing the Bezel Release Buttons 163...
Page 19 Replacing the Lockbar 196 Figure 7-37 Powering on the Octane2 Workstation 197 Figure 7-38 Lightbar LEDs - Front of Octane2, Diagnostic Chart #1 200 Figure 8-1 Lightbar LEDs - Front of Octane2, Diagnostic Chart #2 201 Figure 8-2 Lightbar LEDs - Front of Octane2, Diagnostic Chart #3 202...
Page 21: List Of Tables
List of Tables Comparison of Ultra and Fast, Wide and Narrow SCSI Rates 130 Table 6-1 Bus Rate + Operating Mode = Data Burst Rates 130 Table 6-2 Maximum Combined Cable Length 134 Table 6-3 Additional References on External SCSI Devices 145 Table 6-4 Serial Port Assignment 148 Table 6-5...
Page 22 List of Tables Headphone Specifications 244 Table B-23 Analog Line Level Specifications 244 Table B-24 PCI Module Power Specifications 244 Table B-25 FCC Declaration of Conformance 249 Table C-1 FCC Declaration of Conformance 253 Table C-2 xxii...
Page 23: About This Guide
About This Guide Welcome to the Silicon Graphics OCTANE2 workstation with VPro graphics! The Octane2 workstation provides you with dramatically fast state-of-the art graphics capabilities and massive computer power in a desktop system. With a crossbar-based symmetric multiprocessing architecture, the Octane2 workstation allows you to visualize and manipulate three-dimensional images, simulate large data sets, interact with three-dimensional models, and perform many other advanced functions.
Page 24: Software And System Administration Information
About This Guide This guide is provided for all Octane2 users and SGI technical support staff. Most of the hardware tasks are relatively simple and require no previous computer knowledge. A few tasks are lengthy; they are easier to perform if you have some computer hardware experience.
Page 25 Call the Technical Publications Group through the Technical Assistance Center at 1.800.800.4SGI. • Send mail to: Technical Publications, Silicon Graphics, Inc., 1600 Amphitheatre Pkwy., M/S 535, Mountain View, California, 94043-1351. We value your comments and will respond to them promptly.
Page 27: Getting Started
Chapter 1 Getting Started This chapter shows you how to set up your Octane2 workstation. The following topics are covered: • “Getting Acquainted” on page 1 • “Lifting the Octane2 Workstation” on page 6 • “Installing Optional Components” on page 7 •...
Page 28 Octane2 Hardware Central (You cannot access Octane2 Hardware Central from the Online Books path). If Octane2 Hardware Central is not currently installed on your system disk, reinstall it as follows: 1. Place the IRIX 6.5 Foundation 2 CD in your CD-ROM drive, or access it over the network.
Page 29: Front View
Getting Acquainted Front View Bezel release buttons Bezel with door Option drive bays Power button Ventilation grid Reset button Light Figure 1-1 Front View of the Octane2 Workstation...
Page 30: Back View
In Out Optical digital audio - in Serial number Optical digital audio - out XIO boards (graphics and communications) SCSI PCI module Ethernet Parallel Mouse Keyboard Power supply Serial ports Power cable Figure 1-2 Back View of the Octane2 Workstation...
Page 31: Checking Your Shipment
Getting Acquainted Checking Your Shipment Documentation Compression Octane2 connector caps Monitor Mouse Wriststrap Microphone Keyboard Lockbar Speakers Power cables - 10 ft Speaker/workstation Monitor cable - 10 ft cable - 10 ft Octane2 Components Figure 1-3...
Page 32: Lifting The Octane2 Workstation
Chapter 1: Getting Started Lifting the Octane2 Workstation Lifting the Octane2 workstation requires two people. Lift the workstation by the air vents at the top of the chassis, as shown in Figure 1-4. Figure 1-4 Lifting the Octane2 Workstation...
Page 33: Organizing Your Setup Process
Organizing Your Setup Process If you have no additional components, memory, or peripherals to install, use the setup poster or the setup procedures (starting on page 8) to set up your Octane2 workstation. Installing Optional Components If you have optional components or peripherals, install them before you follow the setup procedures, so you do not have to remove and reinstall cables.
Page 34: Setting Up The Octane2 Workstation
Chapter 1: Getting Started Setting Up the Octane2 Workstation Human factors guidelines for setting up your Octane2 workstation are in Octane2 Hardware Central. You can access this information by choosing Toolchest > Help > Online Books > SGI End User.
Page 35: Figure 1-6 Attaching The Ethernet Cable
Setting Up the Octane2 Workstation 2. Attach the Ethernet cable to the Ethernet port, as shown in Figure 1-6. Ethernet Figure 1-6 Attaching the Ethernet Cable...
Page 36: Figure 1-7 Attaching The Speaker-To-Speaker Cable
Chapter 1: Getting Started 3. Place the speakers on either side of the monitor, as shown in Figure 1-7. 4. Connect the left (passive) speaker to the right (active) speaker. Use the port labeled L. Left (passive) speaker Right (active) speaker Power Figure 1-7 Attaching the Speaker-to-Speaker Cable...
Page 37: Figure 1-8 Attaching The Speaker And Power Cable To The Active Speaker
Setting Up the Octane2 Workstation 5. Connect the speaker/workstation cables (the cable with two connectors on each end) to the active speaker, as shown in Figure 1-8. The connectors cannot be installed incorrectly because they are different sizes: male/male on one end, female/male on the other.
Page 38: Figure 1-9 Connecting The Speaker And Power Cables
Chapter 1: Getting Started 6. Connect the active speaker to your workstation, using the cable with two male connectors on the end, as shown in Figure 1-9. Connect the smaller male connector to the speaker power port. Attach the larger male connector to the speaker port. Speaker Power Connecting the Speaker and Power Cables...
Page 39: Figure 1-10 Attaching The Microphone
Setting Up the Octane2 Workstation 7. Set up the microphone, as shown in Figure 1-10. Place the microphone cord through the slot in the microphone base. Slide the microphone back until it is ﬁrmly connected to its base. Place the microphone and base on the center-top area of the monitor.
Page 40: Figure 1-11 Connecting The Monitor And Power Cables
Connect the monitor-to-graphics cable (B) to the monitor connector on the back of your workstation. Connect the monitor power cable (C) to the monitor. Connect the Octane2 power cable (D) to the back of your workstation. Figure 1-11 Connecting the Monitor and Power Cables...
Page 41: Figure 1-12 Connecting The Monitor And Power Cables To An Electrical Outlet
Setting Up the Octane2 Workstation 9. Connect the power cables from your workstation and monitor to an electrical outlet, as shown in Figure 1-12. Figure 1-12 Connecting the Monitor and Power Cables to an Electrical Outlet...
Page 42: Figure 1-13 Powering On The Monitor
11. Press the power button on the active speaker, as shown in Figure 1-14. If you are installing the lockbar, see “Locking the Octane2 Workstation” on page 18. If you are not installing the lockbar, proceed to the next step.
Page 43 12. Press the power button on your workstation, as shown in Figure 1-15. Power button Figure 1-15 Powering On the Octane2 Workstation You just completed your workstation setup. Now you are ready to log in. See “Logging In to the Octane2 Workstation” on page 21.
Page 44: Locking The Octane2 Workstation
Chapter 1: Getting Started Locking the Octane2 Workstation The lockbar locks the bezel and system module to the chassis. Locking the bezel prevents the option and system drives from being removed. Locking the system module prevents the memory (DIMMs) and processor (CPU) from being removed.
Page 45: Figure 1-17 Inserting The Lockbar
Locking the Octane2 Workstation 3. Slide in the lockbar (A), as shown in Figure 1-17. 4. Secure it with a lock (B). 5. Close the door. Push in Figure 1-17 Inserting the Lockbar...
Page 46 Chapter 1: Getting Started 6. Power on your workstation, as shown in Figure 1-18. Power button Figure 1-18 Powering On the Octane2 Workstation You just completed your workstation setup. Now you are ready to log in.
Page 47: Logging In To The Octane2 Workstation
Logging In to the Octane2 Workstation Logging In to the Octane2 Workstation If your system is booting for the ﬁrst time, you see a login screen similar to the example shown in Figure 1-19. Figure 1-19 Login Screen If you have a login account, an icon with your login name appears. Double-click the icon.
Page 48: Using The Irix Interactive Desktop
Chapter 1: Getting Started Using the IRIX Interactive Desktop Now you are ready to use the IRIX Interactive Desktop. The IRIX Interactive Desktop and Its Icons By default, several icons appear on your desktop: a folder icon representing your home directory, a dumpster icon, and icons for any peripherals you installed, as shown in the examples in Figure 1-20.
Page 49: The Toolchest
Click Toolchest > Help > InfoSearch and type the name of the desired book or topic to search online books, man pages, and release notes that cover end user, developer, and system administrator information. With InfoSearch, you can also access Octane2 Hardware Central and the online version of this guide, as described earlier in this chapter.
Page 50: The Console Window
Chapter 1: Getting Started The Console Window The small box next to the Toolchest is the Console window, as shown in Figure 1-22. It appears as a small box because it is minimized. You can open it to its full size by clicking it.
Page 51: Shutting Down And Powering Off The Octane2 Workstation
Shutting Down and Powering Off the Octane2 Workstation Shutting Down and Powering Off the Octane2 Workstation There are two ways to shut down and power off your workstation: • Press the power button to shut down the system software and power off.
Page 52: Figure 1-24 System Shutdown Notifier
Chapter 1: Getting Started Within a few seconds, a shutdown notiﬁer appears, as shown in Figure 1-24. Within a minute, the system powers off automatically. Figure 1-24 System Shutdown Notiﬁer 3. Turn off your monitor by pressing the monitor power button. If your system does not power off and you do not see any activity for several minutes, follow the next step.
Page 53: Using The Toolchest To Shut Down
Shutting Down and Powering Off the Octane2 Workstation Using the Toolchest to Shut Down If you are logged in with your root password, you can use the System menu in the Toolchest to shut down your system. 1. Choose Toolchest > System > System Shutdown.
Page 54: Figure 1-27 Restart System Option
Chapter 1: Getting Started 2. Click the Power Off the System check box. The Restart the system option appears. At this point, you can shut down and power off the system or restart it at the designated time, as shown in Figure 1-27. Figure 1-27 Restart System Option 3.
Page 55: Using The Toolchest To Restart
Shutting Down and Powering Off the Octane2 Workstation Using the Toolchest to Restart If you are logged in with your root password, you can use the System menu in the Toolchest to restart. 1. Choose Toolchest > System > Restart.
Page 56: Figure 1-30 System Shutdown Notifier
Chapter 1: Getting Started 2. Click OK in the restart notiﬁer. The shutdown notiﬁer appears, as shown in Figure 1-30. Figure 1-30 System Shutdown Notiﬁer After a brief delay, the power off/restart notiﬁer appears, as shown in Figure 1-31. Figure 1-31 Power Off/Restart Notiﬁer 3.
