Page 1 ® Silicon Graphics 330 Visual Workstation User’s Guide 007-4278-001...
Page 2 TRADEMARKS Silicon Graphics is a registered trademark and SGI and the SGI logo are trademarks of Silicon Graphics, Inc. Acer is a registered trademark of Acer Inc. Adaptec is a registered trademark of Adaptec, Inc. Apollo is a trademark of Avant! Corporation. Linux is a registered trademark of Linus Torvalds.
Page 3 Record of Revision Version Description June 2000 Initial Rev 007-4278-001...
Page 5: Table Of Contents
Contents Figures . . ix Tables . . xiii About This Guide. . xv Obtaining Publications . xv Reader Comments . . xvi System Setup . External Structure . Internal Structure . Pre-installation Instructions . Connecting External Devices . Installation of Customer Replaceable Components . .
Page 6 Contents System Board . . 55 Overview . 55 Processor . 55 Memory. . 56 System Chipsets . 56 Expansion Slots . 57 Hardware Management Support . 57 Major Components . . 58 System Component Installation . . 62 ESD Precautions . .
Page 7 Contents Advanced Options. .100 Memory/Cache Options . .101 PnP/PCI Options . .102 Load Default Settings . .105 Abort Settings Change .106 Exit Setup . .106 SCSISelect Configuration Utility . .109 SCSI Configuration Utility .109 Overview . .109 Default Values. .109 When to Use the SCSISelect Utility .
Page 8 Contents Use Conditions . Notice: Canadian Users Remarque à l’intention des utilisateurs canadiens . Important Safety Instructions . Laser Compliance Statement . CLASS 1 LASER PRODUCT . APPAREIL A LASER DE CLASSE 1. LUOKAN 1 LASERLAITE LASER KLASSE 1 . PRODUCTO LÁSER DE LA CLASE I .
Page 9: Figures
Figures Front Bezel . Figure 1-1 Rear Panel . Figure 1-2 I/O Ports Figure 1-3 Internal Structure . Figure 1-4 5.25-inch and 3.5-inch Drive Bays Figure 1-5 Connecting AC Power Cable . Figure 1-6 Connecting Keyboard, Mouse, and Ethernet Cable Figure 1-7 Connecting DB15 HD Video Cable .
Page 10 Figures Removing Expansion Card. . 39 Figure 2-18 Location of the Retaining Screw for the Expansion Slot Filler Plate . 40 Figure 2-19 Installing Expansion Card . . 41 Figure 2-20 Location of System Board Screw . . 43 Figure 2-21 Removing Retaining Bracket from System Board .
Page 11 Figures User Password Screen . . 98 Figure 4-14 Save Changes Screen . . 98 Figure 4-15 Advanced Options Screen . .100 Figure 4-16 Memory/Cache Options Screen . .101 Figure 4-17 PnP/PCI Options Screen . .102 Figure 4-18 Load Default Settings Screen . .105 Figure 4-19 Abort Settings Change Screen.
Page 13: Tables
Tables Tables System Board Components . 60 Table 3-1 System Error Messages . 68 Table 3-2 System Information Screen Parameters . . 76 Table 4-1 Product Information Screen Parameters . . 78 Table 4-2 Disk Drives Screen Parameters . 80 Table 4-3 IDE Drive Screen Parameters .
Page 15: About This Guide
About This Guide This guide provides information on using and administering a Silicon Graphics 330 Visual Workstation. The following topics are covered in this manual: • Chapter 1, “System Setup,” describes how to prepare the system for installation and how to connect it to its peripheral devices.
Page 16: Reader Comments
About This Guide Reader Comments If you have comments about the technical accuracy, content, or organization of this document, please tell us. Be sure to include the title and document number of the manual with your comments. (Online, the document number is located in the front matter of the manual.
Page 17: System Setup
Chapter 1 System Setup This chapter details the steps required to install a Silicon Graphics 330 Visual Workstation. It describes how to prepare the system for installation and how to connect it to its peripheral devices. It also provides a general description of the external and internal structure of the Silicon Graphics 330 Visual Workstation.
Page 18: External Structure
1: System Setup External Structure This section describes the external features of the system housing (the front bezel and the rear panel). • Front Bezel As illustrated in Figure 1-1, the ﬂoppy drive and up to three 5.25-inch devices are accessible from the front panel.
Page 19: Figure 1-2 Rear Panel
External Structure • Rear Panel As shown in Figure 1-2, the rear panel includes the AC power input socket, the rear system fans, six expansion slots, and the I/O panel. Figure 1-3 shows a detailed view of the I/O panel. Power supply rear screws Locking loop...
Page 20: Figure 1-3 I/O Ports
1: System Setup External SCSI Mouse port Keyboard port USB ports Serial port 1 Parallel port Serial port 2 Ethernet port Audio-In port MIC In port Line-Out port DVI-D-port S-Video-Out port Monitor port Figure 1-3 I/O Ports Note: *The DVI-D and S-Video ports may be optional on some versions of VPro Graphics.
Page 21: Internal Structure
Internal Structure Internal Structure This section describes the location of the main components inside the Silicon Graphics 330 Visual Workstation chassis as illustrated in Figure 1-4. Power supply Key lock Tamper switch Rear fan Internal drive cage System disk AGP Pro 4X slot...
Page 22: Pre-Installation Instructions
1: System Setup • The Silicon Graphics 330 Visual Workstation has three 5.25-inch and four 3.5-inch drive bays, as shown in Figure 1-5. All three 5.25-inch drive bays are externally accessible from the front panel. Two of the 3.25-inch drive bays are located on the front panel—the other two are housed and accessible inside the chassis.
Page 23: Figure 1-5 5.25-Inch And 3.5-Inch Drive Bays
Pre-installation Instructions 5.25" drive bay (CD-ROM drive installed) 5.25" drive bay 5.25" drive bay 3.5" drive bay 3.5" drive bay (floppy disk drive installed) Internal 3.5" drive slot Internal 3.5" drive bay (hard disk drive installed) Figure 1-5 5.25-inch and 3.5-inch Drive Bays 007-4278-001...