Page 57: Installing And Removing The Cpu And Memory
“Removing and Replacing the CPU” on page 41 • “Installing and Removing Memory” on page 47 • “Reinstalling the System Module” on page 53 • “Powering On the Octane2 Workstation” on page 58 • “Verifying Memory Installation” on page 60...
Page 58: Preparing The Workstation
Power button Power cable Power switch Figure 2-1 Powering Off the Octane2 Workstation Warning: The heat sinks on the CPU and system module get very hot. Wait 5 minutes after powering off your workstation before you remove the system module. Test before touching the CPU or heat sinks.
Page 59: Figure 2-2 Removing The Lockbar
Preparing the Workstation 4. If your system has a lockbar installed remove it (a lockbar locks the system module and bezel to the chassis). Unlock the lock (see A in Figure 2-2) at the back of your workstation. Pull the lockbar (B) out of your workstation. Figure 2-2 Removing the Lockbar...
Page 60: Figure 2-3 Removing The Cables From The System Module
Chapter 2: Installing and Removing the CPU and Memory 5. Face the rear of your workstation. 6. Remove the cables attached to the system module, as shown in Figure 2-3. For illustration purposes, the optional PCI module is shown installed. For a Note: description of the PCI module, go to Chapter 4, “Installing and Removing PCI Boards.”...
Page 61: Attaching The Wrist Strap
Attaching the Wrist Strap Attaching the Wrist Strap Caution: The components inside your workstation are extremely sensitive to static electricity. Always wear the wrist strap when you replace parts inside your workstation. 1. Unroll the ﬁrst two folds of the band (see A in Figure 2-4). 2.
Page 62: Removing The System Module
Chapter 2: Installing and Removing the CPU and Memory Removing the System Module 1. Use the provided Phillips screwdriver to loosen the two captive screws that secure the sliding handles to the workstation, as shown in Figure 2-5. Figure 2-5 Loosening the System Module Screws The heat sinks on the CPU and system module get very hot.
Page 63: Figure 2-6 Releasing The System Module From The Frontplane
Removing the System Module After powering off your workstation, attaching the wrist strap, and waiting ﬁve minutes for the heat sinks to cool, you can remove the system module. 2. Pull both sliding handles simultaneously until they are completely extended, as shown in Figure 2-6.
Page 64: Figure 2-7 Removing The System Module From The Chassis
Chapter 2: Installing and Removing the CPU and Memory 3. Pull the system module from the chassis by grasping the immovable handle with your left hand and bracing your right hand against the top of the workstation, as shown in Figure 2-7. Support the bottom of the module as you pull it out.
Page 65: Figure 2-8 Locating The Compression Connectors
Removing the System Module Caution: When you remove the system module from the chassis, do not touch the two compression connectors at the back of the system module, as shown in Figure 2-8. The gold bristled pad on each compression connector is very delicate and easily damaged (see Figure 2-9).
Page 66: Figure 2-10 Placing The Compression Cap On The Compression Connector
Chapter 2: Installing and Removing the CPU and Memory 5. Place a cap on each compression connector on the back of the system module, as shown in Figure 2-10 (compression connector caps are included with your workstation.) Caution - Do not touch Figure 2-10 Placing the Compression Cap on the Compression Connector The heat sinks on the CPU and system module get very hot.
Page 67: Removing And Replacing The Cpu
Removing and Replacing the CPU Removing and Replacing the CPU Your workstation has either a single CPU or a dual CPU installed. Following are instructions for removing and replacing each type of CPU. Follow the same instructions for CPUs of different speeds. Removing the CPU To remove a CPU, power off your workstation, wait 5 minutes to allow the heat sinks to cool, and attach the wrist strap.
Page 68: Figure 2-12 Lifting A Single Processor From The System Module
Chapter 2: Installing and Removing the CPU and Memory 2. To release a single processor, slide your ﬁngers under its edge closest to the back of the module, then push up to release it, as shown in Figure 2-12. You may need to use two hands to lift it out.
Page 69: Figure 2-13 Lifting A Dual Processor From The System Module
Removing and Replacing the CPU If you have a dual processor, slide your ﬁngers under the side bar of the system module and under the processor, then push up to release it, as shown in Figure 2-13. After releasing the dual processor, lift it out of the system module. Dual processor Lifting a Dual Processor from the System Module Figure 2-13...
Page 70: Replacing The Cpu/Processor
Chapter 2: Installing and Removing the CPU and Memory Replacing the CPU/Processor To install a new CPU, power off your workstation, wait 5 minutes to allow the heat sinks to cool, and attach the wriststrap. Then remove the system module and the currently installed CPU, as described earlier in this chapter, and follow these steps: 1.
Page 71: Figure 2-15 Installing A Single Processor
Removing and Replacing the CPU 3. If you are installing a single processor, place it on the side of the system module closest to the panel of connectors, as shown in Figure 2-15. 4. Lower the CPU onto the standoffs and connectors. 5.
Page 72: Figure 2-16 Installing A Dual Processor
Chapter 2: Installing and Removing the CPU and Memory Figure 2-16 shows a dual processor installation. Dual processor Figure 2-16 Installing a Dual Processor You are ﬁnished replacing the CPU and are ready to reinstall the system module. Go to “Reinstalling the System Module” on page 53.
Page 73: Installing And Removing Memory
Handle the DIMMs carefully and wear the wrist strap to avoid the ﬂow of static electricity. About Memory The Octane2 workstation has four DIMM banks with two DIMM sockets in each of the banks. Before you install the two 1 GB DIMMs, review the following information: •...
Page 74: Figure 2-17 Identifying Dimm Sockets And Dimm Banks
Chapter 2: Installing and Removing the CPU and Memory Figure 2-17 shows the four Octane2 DIMM banks, with two DIMM sockets in each bank. Heat sink Banks System module DIMM sockets Figure 2-17 Identifying DIMM Sockets and DIMM Banks...
Page 75: Locating The Dimms On The System Module
Installing and Removing Memory Locating the DIMMs on the System Module If you did not power off your workstation, wait 5 minutes to allow the heat sinks to cool, attach the wrist strap, and remove the system module, follow the instructions for preparing your workstation beginning on page 32.
Page 76: Removing The Dimm Bracket
Chapter 2: Installing and Removing the CPU and Memory Removing the DIMM Bracket If a DIMM bracket is not installed (see Figure 2-18), skip this section. If a DIMM bracket is installed, as shown in Figure 2-19, you must remove it as follows: 1.
Page 77: Removing Memory
Installing and Removing Memory Removing Memory Memory modules are extremely sensitive to static electricity. Handle the modules carefully, and wear the wrist strap while removing them. 1. Locate the DIMMs you want to remove. Caution: Do not touch the connector near the DIMM removal levers. 2.
Page 78: Installing Memory
Chapter 2: Installing and Removing the CPU and Memory Installing Memory If you did not power off your workstation, wait 5 minutes to allow the heat sinks to cool, attach the wrist strap, and remove the system module, follow the instructions for preparing your workstation beginning on page 36.
Page 79: Reinstalling The System Module
Caution: Do not insert the system module into the workstation unless the power cable is unplugged from the electrical socket. If you insert the system module into the Octane2 workstation with the power cable connected to an electrical socket, the workstation will be damaged.
Page 80: Figure 2-23 Supporting The System Module
Chapter 2: Installing and Removing the CPU and Memory 2. Grasp the system module by its immovable handle and support it with one hand as you slide it into the chassis, as shown in Figure 2-23. Then push the system module completely into the chassis (both sliding handles protrude).
Page 81: Figure 2-24 Locking The System Module To The Frontplane
Reinstalling the System Module 3. Push both sliding handles simultaneously to connect the system module to the workstation, as shown in Figure 2-24. Then push ﬁrmly on the sliding handles to completely lock the system module to the workstation. The system module is fully seated and locked to the workstation when it is ﬂush with the chassis and the sliding handles are completely recessed.
Page 82: Figure 2-25 Tightening The System Module Screws
Chapter 2: Installing and Removing the CPU and Memory 4. Tighten the captive screws in the sliding handles until the system module is attached to the chassis, as shown in Figure 2-25. Figure 2-25 Tightening the System Module Screws 5. Remove the wrist strap.
Page 83: Figure 2-26 Reconnecting Cables To The System Module
Reinstalling the System Module 6. Reconnect any cables you removed, as shown in the example in Figure 2-26. Figure 2-26 Reconnecting Cables to the System Module...
Page 84: Powering On The Octane2 Workstation
Chapter 2: Installing and Removing the CPU and Memory Powering On the Octane2 Workstation 1. Plug in the power cable (see A in Figure 2-27). 2. Press the power button (B) on your workstation. 3. Press the monitor power button (C) to turn on your monitor.
Page 85: Figure 2-28 Installing The Lockbar
Powering On the Octane2 Workstation 4. Replace the lockbar. Open the cover on the front of your workstation. Slide the lockbar into the lockbar slot (see A in Figure 2-28). Insert the lock (B) through the lockbar at the back of your workstation.
Page 86: Verifying Memory Installation
Chapter 2: Installing and Removing the CPU and Memory Verifying Memory Installation 1. After you power on your system, choose Toolchest > System Manager > Hardware and Devices > About This System and check the amount of memory displayed for Main Memory.
Page 87: Installing And Removing The Power Supply
Chapter 3 Installing and Removing the Power Supply This chapter shows you how to remove and replace the Octane2 power supply, which is located at the bottom of your workstation. The following topics are covered: • “Preparing the Workstation” on page 62 •...
Page 88: Preparing The Workstation
1. Open the cover and press the power button (see A in Figure 3-1) to power off your workstation. 2. Unplug the power cable (B) from the electrical socket. 3. Press the monitor power switch (C) to power off your monitor. Power button Power cable Power switch Powering Off the Octane2 Workstation Figure 3-1...
Page 89: Figure 3-2 Unplugging The Power Cable
Preparing the Workstation 4. Face the back of your workstation. 5. Unplug the power cable from your workstation (power supply), as shown in Figure 3-2. Before proceeding to the next section, wait until the power supply fan stops spinning and you cannot feel any air coming out of the power supply. Power supply Unplugging the Power Cable Figure 3-2...
Page 90: Removing The Pci Module
Chapter 3: Installing and Removing the Power Supply Removing the PCI Module If a PCI module is not installed in your workstation, go to the next section. If a PCI module is installed in your workstation, you must remove it before you remove the power supply.
Page 91: Figure 3-4 Removing The Power Supply
Removing the Power Supply 3. Grasp the handle and pull the power supply from the chassis, as shown in Figure 3-4. Figure 3-4 Removing the Power Supply...
Page 92: Installing The Power Supply
Chapter 3: Installing and Removing the Power Supply Installing the Power Supply Follow these steps to install the new power supply: 1. Tilt the new power supply upward and plug the power cable into the power supply, as shown in Figure 3-5. Figure 3-5 Plugging In the Power Cable 2.
Page 93: Figure 3-7 Inserting And Tightening The Screws
For instructions on reinstalling the PCI module, go to “Installing the PCI Module” on page 100, and follow the instructions through powering on the Octane2 workstation. If you are not reinstalling a PCI module, you are ready to power on your workstation, as...