Page 24: Connecting External Devices
1: System Setup Connecting External Devices Follow the instructions in this section to connect the system to the power source and to its external peripheral devices. Caution: The power supply is switch-selectable for 110V or 220V AC power. Verify the voltage setting before plugging in the power cord.
Page 25: Figure 1-7 Connecting Keyboard, Mouse, And Ethernet Cable
Connecting External Devices 2. Connect the keyboard and mouse to the system as shown in Figure 1-7. 3. Connect the Ethernet cable to the system as shown in Figure 1-7. The built-in Ethernet port is designed for use with 10-Base-T or 100-Base-TX Ethernet networks and will automatically switch to the proper speed.
Page 26: Figure 1-8 Connecting Db15 Hd Video Cable
1: System Setup 4. Connect a DB15 HD video cable to the system as shown in Figure 1-8. 5. Connect the monitor to the power source as shown in Figure 1-8. Figure 1-8 Connecting DB15 HD Video Cable 007-4278-001...
Page 27 Connecting External Devices 6. Follow these directions to connect speakers to the system. Figure 1-9 illustrates the procedure: Note: Speakers on your Silicon Graphics 330 Visual Workstation may be an optional feature. Read the operating precautions in the Speaker Installation Guide before connecting the speakers to the system.
Page 28: Figure 1-9 Connecting Speakers
1: System Setup Input Signal Output Left speaker Subwoofer 18.5 Figure 1-9 Connecting Speakers 007-4278-001...
Page 29: Figure 1-10 I/O Panel
Connecting External Devices 7. Connect other external devices to their respective ports. Refer to Figure 1-10 for a detailed view of the I/O panel. External SCSI Mouse port Keyboard port USB ports Serial port 1 Parallel port Serial port 2 Ethernet port Audio-In port MIC In port...
Page 31: Installation Of Customer Replaceable Components
Chapter 2 Installation of Customer Replaceable Components This chapter describes how to install customer replaceable components. This includes the removal and replacement of the beam and bafﬂe, 3.5-inch and 5.25-inch drives, the power supply, the fans, expansion cards, the system board, and the I/O gasket. A description of the steps to be taken to prepare the system for installation is provided ﬁrst.
Page 32: Pre-Installation Instructions
2: Installation of Customer Replaceable Components Pre-installation Instructions The following steps describe how to prepare the system for the removal and installation of customer replaceable components: Turn off the system before opening the side panel. 2. Unplug the AC power cable from the wall socket and from the power supply. 3.
Page 33: Removing And Installing Drives
Removing and Installing Drives 4. If you will need access to the front panel drives, you will have to remove the bezel. Follow these instructions if you need to remove the bezel: Remove the side panel as explained in Step 3. b.
Page 34: Removing And Installing A 5.25-Inch Drive
ﬁller plate snaps into place. The following instructions describe how to install 5.25-inch drives: All drives are mounted on snap-on drive rails. The Silicon Graphics 330 Visual Workstation comes with two sets of spare 5.25-inch drive rails. The spare drive rails are located inside the chassis on the side of the 5.25-inch drive bays.
Page 35: Figure 2-3 Mounting Drive Rails To 5.25-Inch Drives
Removing and Installing Drives Mounting Drive Rails to 5.25-inch Drives Figure 2-3 4. To mount a drive in the drive cage, place the drive in the selected drive bay 5.25-inch and slide the drive into the bay until the rails snap into place. 5.
Page 36: Figure 2-4 Removing Bezel Blanking Plate
2: Installation of Customer Replaceable Components 6. The Silicon Graphics 330 Visual Workstation comes with two plastic blanking plates installed on the bezel. The following directions show how to remove and install the bezel blanking plates: • To remove a blanking plate, push on the release mechanism at one end of the blanking plate and pull the blanking plate out of the bezel.
Page 37: Figure 2-5 Installing Bezel Blanking Plate
Removing and Installing Drives • To install a blanking plate, insert one end of the blanking plate into its retaining notches, then push the other end until it snaps into place. See Figure 2-5 for an illustration of the procedure. Installing Bezel Blanking Plate Figure 2-5 7.
Page 38: Removing And Installing A 3.5-Inch Drive In The Front-Access Drive Cage
2: Installation of Customer Replaceable Components Removing and Installing a 3.5-inch Drive in the Front-Access Drive Cage The following instructions describe how to remove 3.5-inch drives from the front-access drive cage: Remove the side panel and the bezel as described in “Pre-installation Instructions” on page 16.
Page 39: Figure 2-7 Detaching 3.5-Inch Drive Filler Plate
Removing and Installing Drives The upper 3.5-inch front access drive bay is covered with a detachable ﬁller plate. Follow these instructions to detach the ﬁller plate: Note: Once removed, the ﬁller plate cannot be re-installed. • The lower 3.5-inch drive bay needs to be empty to proceed with the removal of the ﬁller plate;...
Page 40 Note: Use of 10,000 RPM drives in the front-access drive cage is not recommended. All drives are mounted on snap-on drive rails. The Silicon Graphics 330 Visual Workstation comes with two sets of spare 3.5-inch drive rails. One set of spare 3.5-inch drive rails is located inside the chassis on the side of the 5.25-inch drive...
Page 41: Figure 2-8 Mounting Drive Rails To 3.5-Inch Drives
Removing and Installing Drives Mounting Drive Rails to 3.5-inch drives Figure 2-8 5. To mount a drive in the front-access drive cage, place the drive in the 3.5-inch selected drive bay and slide the drive into the bay until the rails snap into place. Note: For a drive to be correctly mounted in the front-access drive cage, it must be installed right side up.