Page 94: Powering On The Octane2 Workstation
Chapter 3: Installing and Removing the Power Supply Powering On the Octane2 Workstation 1. Plug the power cable into an electrical outlet (see A in Figure 3-8). 2. Press the power button (B) on your workstation. 3. Press the monitor power button (C) to turn on your monitor.
Page 95: Installing And Removing Pci Boards
Chapter 4 Installing and Removing PCI Boards This chapter shows you how to install and remove PCI boards. The following topics are covered: • “About the PCI Module and Boards” on page 70 • “Preparing the Workstation” on page 72 •...
Page 96: About The Pci Module And Boards
To install PCI boards, you must use the PCI module. The PCI module is an optional Octane2 component that allows you to install and remove PCI boards without opening your workstation. If your workstation does not have a PCI module installed, a blank panel covers the module slot, as shown in Figure 4-1.
Page 97: Figure 4-2 Workstation With The Optional Pci Module
Figure 4-2 Workstation with the Optional PCI Module The Octane2 PCI module is a 5V system environment. Total power for the PCI module (the sum of the power for all installed PCI boards) must not exceed 45.0W (average 15.0W per board).
Page 98: Preparing The Workstation
1. Open the cover and press the power button (see A in Figure 4-3). 2. Unplug the power cable from the electrical outlet (B). 3. Press the monitor power switch to turn off your monitor (C). Power button Power cable Power switch Powering Off the Octane2 Workstation Figure 4-3...
Page 99: Figure 4-4 Removing The Cables From The Pci Module
Preparing the Workstation 4. Face the rear of your workstation. 5. Remove any cables from the PCI module, as shown in Figure 4-4. Figure 4-4 Removing the Cables from the PCI Module...
Page 100: Attaching The Wrist Strap
Chapter 4: Installing and Removing PCI Boards Attaching the Wrist Strap Caution: The components inside your workstation are extremely sensitive to static electricity; you must wear the wrist strap while replacing parts. 1. Unroll the ﬁrst two folds of the band (see A in Figure 4-5). 2.
Page 101: Removing The Pci Module
Removing the PCI Module Removing the PCI Module To install or remove PCI boards, you must remove the PCI module from the workstation. 1. Loosen the two captive screws that secure the PCI module to the workstation, as shown in Figure 4-6, until they are disconnected from the chassis. Figure 4-6 Removing the Screws From the PCI Module 2.
Page 102: Figure 4-8 Removing The Pci Module
Chapter 4: Installing and Removing PCI Boards 3. Remove the PCI module by sliding it out of the workstation, as shown in Figure 4-8, then place it on a dry, antistatic surface, such as your desk. Figure 4-8 Removing the PCI Module Caution: The compression connector on the back of the PCI module is delicate and easily damaged.
Page 103: Figure 4-10 Installing A Cap On The Compression Connector
Removing the PCI Module 4. Place a cap on the compression connector on the back of the PCI module, as shown in Figure 4-10 (compression connector caps are included with the workstation). Caution: Do not touch Installing a Cap on the Compression Connector Figure 4-10...
Page 104: Opening The Pci Module
Chapter 4: Installing and Removing PCI Boards Opening the PCI Module If you removed the PCI module from your workstation, go to step 1, below. If the PCI module is still installed in your workstation, go to “Preparing the Workstation” on page 72 and follow the instructions through removing the PCI module.
Page 105: Identifying A Pci Slot
Identifying a PCI Slot Identifying a PCI Slot PCI physical slots and PCI slots identiﬁed by the system software have the same identiﬁcation numbers (see Figure 4-13). • The top slot is PCI ID #1. • The middle slot is PCI ID #2. The bottom (half-sized) slot is PCI ID #3.
Page 106: Installing A Pci Board
Chapter 4: Installing and Removing PCI Boards Installing a PCI Board If you did not prepare your workstation for a PCI board installation, go to “Preparing the Workstation” on page 72 and follow the instructions through removing the PCI module. Then return to this page and follow these steps: Caution: PCI boards are extremely sensitive to static electricity: You must wear the wrist strap while removing or installing them.
Page 107: Figure 4-15 Removing The Blank I/O Panel
Installing a PCI Board Removing the Blank I/O Panel Figure 4-15 4. Insert the PCI board into the connector in the PCI module, as shown in Figure 4-16. Push gently but ﬁrmly until the PCI board snaps into place. If the board has an extra-long connector that makes it difﬁcult to insert, skip Note: to the next section, “Opening the I/O Door for Extra-Long Connectors”...
Page 108: Figure 4-17 Inserting The Board Screw
Chapter 4: Installing and Removing PCI Boards 5. Insert and tighten the screw that secures the PCI board to the PCI module, as shown in Figure 4-17. Figure 4-17 Inserting the Board Screw 6. Place the hinged door on the PCI module, as shown in Figure 4-18. Release hinge Placing the Door on the PCI Module Figure 4-18...
Page 109: Figure 4-19 Tightening The I/O Door Screws
Installing a PCI Board 7. Tighten the I/O door screws, as shown in Figure 4-19. Figure 4-19 Tightening the I/O Door Screws Go to “Installing the PCI Module” on page 100.
Page 110: Opening The I/O Door For Extra-Long Connectors
Chapter 4: Installing and Removing PCI Boards Opening the I/O Door for Extra-Long Connectors 1. If boards are installed in the PCI module, remove the I/O panel screws that secure the boards, as shown in Figure 4-20. Do not remove any blank I/O panels. They are attached to the door and move Note: with it.
Page 111: Figure 4-21 Removing The I/O Door Screws
Installing a PCI Board 2. Completely remove the screws that secure the I/O door to the PCI module, as shown in Figure 4-21. Removing the I/O Door Screws Figure 4-21 3. Slide open the I/O door to expand the PCI module, as shown in Figure 4-22. I/O door expansion device Figure 4-22 Opening the I/O Door...
Page 112: Figure 4-23 Inserting A Pci Board With An Extra-Long Connector
Chapter 4: Installing and Removing PCI Boards 4. Insert the PCI board into the connector in the PCI module, as shown in Figure 4-23. Press gently but ﬁrmly until the board snaps into place. Figure 4-23 Inserting a PCI Board with an Extra-long Connector 5.
Page 113: Figure 4-25 Reinstalling The I/O Door Screws
Installing a PCI Board 6. Insert and tighten the screws that secure the I/O door, as shown in Figure 4-25. Figure 4-25 Reinstalling the I/O Door Screws 7. Insert and tighten the screws that secure all PCI boards to the I/O panel, as shown in Figure 4-26.
Page 114: Figure 4-27 Reinstalling The Pci Module Door, As Shown In Figure
Chapter 4: Installing and Removing PCI Boards 8. Reinstall the PCI module door, as shown in Figure 4-27. Release hinge Figure 4-27 Reinstalling the PCI Module Door, as shown in Figure 4-28. 9. Tighten the PCI module door screws. Tightening the PCI Module Door Screws Figure 4-28 Go to “Installing the PCI Module”...
Page 115: Removing A Pci Board
Removing a PCI Board Removing a PCI Board If you did not prepare your workstation for removal of a PCI board, go to “Preparing the Workstation” on page 72, and follow the instructions through removing the PCI module. Then return to this page and follow these steps: 1.
Page 116: Figure 4-30 Extracting The Pci Board
Chapter 4: Installing and Removing PCI Boards 2. Grasp the PCI board on the top edge to extract it, as shown in Figure 4-30. 3. Pull up until the board releases. If the board is ﬁrmly installed, it may be hard to remove. If it is very hard to remove, go to “Opening the I/O Door for Extra-Long Connectors”...
Page 117: Figure 4-31 Inserting The I/O Door Screws
Removing a PCI Board 4. Insert, but do not tighten, the screws securing the I/O door to the PCI module, as shown in Figure 4-31. Inserting the I/O Door Screws Figure 4-31 5. Install an I/O blank panel in the I/O door in place of the PCI board, as shown in Figure 4-32.
Page 118: Figure 4-33 Attaching The Blank Panel To The I/O Door
Chapter 4: Installing and Removing PCI Boards 6. Attach the blank panel to the I/O door with the screw you removed in step 1, as shown in Figure 4-33. Figure 4-33 Attaching the Blank Panel to the I/O Door 7. Reinstall the PCI module door, as shown in Figure 4-34. Release hinge Figure 4-34 Reinstalling the PCI Module Door...
Page 119: Figure 4-35 Replacing The Screws Of The Pci Module Door
Removing a PCI Board 8. Tighten the door screws, as shown in Figure 4-35. Figure 4-35 Replacing the Screws of the PCI Module Door Go to “Installing the PCI Module” on page 100.
Page 120: Opening The I/O Door For Extra-Long Connectors
Chapter 4: Installing and Removing PCI Boards Opening the I/O Door for Extra-Long Connectors 1. Remove the screws that secure any other PCI boards to the module, as shown in Figure 4-36. Figure 4-36 Removing the I/O Panel Screws 2. Remove the screws that secure the I/O panel door to the PCI module, as shown in Figure 4-37.
Page 121: Figure 4-38 Opening The I/O Door
Removing a PCI Board 3. Slide open the I/O door, as shown in Figure 4-38. This provides clearance for the I/O connector at the end of the PCI board. Now you can easily remove the board. If two other boards are installed at the sides of the PCI module, you can now grasp their edges.
Page 122: Figure 4-39 Removing A Pci Board
Chapter 4: Installing and Removing PCI Boards 4. Grasp the PCI board on the top edge to extract it. 5. Pull up until the board releases, Figure 4-39. If the board is ﬁrmly installed, it may be difﬁcult to remove. If you want to install another PCI board, go to “Installing a PCI Board”...
Page 123: Figure 4-40 Closing The I/O Door
Removing a PCI Board 6. Close the I/O door, as shown in Figure 4-40. Figure 4-40 Closing the I/O Door 7. Insert, but do not tighten, the screws holding the I/O door to the PCI module, as shown in Figure 4-41. Figure 4-41 Inserting the I/O Door Screws...
Page 124: Figure 4-42 Inserting The I/O Blank Panel
Chapter 4: Installing and Removing PCI Boards 8. Install an I/O blank panel in the I/O door in place of the PCI board, as shown in Figure 4-42. Use the knobs on the back of the blank panel to position it. Make sure you place the tip of the I/O blank panel inside the groove at the bottom of the PCI module.
Page 125: Figure 4-44 Reinstalling The Pci Module Door
Removing a PCI Board 10. Reinstall the PCI module door, as shown in Figure 4-44. Release hinge Reinstalling the PCI Module Door Figure 4-44 11. Tighten the PCI module door screws, as shown in Figure 4-45. Tightening the PCI Module Door Screws Figure 4-45 Go to “Installing the PCI Module”...
Page 126: Installing The Pci Module
Chapter 4: Installing and Removing PCI Boards Installing the PCI Module If you are installing a PCI module for the ﬁrst time, you have to remove the blank panel. 1. Using a Phillips screwdriver, remove the screws from the blank panel, as shown in Figure 4-46.