Page 42: Removing And Installing A 3.5-Inch Drive In The Internal Drive Cage
Note: Only low-proﬁle (i.e., one-inch) drives can be mounted in the internal drive cage. All drives are mounted on snap-on drive rails. The Silicon Graphics 330 Visual Workstation comes with two sets of spare 3.5-inch drive rails. One set of spare 3.5-inch drive rails is located inside the chassis on the side of the 5.25-inch drive...
Page 43: Figure 2-9 Mounting Drives In The Internal Drive Cage
Removing and Installing Drives Caution: For a drive to be correctly mounted in the internal drive cage, it must be installed upside down. NOTE Internal 3.5" drives install upside down Connectors face out Figure 2-9 Mounting Drives in the Internal Drive Cage 007-4278-001...
Page 44: Replacing The Power Supply
2: Installation of Customer Replaceable Components 6. Connect cables to the drive. 7. Replace the side panel as described in “Post-installation Instructions” on page 52. Replacing the Power Supply Follow the instructions in this section to remove and replace the power supply. Warning: Do not open the power supply.
Page 45: Figure 2-10 Removing Power Supply Inside Screw
Replacing the Power Supply Power supply inside screw Figure 2-10 Removing Power Supply Inside Screw 7. Pull the power supply out of the system, avoiding any physical contact between the power supply and any system component. 8. To install the power supply, keep the system resting on its right side. 9.
Page 46: Figure 2-11 Connecting Power Supply Cables
2: Installation of Customer Replaceable Components Power supply CD-ROM power Power for System additional board power 5.25" drives Floppy disk drive power Additional 3.5" disk drive power System disk power Figure 2-11 Connecting Power Supply Cables 13. Replace the side panel as shown in “Post-installation Instructions” on page 52. 007-4278-001...
Page 47: Replacing Fans
Replacing Fans Caution: The power supply is switch-selectable for 110V or 220V power. Verify the voltage setting before plugging in the power cord. 14. Reconnect the AC cable to the power supply and to the wall socket. Replacing Fans This section covers the removal and installation of the rear and front system fans. Replacing the Rear System Fan Follow the instructions in this section to remove and replace the rear system fan: Remove the side panel as shown in “Pre-installation Instructions”...
Page 48: Figure 2-12 Disengaging Release Buttons And Removing Rear Fan
2: Installation of Customer Replaceable Components Release buttons Disengaging Release Buttons and Removing Rear Fan Figure 2-12 6. Carefully remove the fan from the system without touching any system component. 7. To install the rear fan, keep the system resting on its right side. 8.
Page 49: Replacing The Front System Fan
Replacing Fans Rear fan connection Rear fan connection Figure 2-13 Connecting Rear Fan Cable Replacing the Front System Fan Follow these instructions to remove the front system fan: Remove the side panel and the bezel as shown in “Pre-installation Instructions” on page 16.
Page 50: Figure 2-14 Removing Front Fan Screw And Releasing Clips
2: Installation of Customer Replaceable Components Clip Clip Front fan screw Clip Removing Front Fan Screw and Releasing Clips Figure 2-14 5. Once the three clips are released, the fan plastic frame can be removed from the system. 6. The fan is held in its plastic frame by four fan retaining clips. To remove the fan from its plastic frame, place the frame on a ﬂat surface, with the frame facing down, as shown in Figure 2-15.
Page 51: Figure 2-15 Removing Fan From Plastic Frame
Replacing Fans Retaining clips Retaining clips Removing Fan from Plastic Frame Figure 2-15 Follow these instructions to install the front system fan: To install the front fan, place the plastic frame on a ﬂat surface with its retaining clips facing up. 2.
Page 52: Figure 2-16 Installing Fan Into Plastic Frame
2: Installation of Customer Replaceable Components Cable hole Figure 2-16 Installing Fan into Plastic Frame 5. Place the fan plastic frame in the chassis and insert the frame guiding pins into their corresponding holes on the front panel. Push the fan frame until its retaining clips snap into place.
Page 53: Figure 2-17 Connecting Front Fan Cable
Replacing Fans D IO ID E IN T F A C IN P Front fan Fan power connection Connecting Front Fan Cable Figure 2-17 007-4278-001...
Page 54: Replacing Expansion Cards
2: Installation of Customer Replaceable Components Replacing Expansion Cards This section describes how to remove and install PCI (Peripheral Component Interconnect) and AGP (Accelerated Graphics Port) cards. See Figure 2-1 on page 16 for the location of the expansion card slots. Follow electrostatic discharge (ESD) precautions.
Page 55: Figure 2-18 Removing Expansion Card
Replacing Expansion Cards Retaining screw Figure 2-18 Removing Expansion Card 4. If no other card will be installed in the empty slot, a ﬁller plate needs to be installed in the expansion slot opening. Follow these instructions to install a ﬁller plate in an expansion slot opening: •...
Page 56: Figure 2-19 Location Of The Retaining Screw For The Expansion Slot Filler Plate
2: Installation of Customer Replaceable Components The following instructions describe how to install expansion cards: Remove the side panel as described in “Pre-installation Instructions” on page 16, if not already done. 2. If a ﬁller plate covers the slot opening selected for installation, follow these instructions to remove it: •...
Page 57: Figure 2-20 Installing Expansion Card
Replacing Expansion Cards Retaining screw Installing Expansion Card Figure 2-20 5. Replace the side panel as shown in “Post-installation Instructions” on page 52. 6. When the system is turned on, the BIOS automatically detects and assigns resources to the new device. Note: The BIOS detects and conﬁgures only Plug and Play expansion cards.
Page 58: Replacing The System Board
2: Installation of Customer Replaceable Components Replacing the System Board This section describes how to remove and replace the Silicon Graphics 330 Visual Workstation system board. Follow electrostatic discharge (ESD) precautions. Electronic equipment can be irreparably damaged by ESD. Always follow these preventative measures when handling a system component: •...
Page 59: Figure 2-21 Location Of System Board Screw
Replacing the System Board System board screw Figure 2-21 Location of System Board Screw 6. Pull the system board away from the I/O gasket and lift the board away from the chassis. 7. To detach the retaining bracket from the system board, unsnap the release clip and remove the bracket retaining hooks from the system board.
Page 60: Figure 2-22 Removing Retaining Bracket From System Board
Clip Figure 2-22 Removing Retaining Bracket from System Board The following instructions describe how to install the Silicon Graphics 330 Visual Workstation system board: To mount the retaining bracket onto the system board, place the retaining hooks into their system board holes and snap the release clip onto the board. Figure 2-23 illustrates the procedure.
Page 61: Replacing I/O Panel Gasket
Replacing I/O Panel Gasket 2. The system should still be resting on its right side to facilitate the installation. 3. Place the system board into the chassis so as to align the I/O ports with their respective holes in the I/O gasket. 4.
Page 62: Figure 2-24 Positioning The System Board On Its Standoff Hooks
2: Installation of Customer Replaceable Components Standoffs Standoff hooks Figure 2-24 Positioning the System Board on its Standoff Hooks 007-4278-001...
Page 63: Figure 2-25 Removing I/O Panel Gasket
Replacing I/O Panel Gasket Notched fingers Figure 2-25 Removing I/O Panel Gasket The following instructions describe how to install the I/O panel gasket: Locate the four retaining slots on the system’s I/O panel opening. See Figure 2-26 for the location of the retaining slots. 2.
Page 64: Securing The System
Installing I/O Panel Gasket Securing the System The Silicon Graphics 330 Visual Workstation’s side panel can be locked into place on the system using a locking loop and a padlock, thus preventing access to the internal components of the system. The locking loop is stored in a slot on the chassis and needs to be moved to another slot to be used.
Page 65: Figure 2-27 Location Of Locking Loop
Securing the System Locking loop Locking loop slot Key lock Slot for Kensington lock Figure 2-27 Location of Locking Loop 007-4278-001...
Page 66: Figure 2-28 Removing Locking Hook From Its Storage Slot
2: Installation of Customer Replaceable Components 3. Remove the locking loop from its storage slot by pressing the two hooks towards each other and pushing the loop out of the chassis. Figure 2-28 illustrates the procedure. Removing Locking Hook from its Storage Slot Figure 2-28 4.
Page 67: Figure 2-29 Installing Locking Loop In Its Functional Slot
The system itself can be secured in a particular location by using a Kensington locking device. See Figure 1-2 on page 3 for the location of the Kensington lock slot. Note: A Kensington locking device is not included with the Silicon Graphics 330 Visual Workstation.
Page 68: Post-Installation Instructions
2: Installation of Customer Replaceable Components Post-installation Instructions After completing the installation of customer replaceable components, follow these instructions to ready the system for operation: If your installation involved the removal of the bezel, follow these steps to replace the bezel: •...
Page 69: Figure 2-31 Placing Side Panel Onto Lower Chassis Rail
Post-installation Instructions 2. Follow these steps to replace the side panel: • Locate the two tabs on the lower side of the side panel. • Place the two tabs onto the lower chassis rail. • Slide the side panel toward the rear of the system, until the rear tab hits the rear of the chassis and the side panel cannot be moved any farther.
Page 70: Figure 2-32 Sliding Side Panel Into Place
2: Installation of Customer Replaceable Components • Slide the side panel towards the front of the chassis until it ﬁts into place. The procedure is illustrated in Figure 2-32. • Tighten the two thumbscrews on the back of the case. Figure 2-32 Sliding Side Panel into Place 3.
Page 71: System Board
Chapter 3 System Board This chapter describes the system board and all its major components. It contains the system board layout, jumper settings, cache and memory conﬁgurations, and information on other internal devices. Overview The M25D system board is a PCI bus-based dual-processor system board built on an extended ATX baseboard.
Page 72: Memory
3: System Board enabling advanced imaging, 3D, streaming audio and video, and speech recognition applications. The Pentium III processor delivers higher performance than the previous Pentium processor while maintaining binary compatibility with all previous Intel architecture processors. This system board supports 133-MHz host bus frequencies for single or dual Pentium III processors running at either 733 to 800 MHz, as well as future generation Pentium processors.
Page 73: Expansion Slots
3D textures to be stored in main memory as well as video memory. The Silicon Graphics 330 Visual Workstation has an AGP Pro Slot which enables users to install both AGP or AGP Pro cards in the system.
Page 74: Major Components
3: System Board Major Components The system board has the following major components: • FC-PGA (Flip-Chip Pin Grip Array) sockets that support a single or dual PentiumIII processor running at 733 MHz or 800 MHz, as well as future generations of Pentium CPUs.
Page 75: Figure 3-1 System Board Layout
Major Components Figure 3-1 shows the layout of the system board. CN13 CN11 CN16 CN22 CN25 DIMM-3 DIMM-2 CN17 DIMM-1 CN20 PWR2 Front fan PWR1 CN18 CPU1 PCI 1 Fan2 PCI 2 PCI 3 PCI 4 CPU2 PCI 5 Rear fan Fan1 CN19 Figure 3-1...
Page 76: Table 3-1 System Board Components
3: System Board Table 3-1 describes the system board components in Figure 3-1. Table 3-1 System Board Components Item Description Internal buzzer Battery CPU socket 1 thermal sensor connector Above: PS/2 mouse port Below: PS/2 keyboard port USB ports Above: Parallel port Left: Serial port 1 Right: Serial port 2 BMC connector...
Page 77 Major Components System Board Components Table 3-1 (continued) Item Description CN21 Fax voice connector CN22 SCSI channel B connector (68-pin) (Ultra 160/m) CN25 SCSI channel A connector (68-pin) (Ultra 160/m) CN26 System fan connector CNX7 System fan connector DIMM1-3 DIMM slots Above: Audio-in port Below: Line-out port CPU socket 2 fan connector...
Page 78: System Component Installation
3: System Board System Board Components Table 3-1 (continued) Item Description Apollo Pro 133A chipset (south bridge) Adaptec AIC-7899 chipset WKUP1 Wake on Ring connector a. Default System Component Installation The following sections show you how to install system components like the CPU, memory modules, and expansion cards.