Page 127: Figure 4-47 Removing The Blank Panel
Installing the PCI Module PCI blank panel Removing the Blank Panel Figure 4-47 4. Remove the cap from the compression connector on the back of the PCI module, and save it for future use, as shown in Figure 4-48. Caution - Do not touch Figure 4-48 Removing the Cap from the Compression Connector...
Page 128: Figure 4-49 Installing The Pci Module
Chapter 4: Installing and Removing PCI Boards 5. Insert the PCI module in your workstation, as shown in Figure 4-49, then push it until the tabs are ﬂush with the chassis. Figure 4-49 Installing the PCI Module 6. Close the release lever by pushing it to the left until it is parallel with the PCI module, as shown in Figure 4-50.
Page 129: Figure 4-51 Tightening The Pci Screws
8. Connect any PCI cables to the PCI connectors, as shown in Figure 4-52. Installing the PCI Cables Figure 4-52 9. Remove the wrist strap. You are ﬁnished installing the PCI module. Go to “Powering On the Octane2 Workstation” on page 104.
Page 130: Powering On The Octane2 Workstation
Chapter 4: Installing and Removing PCI Boards Powering On the Octane2 Workstation 1. Face the front of your workstation. 2. Connect the workstation’s power cable to an electrical outlet (see A in Figure 4-53). 3. Press the power button (B) to power on your workstation.
Page 131: Verifying The Pci Board Installation
Verifying the PCI Board Installation Verifying the PCI Board Installation For instructions on checking the PCI board installation, see the Octane2 PCI Module Installation Guide. 1. If your PCI board does not function properly, repeat the installation procedure. 2. If you repeat the installation procedure and your PCI board still does not function...
Page 133: Installing And Removing Xio Boards
This chapter describes the Octane2 XIO Tri-Module and shows you how to install and remove XIO option boards. In addition to the onboard VPro graphics, you can connect one or two XIO option boards to the Tri-Module, such as the Octane2 video option board or the Ultra SCSI option board.
Page 134: About The Xio Tri-Module And Xio Boards
The XIO Tri-Module is located on the right-rear side of your workstation, as shown in Figure 5-1. It is a tray-like holding mechanism for the Octane2 VPro graphics board and XIO option boards. You can connect up to three option boards to the XIO Tri-Module using slots A/B, C, and D.
Page 135: Figure 5-2 Xio Tri-Module With Vpro Graphics Board I/O Ports
About the XIO Tri-Module and XIO Boards Figure 5-2 shows the XIO Tri-Module and each of the VPro graphics board I/O ports. Genlock StereoView Swap Ready InOut Monitor (see note below) Figure 5-2 XIO Tri-Module with VPro Graphics Board I/O Ports For VPro graphics, a 1280 x 1024 display resolution is only possible using the Sony Note: G1 21”...
Page 136: Preparing The Workstation
Power button Power cable Power switch Figure 5-3 Powering Off the Octane2 Workstation The heat sinks on the XIO boards get very hot. Wait 5 minutes after Warning: powering off your workstation before you remove the XIO Tri-Module. Test before touching any of the XIO boards.
Page 137: Figure 5-4 Removing The Monitor Cable
Preparing the Workstation 5. Remove all the cables from the XIO Tri-Module (only one is shown in Figure Figure 5-4). To monitor Removing the Monitor Cable Figure 5-4...
Page 138: Attaching The Wrist Strap
Chapter 5: Installing and Removing XIO Boards Attaching the Wrist Strap Caution: The internal components are extremely sensitive to static electricity; always wear the wrist strap when you handle parts inside your workstation. To attach the wrist strap, follow these steps: 1.
Page 139: Compression Connector Caution
Preparing the Workstation Compression Connector Caution Caution: The compression connectors on all VPro graphics boards and most option boards are very delicate and easily damaged. Do not touch or bump the gold bristled pad shown in Figure 5-6. The connectors are on the side opposite the handles. Do not grab the back of the XIO Tri-Module when you remove it, or the compression connectors may be damaged.
Page 140: Removing The Xio Tri-Module
Chapter 5: Installing and Removing XIO Boards Removing the XIO Tri-Module Before removing the XIO Tri-Module, you must power off your workstation, wait 5 minutes to allow the heat sinks to cool, and attach the wrist strap. If you did not already do this, go to “Preparing the Workstation”...
Page 141: Figure 5-8 Releasing The Xio Tri-Module
Removing the XIO Tri-Module 2. Grasp the sliding handles and pull them until the sliding portion of the XIO Tri-Module protrudes about an inch from the chassis, as shown in Figure 5-8. The sliding handles and XIO Tri-Module move out about one inch before the I/O panels move.
Page 142: Figure 5-10 Placing The Xio Tri-Module On Its Side
Chapter 5: Installing and Removing XIO Boards 4. Place the XIO Tri-Module on a ﬂat, antistatic surface, such as an empty antistatic bag on your desk. When the XIO Tri-Module is out of the chassis, the sliding handles must protrude, as shown in Figure 5-10.
Page 143: Figure 5-11 Placing A Cap On The Xio Compression Connector
Removing the XIO Tri-Module 5. Place a cap on the VPro graphics board compression connector, as shown in Figure 5-10 and Figure 5-11. Spare caps are included with your workstation. Caution: To prevent damage to the connector, do not touch or bump the gold (front) surface.
Page 144: Removing An Option Board Or Blank Panel
Chapter 5: Installing and Removing XIO Boards Removing an Option Board or Blank Panel Before removing an option board, or blank panel from slot C or D, you must power off your workstation, wait 5 minutes, attach the wrist strap, and remove the XIO Tri-Module (See “Preparing the Workstation”...
Page 145: Figure 5-13 Placing The Cap On The Xio Compression Connector
Removing an Option Board or Blank Panel Caution: Do not touch the gold XIO compression connector. Before you remove an option board place a cap on the XIO compression connector, as shown in Figure 5-13, to prevent accidental damage when removing the board. Caution - Do not touch Figure 5-13 Placing the Cap on the XIO Compression Connector...
Page 146: Figure 5-14 Removing The Screws From The Blank Panel
Chapter 5: Installing and Removing XIO Boards 6. Using the supplied Phillips screwdriver, remove the screws from the option board or blank panel, as shown in Figure 5-14. Figure 5-14 Removing the Screws from the Blank Panel 7. Grasp the blank panel or option board on the front and on the side of the board with no connectors and lift, as shown in Figure 5-15.
Page 147: Installing An Option Board Or Blank Panel
Installing an Option Board or Blank Panel 8. With the same side facing up, place the board on a clean, antistatic surface. Store the blank panel in a safe place. You may need to reinstall it if you remove an option board.
Page 148: Figure 5-16 Installing The Screws
Chapter 5: Installing and Removing XIO Boards 3. Place the option board or blank panel on the standoffs. Some option boards must be placed in designated slots. Always check your option board installation manual for information about board placement or other pertinent information.
Page 149: Figure 5-17 Removing The Cap From The Xio Board Compression Connector
Installing an Option Board or Blank Panel 5. Remove the cap from the XIO compression connectors, as shown in Figure 5-17. Keep the caps to protect the compression connector if you remove any XIO board. Caution - Do not touch Removing the Cap from the XIO Board Compression Connector Figure 5-17...
Page 150: Reinstalling The Xio Tri-Module
Chapter 5: Installing and Removing XIO Boards Reinstalling the XIO Tri-Module Caution: To prevent damage to your workstation, reinstall the XIO Tri-Module with the VPro graphics I/O panel aligned with the top of the workstation, as shown in Figure 5-18. Follow these instructions to reinstall the XIO Tri-Module: 1.
Page 151: Figure 5-18 Inserting The Xio Tri-Module
Reinstalling the XIO Tri-Module Inserting the XIO Tri-Module Figure 5-18 6. Tighten the captive screws in the sliding handles, as shown in Figure 5-19. Start by tightening a few threads on each captive screw before fully tightening. Tip: Tightening the XIO Tri-Module Screws Figure 5-19...
Page 152: Figure 5-20 Reconnecting The Monitor Cable
8. Reconnect all cables to the XIO Tri-Module. 9. Connect any new cables to the XIO Tri-Module. To monitor Figure 5-20 Reconnecting the Monitor Cable You are ﬁnished installing your XIO option board. Go to “Powering On the Octane2 Workstation” on page 127.
Page 153: Powering On The Octane2 Workstation
Powering On the Octane2 Workstation Powering On the Octane2 Workstation 1. Plug the power cable into an electrical outlet (see A in Figure 5-21). 2. Press the power button (B) on the front of your workstation. 3. Press the monitor power switch (C) to turn on your monitor.
Page 154: Verifying The Option Board Installation
Chapter 5: Installing and Removing XIO Boards Verifying the Option Board Installation To verify that your graphics or option boards are recognized, follow these instructions: 1. From Toolchest > Desktop, open a UNIX shell. 2. At the prompt, type: hinv. 3.
Page 155: Installing And Removing External Devices
Chapter 6 Installing and Removing External Devices This chapter provides information about SCSI bus bandwidths and rates, SCSI and serial device cabling, rules for daisy-chaining peripherals, pointers to conﬁguration documentation, and instructions for installing and removing external devices. For information on internal SCSI devices, see Chapter 7, “Installing and Removing Internal Drives and Front Module Parts.”...
Page 156: About Scsi Buses And Devices
About SCSI Buses and Devices SCSI devices continue to evolve with higher bus bandwidths, faster data transfer rates, and channels with longer cables and more devices. The Octane2 workstation has two wide SCSI buses, one for internal devices and one for external devices.
Page 157: Installing External Scsi Devices
To daisy-chain a mix of wide and narrow devices, place the wide devices (as a group) closest to the Octane2 workstation where the bus is wide, and place the narrow devices (as a group) at the end of the daisy chain.
Page 158: Assigning A Scsi Address On An External Device
1. If your workstation is powered off, turn on the power. 2. Log in to your account. For more information on logging in, go to “Logging In to the Octane2 Workstation” on page 21. 3. When the system comes up, choose Toolchest > System > System Manager >...
Page 159: Setting The Scsi Address On An External Device
To set the SCSI address, locate a switch, button, dial, or jumpers on the external device, then manually set the address to the number you chose in step 4 of the previous section. Although you can connect up to 15 wide SCSI devices to the Octane2 workstation, Note: some devices may have SCSI address dials that provide only 9 possible addresses.
Page 160: About Cables
Chapter 6: Installing and Removing External Devices About Cables You can connect one or more external SCSI devices to the SCSI port on the back of your workstation. Connecting more than one device is called daisy-chaining. You connect external SCSI devices in a chain, with the ﬁrst device attached to the SCSI port on your workstation.
Page 161: Shutting Down And Powering Off The System
2. Unplug the power cable from the electrical outlet (B) and from your workstation. 3. Press the monitor power switch (C) to power off your monitor. Power button Power cable Power switch Figure 6-2 Powering Off the Octane2 Workstation...
Page 162: Preparing A Scsi Device For Cabling
Chapter 6: Installing and Removing External Devices Preparing a SCSI Device for Cabling 1. If you are daisy-chaining a new SCSI device to a connected SCSI device, remove the terminator from the connector on the last device in the current chain by squeezing the clips on both sides of the terminator and pulling it off.
Page 163: Cabling The Devices
SCSI device 50-pin active 68-pin active terminator terminator 68-pin high-density to 50-pin Centronics 16-bit Ultra SCSI device 8-bit SCSI device 50-pin active terminator 68-pin high-density to 50-pin Centronics Figure 6-4 Using the Correct Cables between Devices and/or the Octane2 Workstation...
Page 164: Figure 6-5 Comparing Speed Of Daisy-Chained Devices
To daisy-chain an Ultra SCSI device to another Ultra SCSI device, use a 68-pin to 68-pin cable. To daisy-chain an Ultra SCSI device to a Fast SCSI device, use a 68-pin to 50-pin Centronics Fast SCSI cable. OCTANE2 8-bit Fast SCSI-2 device 8-bit Fast SCSI-2 device 10 MB/sec...
Page 165: Connecting Scsi Devices
Connect the other end of the SCSI cable to one of the SCSI connectors on the back of the device and secure the clips on each side of the connector. SCSI Figure 6-6 Connecting an External SCSI Device to the Octane2 Workstation...
Page 166: Figure 6-7 Daisy-Chaining An External Scsi Device To Another External Scsi
Chapter 6: Installing and Removing External Devices Connect one end of the SCSI cable to the open connector on the ﬁrst SCSI device, as shown in Figure 6-7. Attach the other end of the SCSI cable to one of the connectors on the SCSI device you are adding.
Page 167: Figure 6-8 Connecting The Terminator And Power Cable To An External Device
Installing External SCSI Devices 2. Connect the terminator to the last device in the daisy chain (see A in Figure 6-8). Make sure you secure the clips on each side of the terminator. The terminator is designed to ﬁt in only one direction. 3.
Page 168: Powering On The Octane2 Workstation
Chapter 6: Installing and Removing External Devices Powering On the Octane2 Workstation 1. Plug in the power cable (see A in Figure 6-9). 2. Replace the lockbar (if one was removed). Open the cover on the front of your workstation.
Page 169: Testing An External Device
Always turn on the external SCSI device(s) before turning on your workstation; Tip: otherwise, the system does not recognize the device. Power button Power cable Switch Power switch Power switch Figure 6-10 Turning On External Devices and the Octane2 Workstation...
Page 170: Figure 6-11 Identifying The Cd-Rom Icon
5. When you see the login screen, log in to your account. For more information on logging in, go to “Logging In to the Octane2 Workstation” on page 21. If the SCSI device is installed correctly, an icon representing the device appears on the desktop.
Page 171: Table 6-4 Additional References On External Scsi Devices
Powering On the Octane2 Workstation 4. If the device is the last SCSI device on the chain, make sure a terminator is plugged into one of its SCSI connectors. 5. Restart your system and recheck the System Manager listing or hinv listing (see step 1).
Page 172: Cleaning Dat Or Dlt Drives
Chapter 6: Installing and Removing External Devices Cleaning DAT or DLT Drives If you use a DAT or DLT drive frequently, magnetic dust or debris can collect on the heads of the drive. This can make your DAT or DLT tapes unreadable or unwriteable. If the green LED on the front of the DAT drive ﬂashes at about 5-second intervals, clean the DAT drive heads.
Page 173: Installing Serial Devices
Modems About Serial Ports The Octane2 workstation has two PC-compatible serial ports. You can also conﬁgure these ports to operate in other modes. Adapter cables are available that simplify interconnection for each of these modes. For more information, see “Serial Port Adapter...
Page 174: Installing The Serial Device
Chapter 6: Installing and Removing External Devices Installing the Serial Device To install a serial device, follow these steps: 1. Locate the serial ports on the back of your workstation, as shown in Figure 6-12. Serial ports are labeled and are DB9 connectors. 2.
Page 175: Figure 6-13 Plugging In The Serial Cable
Installing Serial Devices 3. Attach the serial device cable. See the instructions included with the serial device for detailed instructions on connecting the cable to the device. Plug the other end of the cable to the serial connector on the back of your workstation, as shown in Figure 6-13.
Page 176: Configuring The Device
Choose Toolchest > Help > Online Books > Personal System Administration Guide, and search for “Setting Up Serial Peripherals.” Installing Audio Devices All Octane2 audio ports are located on the upper left side of the system module, as shown in Figure 6-14. Microphone...
Page 177: Installing The Microphone
Installing Audio Devices Installing the Microphone Attach the microphone to your workstation as follows: 1. Place the microphone cord through the slot in the microphone base. 2. Slide the microphone into the base, as shown in Figure 6-15. 3. Place the microphone on top of the monitor (in the center, near the front). 4.
Page 178: Installing The Speakers And Headphones
Before connecting the speakers, power off your workstation. For instructions on shutting down and powering off the Octane2 workstation, see “Shutting Down and Powering Off the System” on page 135. Then return to this page for instructions on connecting the speakers.
Page 179: Figure 6-17 Attaching The Speaker Cables To The Active Speaker
Installing Audio Devices 4. On the cable with double connectors on each end, locate the end with one female connector and one male connector. 5. Attach the female power connector to the middle port on the right (active) speaker, as shown in Figure 6-17. 6.
Page 180: About Analog Line Level Audio
Chapter 6: Installing and Removing External Devices 9. Power on your workstation. For instructions, see “Powering On the Octane2 Workstation” on page 157. Speaker Power Figure 6-18 Attaching the Speaker Cables to the Octane2 Workstation For pinout and technical information, see Appendix B, “Technical Speciﬁcations,” or Octane2 Hardware Central.
Page 181: About Coaxial Digital Audio
Do not touch the tip of the ﬁber optic cable, or performance may be reduced. Note: Optical digital cable should be three meters or less. Using a longer cable may cause performance to be reduced. For pinout and technical information, see Appendix B, “Technical Speciﬁcations” or Octane2 Hardware Central.
Page 182: Replacing The Keyboard Or Mouse
Chapter 6: Installing and Removing External Devices Replacing the Keyboard or Mouse 1. Follow the instructions for “Shutting Down and Powering Off the System” on page 135. SGI recommends that you connect the keyboard to the keyboard port, and the mouse to the mouse port.
Page 183: Powering On The Octane2 Workstation
Powering On the Octane2 Workstation Powering On the Octane2 Workstation 1. Plug in the power cable to an electrical outlet (see A in Figure 6-20). 2. Press the power button (B) on your workstation. 3. Press the monitor power switch (C) to power on your monitor.
Page 185: Installing And Removing Internal Drives And Front Module Parts
Chapter 7 Installing and Removing Internal Drives and Front Module Parts This chapter shows you how to remove and install an internal drive, light module, frontplane module, system fan, and the external plastics located behind the bezel on the front of your workstation. Installing an internal drive is an easy task that requires no tools or screws.
Page 186: Installing And Removing Internal Drives
• The option drive above it is SCSI ID 0-2. • The option drive at the top of the Octane2 workstation is SCSI ID 0-3. • Bus 1 (external devices) has addresses such as 1-1, 1-2, 1-3. To determine the total capacity and megabytes available on your disks, choose Tip: the Toolchest >...
Page 187: Shutting Down And Powering Off The System
2. Unplug the power cable from the electrical outlet and from your workstation (B). 3. Press the monitor power switch (C) to power off your monitor. Power button Power cable Power switch Powering Off the Octane2 Workstation and Monitor Figure 7-1...
Page 188: Removing The Bezel
To remove the bezel, follow these steps: 1. Locate the lockbar, as shown in Figure 7-2. If a lockbar is not installed, skip to step 4. Lockbar slot Figure 7-2 Locating the Lockbar on the Front of the Octane2 Workstation...
Page 189: Figure 7-3 Unlocking And Removing The Lockbar
Installing and Removing Internal Drives 2. Unlock and remove the lockbar (see A in Figure 7-3). 3. Close the door (B) on the front of your workstation. Figure 7-3 Unlocking and Removing the Lockbar 4. Press both bezel release buttons, as shown in Figure 7-4. Figure 7-4 Pressing the Bezel Release Buttons...
Page 190: Figure 7-5 Removing The Bezel
Chapter 7: Installing and Removing Internal Drives and Front Module Parts 5. Remove the bezel by tilting it forward, then lifting it from its release hooks at the bottom, as shown in Figure 7-5. Figure 7-5 Removing the Bezel...
Page 191: Installing Secondary (Option) Internal Drives
Installing and Removing Internal Drives Installing Secondary (Option) Internal Drives To prepare your workstation for installation of a secondary internal drive, see “Shutting Down and Powering Off the System” on page 161, then follow the instructions for “Removing the Bezel” on page 162. The secondary drive bays are the two top drive bays, as shown in Figure 7-6.
Page 192: Figure 7-7 Inserting A Secondary (Option) Internal Drive
Chapter 7: Installing and Removing Internal Drives and Front Module Parts 1. Lift the handle on the drive to a horizontal position, then slide the drive into the drive bay. The drive handle is the same color as the drive. See Figure 7-7. 2.
Page 193: Figure 7-8 Locking The Secondary (Option) Drive
Installing and Removing Internal Drives 3. With the drive completely inserted, rotate the handle downward to lock the drive in the workstation, as shown in Figure 7-8. Drive handle Locking the Secondary (Option) Drive Figure 7-8 You are ﬁnished installing a secondary internal drive and are ready to remove the blank panel on the bezel.
Page 194: Removing The Blank Panel
Chapter 7: Installing and Removing Internal Drives and Front Module Parts Removing the Blank Panel After installing a new option drive, remove a blank panel from the bezel. 1. Place the bezel on a ﬂat surface with the door facing up. 2.
Page 195: Figure 7-10 Releasing The Blank Panel
Installing and Removing Internal Drives 4. Press down on the blank panel covering the desired drive bay, as shown in Figure 7-10. The blank panel pops out the back of the bezel. Store the blank panel in a safe place. You must replace it if you remove the drive. Caution: To prevent damage to your workstation, you must place a blank panel in the bezel if you remove a drive.
Page 196: Removing Internal Secondary (Option) Drives
Chapter 7: Installing and Removing Internal Drives and Front Module Parts Removing Internal Secondary (Option) Drives To remove an internal secondary (option) drive, see “Shutting Down and Powering Off the System” on page 161 and follow the instructions through “Removing the Bezel.” Then return to this page and follow these steps: 1.
Page 197: Replacing A Blank Panel
Installing and Removing Internal Drives 2. Pull the drive directly toward you to remove it from the drive bay, as shown in Figure 7-12. For instructions on installing a drive in a secondary (option) drive bay, go to“Installing and Removing Internal Drives” on page 160. To leave the drive bay empty, replace the blank panel before replacing the bezel, as described in the next section.
Page 198: Figure 7-13 Replacing The Blank Panel
Chapter 7: Installing and Removing Internal Drives and Front Module Parts 4. Press the blank panel until both sides snap ﬁrmly into place. Figure 7-13 Replacing the Blank Panel...