Page 79: Figure 3-2 Locking New Cpu In Socket
System Component Installation The system board supports dual Pentium III processors running at 733, 800, or 866 MHz, and future generations of Pentium CPUs on a 133-MHz system bus. Caution: Always observe the ESD precautions when installing or removing a system component.
Page 80: Figure 3-3 Locking Metal Bracket In Place
3: System Board Figure 3-3 Locking Metal Bracket in Place 5. Connect the 3-pin and 2-pin fan/heatsink cables to the system board. See Figure 3-1 on page 59 for the location of the fan/heatsink connectors. Note: The heatsink becomes very hot when the system is on. NEVER touch the heatsink with any metal or with your hands.
Page 81: Installing And Removing Memory Modules
System Component Installation Installing and Removing Memory Modules The three 168-pin sockets onboard support SDRAM-type DIMMs. You may install 64-MB, 128-MB, 256-MB, or 512-MB (single and double density) DIMMs for a maximum of 1.5 GB of system memory. Note: The SDRAM works at 3.3 volts only; 5-volt memory devices are not supported. This system board supports 100-MHz and 133-MHz SDRAM.
Page 82: Installing Expansion Cards
3: System Board Note: The DIMM socket is slotted to ensure proper installation. If you slip in a DIMM but it does not completely ﬁt, you may have inserted it the wrong way. Reverse the orientation of the DIMM. To remove a DIMM, press the holding clips on both sides of the socket outward to release the DIMM, as shown in Figure 3-5.
Page 83: Error Messages
Error Messages To install expansion cards, complete the following steps: Locate an empty expansion slot on the system board. 2. Remove the metal bracket located on the opposite side of the empty expansion slot using a Phillips screwdriver. 3. Insert an expansion card into the slot. Make sure that the card is properly seated. 4.
Page 84: System Error Messages
3: System Board System Error Messages A system error message indicates a problem with the computer itself and normally appears during the power-on self-test (POST), before the operating system prompt appears. Table 3-2 describes corrective actions for system error messages. Table 3-2 System Error Messages Message...
Page 85 Error Messages System Error Messages Table 3-2 (continued) Message Action Hard disk 0 error IDE Check all cable connections. Replace hard disk. primary channel master drive error IDE primary channel Check all cable connections. Replace hard disk. slave drive error Hard disk 1 error IDE Check all cable connections.
Page 86 3: System Board System Error Messages Table 3-2 (continued) Message Action Memory Error at: Contact your dealer. MMMM:SSSS:OOO (W:XXXX, R:YYYY) where: M: MB, S: segment, O: offset, X/Y: write/read pattern Memory resource Contact your dealer. conﬂict(s) Memory size mismatch Check the memory size based on the system CPU clock mismatch speciﬁcations.
Page 87 Error Messages Run Setup. You must know the correct conﬁguration values for your system before you enter Setup, which is why you should write them down when the system is correctly conﬁgured. An incorrect conﬁguration is a major cause of power-on error messages, especially for a new system.
Page 89: Setup Utility
Chapter 4 Setup Utility This chapter provides information about the system BIOS and tells how to conﬁgure the system by changing the settings of the BIOS parameters. Introduction Most systems are already conﬁgured by the manufacturer or the dealer. You do not need to run Setup when starting the computer unless you receive a Run Setup message.
Page 90: Figure 4-1 Basic Setup Utility Screen
4: Setup Utility The system supports two Setup utility levels: basic and advanced. Figure 4-1 shows the Basic Setup Utility screen and Figure 4-2 shows the Advanced Setup Utility screen. If you are an advanced user, you may want to check the detailed conﬁguration of your system.
Page 91: System Information
System Information Advanced Setup Utility screen Figure 4-2 System Information The screen in Figure 4-3 appears if you select System Information from the main menu: 007-4278-001...
Page 92: Figure 4-3 System Information Screen
4: Setup Utility SystemInformation Processor ..........PentiumIII ProcessorSpeed .
Page 93 System Information System Information Screen Parameters Table 4-1 (continued) Parameter Description Diskette drive A System’s current diskette drive A settings. Diskette drive B System’s current diskette drive B settings. IDE primary Current conﬁguration of the IDE device channel master connected to the master port of the primary IDE channel.
Page 94: Product Information
4: Setup Utility Product Information Figure 4-4 shows the Product Information screen, which contains the general data about the system, such as the product name, serial number, BIOS version, and so on. This information is necessary for troubleshooting, and it may be required when you ask for technical support.
Page 95: Disk Drives
Disk Drives Disk Drives Select Disk Drives to input conﬁguration values for disk drives. Figure 4-5 shows the Disk Drives screen. DiskDrives FloppyDriveA ..........[1.44MB 3.5-inch] FloppyDriveB .
Page 96: Ide Channel Type
4: Setup Utility Table 4-3 Disk Drives Screen Parameters Parameter Description Option Diskette drive Selects the ﬂoppy disk drive type 1.44 MB, 3.5-in. A and B None 360 KB, 5.25-in. 1.2 MB, 5.25-in. 720 KB, 3.5-in. 2.88 MB, 3.5-in. IDE primary These items let you select the IDE Auto channel...
Page 97: Figure 4-6 Ide Drive Screen
Disk Drives IDE Drive Screen Figure 4-6 Table 4-4 describes the parameters of the IDE Drive screen. Table 4-4 IDE Drive Screen Parameters Parameter Description Option Device Lets you specify the type of hard disk Auto detection installed in your system. If you want BIOS User mode to automatically conﬁgure your hard disk,...
Page 98 4: Setup Utility IDE Drive Screen Parameters Table 4-4 (continued) Parameter Description Option Sector Speciﬁes the number of sectors of your User input hard disk, and is automatically set depending on your Type parameter setting. Size Speciﬁes the size of your hard disk, in MB. User input Hard disk When set to Auto, the BIOS utility Auto...
Page 99: Onboard Peripherals
Onboard Peripherals IDE Drive Screen Parameters Table 4-4 (continued) Parameter Description Option Advanced When set to Auto, the BIOS utility Auto PIO mode automatically detects if the installed hard Disabled disk supports the function. If supported, it allows for faster data recovery and read/write timing that reduces hard disk activity time.
Page 100: Figure 4-7 Onboard Peripherals Screen
4: Setup Utility Figure 4-7 Onboard Peripherals Screen Table 4-5 describes the parameters in this screen. The settings in boldface are the default and suggested parameter settings. Table 4-5 Onboard Peripherals Screen Parameters Parameter Description Option Serial port 1 Enables or disables serial port 1. Enabled Disabled Base address...
Page 101 Onboard Peripherals Onboard Peripherals Screen Parameters Table 4-5 (continued) Parameter Description Option Sets the IRQ (interrupt request) channel of serial port 1. Serial port 2 Enables or disables the serial port 2. Enabled Disabled Base address Sets the I/O base address of serial 3F8h port 2.
Page 102 4: Setup Utility Onboard Peripherals Screen Parameters Table 4-5 (continued) Parameter Description Option Operation Selects the operation mode of the Bidirectional mode parallel port. Standard Parallel Port (Standard) - allows normal speed one-way Standard operation. Standard and Bidirectional (Bidirectional) - allows normal speed operation in a two-way mode.
Page 103: Power Management
Power Management Onboard Peripherals Screen Parameters Table 4-5 (continued) Parameter Description Option Onboard Enables or disables onboard audio Enabled audio chip feature. Disabled Onboard SCSI Enables or disables onboard SCSI Enabled feature. Disabled Onboard Enables or disables onboard network Enabled Ethernet chip feature.
Page 104: Table 4-6 Power Management Screen Parameters
4: Setup Utility Table 4-6 describes the parameters in this screen. The settings in boldface are the default and suggested parameter settings. Power Management Screen Parameters Table 4-6 Parameter Description Option Power Allows you to reduce power Enabled management consumption. When this parameter is set Disabled mode to Enabled, you can conﬁgure the IDE...
Page 105: Boot Options
Boot Options Power Management Screen Parameters Table 4-6 (continued) Parameter Description Option Power switch When set to Power Off, the system Suspend < 4 sec. automatically turns off when the power Power off switch is pressed for less than 4 seconds. When set to Suspend, the system enters the suspend mode when pressed for less than 4 seconds.
Page 106: Figure 4-9 Boot Options Screen
4: Setup Utility Boot Options Boot Sequence 1st [Floppy Disk A:] 2nd [Hard Disk C:] 3rd [IDE CD-ROM] Utility Fast Boot ..........[Auto] Silent Boot .
Page 107: Table 4-7 Boot Options Screen Parameters
Boot Options – Select “Set” to save your selection (after you have selected the hard disk you want to boot from). • Under “IDE CD ROM,” you can choose as follows: – Select “IDE CD ROM” if you want the system to check the CD-ROM drive for a bootable CD on boot-up.
Page 108 4: Setup Utility Boot Options Screen Parameters Table 4-7 (continued) Parameter Description Option Silent boot Enables or disables the Silent boot Enabled function. When set to Enabled, BIOS is in Disabled graphical mode and displays only an identiﬁcation logo during POST and while booting.
Page 109: Date And Time
Date and Time Date and Time The real-time clock keeps the system date and time. After setting the date and time, you do not need to enter them every time you turn on the system. As long as the internal battery remains good (approximately seven years) and connected, the clock continues to keep the date and time accurately even when the power is off.
Page 110: System Security
4: Setup Utility Table 4-8 describes the parameters of the Date and Time screen. Table 4-8 Date and Time Screen Parameters Parameter Description Date Set the date following the weekday-month-day-year format. Valid values for weekday, month, day, and year are: Weekday: Sun, Mon, Tue, Wed, Thu, Fri, Sat Month: Jan, Feb, Mar, Apr, May, Jun, Jul, Aug, Sep, Oct, Nov, Dec...
Page 111: Supervisor Password
System Security System Security Supervisor Password ........[None] User Password .
Page 112: Figure 4-12 Supervisor Password Screen
4: Setup Utility Enable the Supervisor Password parameter in the System Security menu by pressing the left or right arrow keys. The Supervisor Password screen appears, as shown in Figure 4-12. Supervisor Password Screen Figure 4-12 2. Type a password in the Enter Password ﬁeld. The password may consist of up to seven characters.
Page 113: User Password
System Security 6. Choose Yes to save your settings and exit Setup. Your password will be saved to CMOS. Removing the password To remove your Supervisor Password, complete the following steps: Disable the Supervisor Password parameter in the System Security menu by pressing the left or right arrow key to select None.
Page 114: Figure 4-14 User Password Screen
4: Setup Utility Enable the User Password parameter in the System Security menu by pressing the left or right arrow key. The User Password screen appears, as shown in Figure 4-14: User Password Screen Figure 4-14 2. Type a password in the Enter Password ﬁeld. The password may consist of up to seven characters.
Page 115: Disk Drive Control
System Security Removing a Password To remove your User Password, complete the following steps: Disable the User Password parameter in the System Security menu by pressing the left or right arrow key to select None. 2. Press the Esc key to return to the System Security menu and then press the Esc key again to exit Setup.
Page 116: Processor Serial Number
4: Setup Utility Processor Serial Number The Pentium III processor incorporates an individual serial number in each chip that can identify individual CPUs. When set to Enabled, CPUs can be identiﬁed by processor serial number. Disable this parameter to deactivate this feature. Advanced Options The Advanced Options screen lets you conﬁgure the system memory, PCI device settings, and CPU frequency.
Page 117: Memory/Cache Options
Advanced Options Memory/Cache Options The Memory/Cache Options screen, shown in Figure 4-17, lets you conﬁgure the advanced system memory functions. Memory/CacheOptions Level 1 Cache ..........[Enabled] Level 2 Cache .