Page 199: Replacing The System Drive
Caution: Do not remove the system drive unless you have a new system drive to replace it. A system drive must remain in place to prevent damage to the Octane2 workstation. The SCSI ID of the system drive is 0-1.
Page 200: Figure 7-15 Unlocking The System Drive
Chapter 7: Installing and Removing Internal Drives and Front Module Parts To replace the system drive, follow these steps: 1. Locate the system drive. 2. Raise the handle to a horizontal position, as shown in Figure 7-15. Option drive bays System drive Light module Figure 7-15...
Page 201: Figure 7-17 Inserting The New Drive
Installing and Removing Internal Drives 4. Replace the system drive, as follows: Lift the handle. With the handle fully extended, gently slide the drive into the drive bay, as shown in Figure 7-17. The drive is connected to the frontplane when the front edge of the drive is ﬂush with the chassis.
Page 202: Testing An Internal Drive
Figure 7-18. Go to “Reinstalling the Bezel” on page 195 and follow the instructions through powering on the Octane2 workstation. When you see the login screen, you are ready to log in. Return to this section to test the internal drive.
Page 203: Removing And Replacing The Light Module
System Manager list again. Removing and Replacing the Light Module The light module provides the light for the light bar on the front of the Octane2 workstation. The light module is located on the sheet-metal face, behind the bezel, as shown in Figure 7-19.
Page 204: Figure 7-20 Removing The Light Module
Chapter 7: Installing and Removing Internal Drives and Front Module Parts The light module is located directly below the system drive. To replace the light module, go to “Shutting Down and Powering Off the System” on page 161 and follow the instructions through “Removing the Bezel.”...
Page 205: Figure 7-21 Inserting The Light Module
Light module Inserting the Light Module Figure 7-21 You are ﬁnished installing the light module and are ready to replace the bezel. Go to “Reinstalling the Bezel” on page 195 and follow the instructions through “Powering On the Octane2 Workstation.”...
Page 206: Removing And Replacing The Frontplane Module
Chapter 7: Installing and Removing Internal Drives and Front Module Parts Removing and Replacing the Frontplane Module You must remove the frontplane module if you want to install a new system fan or a new frontplane module. If you are installing a new frontplane module, you must also remove the system identiﬁcation module, as described later in this section.
Page 207: Preparing The Workstation To Remove The Frontplane Module
(as described below). Bookmarking these sections can help you organize this task. For help identifying Octane2 components, refer to the illustrations in Chapter 1. Make sure you have the new part nearby before beginning the replacement procedure.
Page 208 Chapter 7: Installing and Removing Internal Drives and Front Module Parts 3. Face the front of your workstation and follow these steps: Remove the system drive and any option drives (for more information, go to “Replacing the System Drive” on page 173 and “Removing Internal Secondary (Option) Drives”...
Page 209: Removing The Frontplane Module
Removing and Replacing the Frontplane Module Removing the Frontplane Module If you did not attach the wrist strap and prepare your workstation, go to “Removing and Replacing the Frontplane Module” on page 180 and follow the instructions before you begin this procedure. 1.
Page 210: Figure 7-24 Placing The Frontplane Module Face Down On A Clean Surface
Chapter 7: Installing and Removing Internal Drives and Front Module Parts 4. Gently place the frontplane module face down on the antistatic bag, as shown in Figure 7-24 To adjust the position of the frontplane module, handle it by the metal frame to avoid damaging components.
Page 211: Removing And Reinstalling The System Identification Module
Removing and Replacing the Frontplane Module If you did not attach the wrist strap, prepare your workstation, and remove the frontplane module, go to “Removing and Replacing the Frontplane Module” on page 180 and follow the instructions before you begin this procedure. Removing and Reinstalling the System Identiﬁcation Module Remove the system identiﬁcation module only if you are installing a new Note:...
Page 212: Installing The Frontplane Module
Chapter 7: Installing and Removing Internal Drives and Front Module Parts Installing the Frontplane Module Follow these steps to replace or reinstall the frontplane module: 1. Grasp the frontplane module by the metal frame on the edge of the front plane. 2.
Page 213: Removing And Replacing The System Fan
The procedure for replacing the system fan includes a number of steps from earlier sections of this guide (as described below). Bookmarking these sections can help you organize this task. For help identifying Octane2 components, see the illustrations in Chapter 1. Make sure you have the new fan nearby before beginning the replacement procedure.
Page 214: Removing The System Fan
Chapter 7: Installing and Removing Internal Drives and Front Module Parts 5. Follow the instructions in the next two sections for removing and replacing the system fan, then reinstall the system drive, any internal secondary drives, the light module, frontplane module, and bezel. Removing the System Fan 1.
Page 215: Replacing The System Fan
Removing and Replacing the System Fan Figure 7-28 Removing the Fan From the Back of the Drive Bay Replacing the System Fan 1. Gently slide the new cable connector onto the connector on the back of the drive bay. 2. Place the new fan on the back of the drive bay, as shown in Figure 7-29. The fan snaps into place when properly aligned.
Page 216: Removing And Replacing The Plastics: Top And Base
Chapter 7: Installing and Removing Internal Drives and Front Module Parts Removing and Replacing the Plastics: Top and Base To remove the plastics, top or base, you must shut down your system and remove the bezel. Go to “Shutting Down and Powering Off the System” on page 161 and follow the instructions through “Removing the Bezel”...
Page 217: Figure 7-31 Sliding The Front Cover Forward
Removing and Replacing the Plastics: Top and Base 4. After the cover slides forward, lift it straight up and off the chassis, as shown in Figure 7-31. 5. Install the new top cover. Slide the new top cover straight down over the chassis. Slide the new top cover back until it snaps into place.
Page 218: Removing And Installing The Base
Chapter 7: Installing and Removing Internal Drives and Front Module Parts Removing and Installing the Base To remove the base, you need to shut down the system, remove the bezel, and remove the top cover. To shut down the system, go to “Shutting Down and Powering Off the System” on page 161 and follow the steps through “Removing the Bezel”...
Page 219: Figure 7-33 Releasing The Plastic Base
Removing and Replacing the Plastics: Top and Base 2. Use a ﬂat-sided screwdriver to press down on the plastic release tab, as shown in Figure 7-33. Metal tab Plastic release tab Figure 7-33 Releasing the Plastic Base 3. While pressing down on the tab, slide the chassis back about 1-1/2 inches, until it stops, as shown in Figure 7-34.
Page 220: Figure 7-35 Lifting The Octane2 Workstation Off The Plastic Base
4. Lift the chassis straight up and off the base, as shown in Figure 7-35. Warning: Do not attempt to lift the Octane2 workstation by yourself. It is heavy and requires two people to safely lift. 5. Place the new base on a clean surface.
Page 221: Reinstalling The Bezel
When the bezel is properly installed, you can hear the latches snap into place. To reinstall the lockbar, go to the next section, “Reinstalling the Lockbar” on page 196. Otherwise, skip to “Powering On the Octane2 Workstation” on page 197.
Page 222: Reinstalling The Lockbar
Chapter 7: Installing and Removing Internal Drives and Front Module Parts Reinstalling the Lockbar 1. Open the door on the front of your workstation. 2. Insert the lockbar into the front of your workstation, with the angled end up (see A in Figure 7-37). 3.
Page 223: Powering On The Octane2 Workstation
Removing and Replacing the Plastics: Top and Base Powering On the Octane2 Workstation 1. Plug the power cable into a wall outlet (see A in Figure 7-38). 2. Power on the Octane2 workstation. Press the power button (B). Close the door.
Page 225: Troubleshooting
Chapter 8 Troubleshooting This chapter helps you isolate and solve possible problems with your workstation. The following topics are covered: • “Using the LEDs on the Lightbar” on page 200 • “Using the NMI Button” on page 203 • “Accessing the System Maintenance Menu” on page 204 •...
Page 226: Figure 8-1 Lightbar Leds - Front Of Octane2, Diagnostic Chart #1
• Replace system drive • Replace DIMMs • Replace CPU • Replace dual processor Contact your local SGI service provider. Have your system serial number ready for part replacement information. Lightbar LEDs - Front of Octane2, Diagnostic Chart #1 Figure 8-1...
Page 227: Figure 8-2 Lightbar Leds - Front Of Octane2, Diagnostic Chart #2
• Power Off - Replace system module • Replace system board • Replace speakers Contact your local SGI service provider. Have your system serial number ready for part replacement information. Lightbar LEDs - Front of Octane2, Diagnostic Chart #2 Figure 8-2...
Page 228: Figure 8-3 Lightbar Leds - Front Of Octane2, Diagnostic Chart #3
• Replace monitor • Replace system board • Replace system board • Replace system board Contact your local SGI service provider. Have your system serial number ready for part replacement information. Lightbar LEDs - Front of Octane2, Diagnostic Chart #3 Figure 8-3...
Page 229: Using The Nmi Button
Using the NMI Button Using the NMI Button If your system is experiencing problems and no error information is provided, you can force a non-maskable interrupt (NMI). When you press the NMI button, the system saves a record of its activity to a ﬁle and then powers down. Caution: When you push the NMI button, you lose any work in progress at the moment.
Page 230: Accessing The System Maintenance Menu
1. Press the power button on the front of your workstation to shut down and power off, as described in “Shutting Down and Powering Off the Octane2 Workstation” on page 25. You can also shut down and power off using the System menu in the Toolchest, Note: as described in Chapter 1.
Page 231: Running Diagnostic Tests
Running Diagnostic Tests Running Diagnostic Tests You can run the following software diagnostic tests on the Octane2 workstation: • Power-On Tests • Conﬁdence Tests • IDE Tests Power-On Tests These tests run automatically for the major hardware components each time you turn on your workstation.
Page 232: Ide Tests
Chapter 8: Troubleshooting IDE Tests The Interactive Diagnostic Environment (IDE) tests are more comprehensive than the conﬁdence tests, and run longer (up to 30-45 minutes). To perform these tests, follow these steps: 1. Turn off your workstation, wait a few seconds, then turn it on again. After a while, the Start notiﬁer appears, as shown in Figure 8-6.
Page 233: Recovering From A System Crash
Recovering From a System Crash Recovering From a System Crash In most cases, your system recovers from a system crash automatically when you reboot. If, however, you lose data on your system disk, and you cannot communicate with your workstation using the mouse or keyboard, or over the network, follow the steps in this section.
Page 234: Figure 8-8 Start Notifier
Chapter 8: Troubleshooting After a while, the Start Notiﬁer appears, as shown in Figure 8-8. Figure 8-8 Start Notiﬁer 2. Click Stop for Maintenance in the Start notiﬁer, or press The System Maintenance menu appears. 3. Choose Recover System in the System Maintenance menu, or type The System Recovery menu appears, as shown in Figure 8-9.
Page 235 Recovering From a System Crash If you do not have a CD-ROM drive, use a drive that is connected to another Note: system on the network and click Remote Directory in the System Recovery Menu. You are prompted to enter the remote hostname. Type the system’s name, a colon (:), and the full pathname of the remote CD-ROM drive, followed by .