Page 118: Pnp/Pci Options
4: Setup Utility Memory Cache Options Screen Parameters Table 4-10 (continued) Parameter Description Option Memory at To prevent memory address conﬂicts System 15MB-16MB between the system and expansion Expansion reserved for boards, reserve this memory range for the board use of either the system or an expansion board.
Page 119: Table 4-11 Pnp/Pci Options Screen Parameters
Advanced Options Table 4-11 describes the parameters of the PnP/PCI Options screen. Table 4-11 PnP/PCI Options Screen Parameters Parameter Description Option PCI IRQ setting Select Auto to let BIOS automatically Auto conﬁgure the plug and play (PnP) devices Manual installed on your system. Otherwise, select Manual.
Page 120 4: Setup Utility PnP/PCI Options Screen Parameters Table 4-11 (continued) Parameter Description Option PCI IRQ Setting this parameter to Yes allows you to sharing assign the same IRQ to two different devices. To disable the feature, select No. Note: If there are no IRQs available to assign for the remaining device function, it is recommended that you enable this parameter...
Page 121: Load Default Settings
Load Default Settings PnP/PCI Options Screen Parameters Table 4-11 (continued) Parameter Description Option Plug and play When this parameter is set to Yes, BIOS initializes only PnP boot devices such as SCSI cards. When set to No, BIOS initializes all PnP boot and non-boot devices such as sound cards.
Page 122: Abort Settings Change
4: Setup Utility Abort Settings Change Use this option to disregard your changes to the BIOS and reload your previous settings. The screen in Figure 4-20 appears when you select Abort Settings Change from the main menu. Figure 4-20 Abort Settings Change Screen Select Yes to disregard your changes and reload your previous settings.
Page 123: Figure 4-22 Save Changes Screen
Exit Setup If you made any changes to the Setup utility, the screen in Figure 4-22 is displayed. Figure 4-22 Save Changes Screen Use the arrow keys to select your response. Select Yes to save the changes in CMOS. Select No to retain the old conﬁguration values. Press the Enter key to exit. 007-4278-001...
Page 125: Scsiselect Configuration Utility
Some settings apply globally to the SCSI controller and all SCSI devices on the bus; other settings apply individually to each device on the bus. Note: The Silicon Graphics 330 Visual Workstation is equipped with a dual SCSI channel controller that enhances your system’s performance and ﬂexibility...
Page 126: When To Use The Scsiselect Utility
5: SCSISelect Configuration Utility Default Settings for SCSI Controller and All Devices Table 5-1 (continued) Global Settings for SCSI Controller and All Devices Default Value Host Adapter BIOS Enabled Support Removable Disks Under BIOS as Fixed Disks Boot only Extended BIOS Translation for DOS Drives > 1 Gbyte Enabled Display <Ctrl-A>...
Page 127: Scsiselect Utility Options
SCSISelect Utility Options SCSISelect Utility Options When the SCSISelect utility detects the AHA-3950U2B SCSI controller in your computer, it displays the Options menu shown below. SCSISelect (TM) Adaptec AIC-7899 Utility AIC-7899 at Bus:Device 01:06h Would you like to configure the host adapter, or run the SCSI disk utilities? Select the option and press <Enter>.
Page 128: Configure/View Host Adapter Settings Menu
5: SCSISelect Configuration Utility Conﬁgure/View Host Adapter Settings Menu The Conﬁgure/View Host Adapter Settings menu lists three settings under SCSI Bus Interface Deﬁnitions and three additional options, as shown below: • Host Adapter SCSI ID: changes the host controller SCSI ID from its default value of 7 •...
Page 129: Figure 5-3 Configure/View Host Adapter Settings Screen (2 Of 2)
SCSISelect Utility Options Adaptec AIC-7899 SCSISelect (TM) Utility AIC-7899 at Bus:Device 00:00h Configuration SCSI Bus Interface Definitions Host Adapter SCSI ID ..... . . SCSI Parity Checking .
Page 130: Figure 5-4 Host Adapter Scsi Id Selection Screen For Aha-3950U2B
5: SCSISelect Configuration Utility Host Adapter SCSI ID This option allows you to change the host controller SCSI ID. The ﬁgure below shows the available IDs for use with the AHA-3950U2B. The default setting is SCSI ID 7. (We recommend that you not change this setting.) Some operating system software will not run unless the SCSI controller ID is set at ID 7.
Page 131: Figure 5-5 Scsi Parity Checking Selection
SCSISelect Utility Options SCSI Parity Checking Select this option to enable or disable SCSI Parity Checking on the SCSI controller. The ﬁgure below displays your choices. The default setting is Enabled. SCSISelect (TM) Adaptec AIC-7899 Utility AIC-7899 at Bus:Device 01:06h Configuration SCSI Bus Interface Definitions Host Adapter SCSI ID .
Page 132: Figure 5-6 Host Adapter Scsi Termination Selection For Aha-3950U2B
5: SCSISelect Configuration Utility Host Adapter SCSI Termination This option allows you to conﬁgure host controller SCSI termination. The following ﬁgure shows the choices available if you have an AHA-3950U2B. Adaptec AIC-7899 SCSISelect (TM) Utility AIC-7899 at Bus:Device 01:06h Configuration SCSI Bus Interface Definitions Host Adapter SCSI ID .
Page 133: Figure 5-7 Boot Device Options Screen
SCSISelect Utility Options Boot Device Options This option shows the target ID of the device you are booting from. The default setting is 0 (zero). We recommend that you not change this setting. Some operating systems will not run unless the boot device is set at zero. The ﬁgure below shows the Boot Device Options screen.
Page 134: Figure 5-8 Scsi Device Configuration Screen For Aha-3950U2B
5: SCSISelect Configuration Utility SCSI Device Conﬁguration This option allows you to conﬁgure certain parameters of each SCSI device on the SCSI bus. A screen similar to the ﬁgure below appears. The screen shows a column of information for each SCSI ID, even if some SCSI IDs are not assigned to a device. To conﬁgure a speciﬁc SCSI device, you need to know which SCSI ID it uses.