Page 236 Chapter 8: Troubleshooting 6. Remove the CD, insert your most recent full backup tape, and then press Enter The system pauses while the backup program retrieves several ﬁles from the backup tape, and then the following message appears for each ﬁlesystem that was installed at the time of the backup.
Page 237: Disabling The System Maintenance Password
4. Place the jumper on the left and middle pins within the rectangle. The password is now disabled. 5. Go to “Reinstalling the System Module” on page 53 and follow the instructions through “Powering On the Octane2 Workstation” on page 58.
Page 238: Figure 8-10 Removing The Jumper For Disabling The Password
Chapter 8: Troubleshooting Caution - Do not touch Figure 8-10 Removing the Jumper for Disabling the Password...
Page 239: Enabling The System Maintenance Password
7. Place the jumper on the middle and right pins (within the rectangle). The password is now enabled. You are ready to replace the system module. Go to “Reinstalling the System Module” on page 53 and follow the instructions through “Powering On the Octane2 Workstation” on page 58.
Page 240: Figure 8-11 Removing The Jumper To Enable The Password
Chapter 8: Troubleshooting Caution - Do not touch Figure 8-11 Removing the Jumper to Enable the Password...
Page 241: System Does Not Power Off
System Does Not Power Off System Does Not Power Off If the system does not power off, either it never came up all the way or the operating system is hung. If you do not see any activity for several minutes, follow these steps: 1.
Page 242: Returning Parts
Chapter 8: Troubleshooting Returning Parts To return any part, use the packaging materials and box that came with your replacement part. For product support information, see page xxiv.
Page 243: Care And Cleaning Of Compression Connectors
Appendix A Care and Cleaning of Compression Connectors The Octane2 workstation uses compression connectors to connect several modules and boards to the frontplane. A single compression connector is used on the following components: • Back of the PCI module •...
Page 244: Storing And Handling The Compression Connector
Appendix A: Care and Cleaning of Compression Connectors Storing and Handling the Compression Connector To avoid damaging a compression connector and to keep it in optimal working condition, follow these guidelines when a board or module is not installed. Caution: Failure to follow these instructions can result in irreparable damage to the surface of the connector’s pads, which may result in intermittent or complete failure of the product.
Page 245: Cleaning A Compression Connector
Cleaning a Compression Connector Cleaning a Compression Connector A compression connector should never require cleaning if you keep its protective cover on when the module or board is not in the chassis. However, if the connector gets dirty, follow these steps for removing pollutants. Some pollutants can irreversibly damage (corrode or chemically alter) the pad Note: surfaces.
Page 246: Figure A-2 Spraying The Compression Connector
Appendix A: Care and Cleaning of Compression Connectors 6. Start spraying. As you spray, move the spray along the length of the compression connector until the entire length is sprayed. Move down a few rows and spray again along the entire length.
Page 247: Technical Speciﬁcations
Or, choose Toolchest > Help > InfoSearch, and type (You Octane2 Hardware Central cannot access Octane2 Hardware Central from the Online Books path). Port Pinout Assignments This section contains port pinout information for the following Octane2 ports: • “Audio Ports” – Microphone –...
Page 248: Audio Ports
The following diagram shows the microphone port pinout. Ground (-) Signal (+) Table B-1 shows the microphone port pinout information. Table B-1 Microphone Port Pinout Microphone Ring Sleeve Silicon Graphics- Signal(+) Signal(+) Ground(-) supplied electret NC (no connection) mono microphone Line level mono Ground (-)
Page 249: Speaker Port Pinout
Port Pinout Assignments Speaker Port Pinout The following diagram shows the port and plug pinout for the speaker/headphone port. Ground (-) Signal (+) Table B-2 shows the port pinout assignments for the speaker/headphone port. Speaker/Headphone Port Pinout Table B-2 Speaker/Headphone Signal Ring Sleeve Left...
Page 250: Analog Line Level Port Pinout
Appendix B: Technical Specifications Analog Line Level Port Pinout The following diagram shows the pinouts for the analog audio ports and plugs. Ground/return Ground/return Signal Signal Right Left White The following diagram shows the port (jack) pinout for the coaxial digital ports and plugs.
Page 251: Optical Digital Port Pinout
Port Pinout Assignments Optical Digital Port Pinout The following diagram shows the optical digital port, which has these features: • Supports ADAT 8-channel, 24-bit connections. • Compatible with consumer formats including CP340, IEC958, and S/PDIF.
Page 252: Scsi Port
Appendix B: Technical Specifications SCSI Port The following diagram shows the SCSI port. Table B-4 shows the cable and pinout assignments for the SCSI port. Table B-4 SCSI Port Pinout Assignment Assignment Ground DB(12) Ground DB(13) Ground DB(14) Ground DB(15) Ground DB(P1) Ground...
Page 253 Port Pinout Assignments Table B-4 (continued) SCSI Port Pinout Assignment Assignment Ground Ground Ground Ground Termpwr Termpwr Termpwr Termpwr Open Open Ground Ground Ground Ground Ground Ground Ground Ground Ground Ground Ground Ground Ground Ground DB(8) Ground DB(9) Ground DB(10) Ground DB(11)
Page 254: Ethernet 10-Base-T/100-Base-T Port
Appendix B: Technical Specifications Ethernet 10-Base-T/100-Base-T Port The Octane2 workstation autoselects the speed and type (duplex vs. half duplex) at bootup, based on what it is connected to. 1 2 3 4 5 6 7 8 Table B-5 shows the cable pinout assignments for the Ethernet 10-Base-T/100-Base-T port.
Page 255: Parallel Port
Port Pinout Assignments Parallel Port The following diagram shows the EEE 1284-C parallel port. 36 19 Table B-6 shows the cable pinout assignments for the IEEE 1284-C parallel port. Table B-6 Parallel Port Pinout Assignment Assignment BUSY Signal ground (BUSY) SELECT Signal ground (SELECT) nACK...
Page 256: Keyboard And Mouse Ports
Appendix B: Technical Specifications Table B-6 (continued) Parallel Port Pinout Assignment Assignment nSELECTIN Signal Ground (nSELECTIN) nAUTOFD Signal Ground (nAUTOFD) HOST LOGIC HIGH 36 view PERIPHERAL LOGIC HIGH Keyboard and Mouse Ports The following diagram shows the standard pinout for PC PS/2 keyboards and mice. The mouse and keyboard are electrically PS/2-compatible.
Page 257: Serial Ports
Port Pinout Assignments Serial Ports The Octane2 workstation serial ports can operate in one of several modes: • RS-232 electrical levels with a standard PC pinout. • Macintosh-style electrical levels and a Macintosh-compatible pinout (This mode requires an additional adapter cable. See “Serial Port Adapter Cables” on page 235).
Page 258: Table B-9 Serial Port Pinout - Macintosh-Compatible
Appendix B: Technical Specifications Table B-8 (continued) Serial Port Pinout - PC-Compatible Assignment Description Clear to send Ring indicator Table B-9 shows cable pinout assignments for the Macintosh-compatible serial ports (This mode requires an additional adapter cable. See “Serial Port Adapter Cables” on page 235).
Page 259: Serial Cables And Adapters
Serial Cables and Adapters Serial Cables and Adapters This section contains cable pinout information for serial cables that you can connect to your Octane2 workstation. It also describes SGI serial port converters. The following topics are covered: • “Printer/Dumb Terminal Serial Cable”...
Page 260: Pc Modem Serial Cable
Appendix B: Technical Specifications PC Modem Serial Cable Use a full-handshake (includes RTS and CTS) PC modem serial cable for a modem with RTS/CTS ﬂow control. Table B-11 shows the cable connector pin assignments for this cable. You can use this cable for all serial devices except those that do not need RTS ﬂow control. If you add a null modem adapter to one end of the cable, you can still use it with devices like serial printers and dumb terminals that do not need RTS ﬂow control.
Page 261: Serial Port Adapter Cables
The Octane2 workstation’s serial ports conform to the PC standard pinout for EIA standard RS-232 signals. The purpose of the adapter cable is to allow the Octane2 workstation to use standard PC or Macintosh serial devices. Table B-12 shows the adapter cable pinout for a standard PC or Macintosh serial port.
Page 262: Table B-13 Female Db9 To Female Db9 Adapter Cable Pinout
Table B-13 shows the pinout for a female DB9 to female DB9 adapter cable. Table B-13 Female DB9 to Female DB9 Adapter Cable Pinout Female DB9 Female DB9 Connected to Peripheral Connected to Octane2 Unused To DB9 -2 (RxD-) To DB9-8 (TxD-) Unused To DB9-6and DB9-4 (GND)
Page 263: Vpro Graphics Board I/O Ports
VPro Graphics Board I/O Ports VPro Graphics Board I/O Ports Monitor Port The following diagram shows the monitor port. 9 10 Table B-14 shows the port pinout assignments for the 20-inch monitor. Table B-14 20-Inch Monitor Pinout Assignment Red signal, analog Green signal, analog Blue signal, analog Monitor ID bit 3, TTL...
Page 264: Table B-15 Ddc-Enabled Monitor Pinout
Appendix B: Technical Specifications Table B-15 shows the port pinout assignments for an Octane2 DDC-enabled monitor. Table B-15 DDC-Enabled Monitor Pinout Assignment Green Blue Data clock (SCL) Bi-directional data (SDA) Composite sync Horizontal sync Vertical sync DDC (+5VInput) DDC ground...
Page 265: Table B-16 Vpro Graphics Board Scan Rates
VPro Graphics Board I/O Ports Table B-16 lists the VPro graphics board supported scan rates. Table B-16 VPro Graphics Board Scan Rates Format Name Vertical Refresh Rate (Hz) 640 x 480_60 59.940 800 x 600_60 60.317 1024 x 768_60 60.004 1024 x 768_75 60.317 1280 x 720_60...
Page 266: Stereoview Port
Appendix B: Technical Specifications StereoView Port The following diagram shows the StereoView Port. Table B-17 shows the cable pinout assignments for the StereoView port on the VPro graphics board. Table B-17 StereoView Pinout Assignments Assignment +12V DC output to StereoView device Ground Stereo left/right Eye signal (1=left, 0=right) (STEREO_LEFT)
Page 267: Genlock Port
VPro Graphics Board I/O Ports Genlock Port The following diagram shows the Genlock port. Table B-18 shows the cable pinout assignments for the Genlock port on the VPro graphics board. Genlock Pinout Assignments Table B-18 Assignment Genlock Input/output video or 3.3V TTL signal levels Sigma - return ground Swap Ready Port The following diagram shows the Swap Ready port.
Page 268: Physical Environment Specifications
Appendix B: Technical Specifications Physical Environment Speciﬁcations Table B-20 shows the physical environent speciﬁcations for the Octane2 workstation. Table B-20 Physical Environment Speciﬁcations Workstation dimensions 16.25” (41.3 cm) H x 11.0” (28 cm) W x 13.25” (33.7 cm) D 14.75” D (37.5 cm) (depth in localized area of power supply) 16.25”...
Page 269: Microphone Specifications
Physical Environment Specifications Microphone Speciﬁcations Table B-21 shows the microphone speciﬁcations. Table B-21 Microphone Speciﬁcations Microphone Jack Connector 3.5 mm stereo mini Power +5 V phantom power on tip Type Unidirectional electret condenser Speaker Speciﬁcations Table B-22 shows the speaker speciﬁcations. Table B-22 Speaker Speciﬁcations Speakers...
Page 270: Headphone Specifications
Total power for the PCI module (the sum of power for all boards from all power supply rails) must not exceed 45.0W (average 15.0W per board). The Octane2 PCI module is a 5V system environment. Table B-25 PCI Module Power Speciﬁcations...
Page 271 Physical Environment Specifications For additional information see Section 4.3.4.1, in the chapter called “Power Note: Requirements,” in the PCI Local Bus Speciﬁcation, Rev. 2.1, June l995 (PCI Special Interest Group, Portland, OR).
Page 273: Regulatory Information
CMN Number The Octane2 model number, or CMN number, is on the system label on the back of your workstation, as shown in “Back View” on page 4. You must provide the CMN number to SGI to obtain the Manufacturer’s Declaration of Conformity.
Page 274: Manufacturer's Declaration Of Conformity
1. If you received a system upgrade label, place it on the system label. Face the back of the Octane2 workstation. The system label is located at the top center of the back of the workstation. See “Back View” on page 4.
Page 275: Class A
Class A Class A Table C-1 FCC Declaration of Conformance Trade Name SGI, Inc. Product Computer Graphics Workstation Model Number CMNB015A Date of Conformance 1/97 Responsible Party SGI, Inc. Address 2011 North Shoreline Boulevard Mountain View, California 94043-1389 Telephone (650) 933-3405 This equipment complies with Part 15 of the FCC Rules.
Page 276: Electromagnetic Emissions
Appendix C: Regulatory Information Caution: The user is cautioned that changes or modiﬁcations to the equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Electromagnetic Emissions The following information applies to the workstation base conﬁguration. See the Manufacturer’s Declaration of Conformity for your workstation’s speciﬁc classiﬁcation, which may be different from the base conﬁguration.
Page 277: Radio And Television Interference
Class A Radio and Television Interference The equipment described in this guide generates and uses radio frequency energy. If it is not installed and used in accordance with the instructions in this guide, it can cause radio and television interference. This equipment has been tested and complies with the limits for a Class A computing device in accordance with the speciﬁcations in Part 15 of FCC rules.
Page 278: Shielded Cables
Shielded Cables The Octane2 workstation is FCC-compliant under test conditions that include the use of shielded cables between Octane2 and its peripherals. Your Octane2 workstation and any peripherals you purchase from SGI have shielded cables. Shielded cables reduce the possibility of interference with radio, television, and other devices.
Page 279: Class B
Class B Class B Table C-2 FCC Declaration of Conformance Trade Name SGI, Inc. Product Computer Graphics Workstation Model Number CMNB015B Date of Conformance 1/97 Responsible Party SGI, Inc. Address 2011 North Shoreline Boulevard Mountain View, California 94043-1389 Telephone (650) 933-3405 This equipment complies with Part 15 of the FCC Rules.
Page 280: Electromagnetic Emissions
Appendix C: Regulatory Information Caution: The user is cautioned that changes or modiﬁcations to the equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Electromagnetic Emissions The following information applies to the workstation base conﬁguration. See the Manufacturer’s Declaration of Conformity for your workstation’s speciﬁc classiﬁcation, which may be different from the base conﬁguration.
Page 281: Shielded Cables
(ESD). ESD is a source of electromagnetic interference and can cause problems ranging from data errors and lockups to permanent component damage. Caution: While you are operating your Octane2 you keep all the covers and doors, including the plastics, in place. The shielded cables included with the workstation and...
Page 282 Appendix C: Regulatory Information An ESD wrist strap is included with some products, such as memory and graphics upgrades. The wrist strap is used when installing these upgrades to prevent the ﬂow of static electricity, and it should protect your system from ESD damage.
Page 283: Glossary
Glossary account See login account. active window The only window that recognizes input (activity) from the keyboard and mouse; only one window is active at a time. ADAT optical interface The ADAT optical interface provides a unidirectional point-to-point connection of 8 tracks of 24-bit digital audio, with subcodes, at professional sampling rates, on a single consumer-grade optical ﬁber.
Page 284 Glossary backup tape A tape that contains a copy of the ﬁles and directories on your hard disk. A full backup tape contains a copy of all ﬁles and directories, including IRIX, on your hard disk. baud rate The speed (calculated as bits per second) at which the computer sends information to a serial device, such as a modem or terminal.
Page 285 A cap that ﬁts over a compression connector and protects it from being damaged by dust, ﬁnger oil, scratches, dents, and so on. The cap must be on a compression connector attached to a module or XIO board whenever the board or module is out of the Octane2 workstation.
Page 286 You set the default printer using the Print Manager. defaults A set of behaviors that Silicon Graphics speciﬁes on every system. You can later change these speciﬁcations, which range from how your screen looks to what type of drive you want to use to install new software.
Page 287 Glossary disk resource Any disk (hard, tape, CD-ROM, or ﬂoppy) that you can access either because it is physically attached to your workstation with a cable or because it is available over the network using NFS. disk use The percentage of space on your disk that contains information. double-click To press and release a button twice, very rapidly.
Page 288 Glossary ﬁle A set of disk blocks in which you store information such as text, programs, or images that you created using an application. ﬁlesystem A hierarchy of directories and ﬁles. Directories contain other directories and ﬁles; ﬁles cannot contain directories. The root (/) directory is at the top of the hierarchy. form A window containing buttons that you must click and/or ﬁelds in which you must enter text.
Page 289 InfoSearch The Silicon Graphics online search tool that ﬁnds information by keyword, topic, or task. InfoSearch seeks information in all information sources: man (reference) pages, online books, application help, release notes, and task cards. InfoSearch is located in the Toolchest.
Page 290 Glossary A mouse-and window-based text editor included with the IRIX operating system. KB (kilobyte) The abbreviation for a standard unit for measuring the information storage capacity of disks and memory (RAM and ROM); 1024 bytes equal one kilobyte, in most cases. launch To start an application, often by double-clicking an icon.
Page 291 Glossary login screen The window that you see after powering on the system, before you can access ﬁles and directories. The window contains one icon for each login account on the system. male connector A connector that has raised edges, pins, or other protruding parts that you plug into a female connector.
Page 292 Glossary mount point The directory on your workstation from which you access information that is stored on a local or remote disk resource. mouse A hardware device that you use to communicate with windows and icons. You move the mouse to move the cursor on the screen, and you press its buttons to initiate operations. mouse pad For an optical mouse, this is the rectangular, metallic surface that reads the movements of the mouse.
Page 293 Glossary parallel port An outlet on the workstation to which you connect external printers and similar devices. password A combination of letters and/or numbers that only you know; it is analogous to a key and prevents unauthorized access to your system. It is an optional element of your login account.
Page 294 Glossary power supply The piece of hardware in the Octane2 chassis that directs power from an electrical outlet to the chassis, monitor, and internal SCSI devices. Printer Manager A tool that you access through either the System toolchest or the System Manager. Use it to set up printer software and monitor jobs that you send to the printer.
Page 295 The portion of the monitor that displays information. SCSI Small Computer System Interface (pronounced “scuzzy”). SCSI is a high-speed input/output speciﬁcation for small computers. The Octane2 workstation is SCSI-3 compliant and supports two Ultra fast/wide/single-ended SCSI buses, each capable of transferring data at 40 MB per second.
Page 296 Glossary SCSI terminator An electronics device, often an external plug, that is required at the end of each SCSI bus. The Octane2 workstation uses active terminators only on an external SCSI or Ultra-SCSI device, not on the workstation itself. select To position the cursor over an icon, and then click the left mouse button.
Page 297 Glossary static electricity Whenever your body comes in physical contact with metal parts (including printed circuit boards) of computer equipment, there is the potential for you to feel an electrical shock (electrostatic discharge, or ESD), which could damage the equipment. To prevent this, you must always wear a wrist strap when working with the internal parts of a workstation.
Page 298 The physical disk that contains the standard IRIX operating system software. System Manager A set of tools that the administrator uses to set up and manage the Silicon Graphics workstation. You access the System Manager through the System toolchest. system software The standard IRIX operating system software and Silicon Graphics tools.
Page 299 A ﬂat cable that you wrap around your wrist and attach to a metal part of the workstation whenever you work with internal components of the workstation. This prevents electrical shocks to yourself and the components. See also static electricity. XIO boards High-speed boards produced by Silicon Graphics such as graphics, networking, disk interface, or video boards.
Page 301: Index
Index active speaker 10, 11 cable controlled impedance address, SCSI ethernet analog line level audio keyboard audio devices monitor installing 150-154 mouse power 11, 14 requirements SCSI serial back view, workstation speaker banks, DIMM system module base, replacing cabling bezel SCSI devices locking CD-ROM drive...
Page 302 Index VPro graphics board 113, 117 static electricity XIO board 119, 121 verifying installation conﬁdence tests DIMM banks 47, 48 connectors DIMM bracket removing controlled impedance DIMM sockets 47, 48, 51 DLT drive connectors cleaning heat sinks connecting installing described removing 32, 41-43 documentation, online...
Page 303 Index rates internal drive testing ﬁber optic cable I/O connector ﬂoppy drive monitor cable connecting PCI module formatting 145, 146 I/O door folder icon closing 86-87 frontplane module opening 84-85 removing 180, 181, 183-184 for extra-long connectors 94-95 replacing I/O panel, blank front view, workstation installing removing...
Page 304 NMI button removing 89-90, 96 using static electricity verifying installation PCI cables installing PCI module Octane2 Hardware Central 2, 8, 23 described Octane2 Workstation installing 100-103 back view opening components placing door on front view reconnecting door...
Page 305 Index peripheral icon port release slots analog line level audio locating coaxial digital audio ethernet restart 29-30 keyboard R port microphone mouse optical digital power SCSI 10, 11 cable requirements speaker media speed power button 25-26 rates power cable SCSI buses monitor described PCI module...
Page 306 Index serial device reinstalling conﬁguring removing 36-40 installing 147-149 removing cables from replacing 53-57 serial ports assignments System SCSI controller described system shut down 25-28 setup shut down 25-28 failure single processor tape drive installing setting up removing 41-42 terminator speaker port and daisy chaining speakers...
Page 307 Index Wide SCSI rates workstation. See Octane2 Workstation wrist strap attaching frontplane module PCI board PCI module 72, 74 removing memory XIO option board XIO blank panel removing 118, 120 XIO option board described identifying slots installing 121-123 removing 118-121...

Silicon Graphics OCTANE2 Owner's Manual

Chapter 1

Quick Links

Related Manuals for Silicon Graphics OCTANE2

Summary of Contents for Silicon Graphics OCTANE2