Page 135 SCSISelect Utility Options Initiate Sync Negotiation This option determines whether the SCSI controller initiates synchronous negotiation with the SCSI device. When set to yes, the SCSI controller initiates synchronous negotiation with the SCSI device. When set to no, the SCSI controller does not initiate synchronous negotiation. The SCSI controller, however, always responds to synchronous negotiation if the SCSI device initiates it.
Page 136 5: SCSISelect Configuration Utility When set to yes, the SCSI device may disconnect from the SCSI bus. The SCSI device, however, may choose not to disconnect, even if permitted by the SCSI controller (this can usually be conﬁgured on the SCSI device). When set to no, the SCSI device is not allowed to disconnect from the SCSI bus.
Page 137: Figure 5-9 Advanced Configuration Options Screen
SCSISelect Utility Options Advanced Conﬁguration Options When you select Advanced Conﬁguration Options, a screen similar to the ﬁgure below appears. Do not change these options unless absolutely necessary. Adaptec AIC-7899 SCSISelect (TM) Utility AIC-7899 at Bus 03L:Device: 03h Channel A Advanced Configuration Options Enabled Reset SCSI Bus at IC Initialization .
Page 138 5: SCSISelect Configuration Utility Host Adapter BIOS This option enables or disables the SCSI controller BIOS. Default is Enabled. The SCSI controller BIOS must be enabled if you want the computer to boot from a SCSI hard disk drive connected to the SCSI controller. Several SCSISelect options cannot be used unless the SCSI controller BIOS is enabled.
Page 139 SCSISelect Utility Options Extended BIOS Translation for DOS Drives > 1 GByte This option allows you to enable or disable extended translation for SCSI hard disks with a capacity greater than 1 GByte. It is only valid if the SCSI controller BIOS is enabled. The default setting is Enabled.
Page 140: Scsi Disk Utilities
5: SCSISelect Configuration Utility SCSI Disk Utilities When you select SCSI Disk Utilities from the Options menu the SCSISelect utility scans the SCSI bus and lists all SCSI devices installed on the SCSI bus. You will see a screen similar to the ﬁgure below. You can easily determine from this screen which SCSI ID is assigned to each device on the SCSI bus.
Page 141 SCSISelect Utility Options Note: Use SCSI Disk Utilities to check the hard disk drive ﬁrmware version. Select SCSI Disk Utilities from the Conﬁgure/View Host Adapter Settings screen. Use the arrow keys to highlight a disk device, then press Enter to display the ﬁrmware version.
Page 143: Connector Pinouts
Appendix A Connector Pinouts This Appendix contains port pinout information for the following Silicon Graphics 330 Visual Workstation ports: • Keyboard Port • Mouse Port • Video-Out Ports – DB15 HD Port • Serial Ports • Parallel Port • USB Ports •...
Page 144: Keyboard Port
A: Connector Pinouts Keyboard Port The Silicon Graphics 330 Visual Workstation uses a standard PS/2 keyboard port, as shown in Figure A-1. Figure A-1 Keyboard Port Pinout Table A-1 shows the cable pinout assignments for the keyboard port. Table A-1...
Page 145: Mouse Port
Mouse Port Mouse Port The Silicon Graphics 330 Visual Workstation uses a standard PS/2 mouse port, as shown in Figure A-2. Figure A-2 Mouse Port Pinout Table A-2 shows the cable pinout assignments for the mouse port. Table A-2 Mouse Port Pinout...
Page 146: Video-Out Ports
A: Connector Pinouts Video-Out Ports The Silicon Graphics 330 Visual Workstation comes with an DB15 HD video port, an S-Video port and a DVI-D port. DB15 HD Port Figure A-3 shows the DB15 HD port. DB15 HD Port Pinout Figure A-3 Table A-3 shows the port pinout assignments for the DB15 HD port.
Page 147: Serial Ports
Serial Ports Serial Ports The Silicon Graphics 330 Visual Workstation serial ports use a standard PC-compatible pinout. The serial port supports data rates from 300 bits per second (bps) to 115.2 Kbps. Figure A-4 shows the serial port. Serial Port Pinout Figure A-4 Table A-4 shows cable pinout assignments for the serial ports.
Page 148: Parallel Port
A: Connector Pinouts Parallel Port The Silicon Graphics 330 Visual Workstation uses a standard DB25 1284 EPC parallel port, as shown in Figure A-5. Parallel Port Pinout Figure A-5 Table A-5 shows the cable pinout assignments for the parallel port.
Page 149: Usb Ports
USB Ports USB Ports The Silicon Graphics 330 Visual Workstation has two 4-pin USB connectors. Figure A-6 shows a USB port. Figure A-6 USB Port Pinout Table A-6 shows the cable pinout assignments for the USB ports. Table A-6 USB Port Pinout...
Page 150: Ethernet Port
A: Connector Pinouts Ethernet Port The Silicon Graphics 330 Visual Workstation has an RJ45 port for 10-Base-T or 100-Base-TX twisted-pair Ethernet. The port autoselects the speed (10 Mbps or 100 Mbps) and type (half duplex or full duplex) at bootup, based on what it is connected to.
Page 151: Audio Ports
Audio Ports Audio Ports The Silicon Graphics 330 Visual Workstation uses a 3.5 mm mini jack stereo microphone port, an analog line-level audio input port and an analog line-level audio output port. Table A-8 shows the port pinout information for the mic-in, line-in, and line-Out ports.
Page 153: Physical Environment Specifications
Appendix B Physical Environment Speciﬁcations Table B-1 shows the physical environment speciﬁcations for the Silicon Graphics 330 Visual Workstation. Table B-1 Physical Environment Speciﬁcations System dimensions 48.9 cm (19.25’’) H x 20.95 cm (8.25’’) W x 44.1 cm (17.375’’) D-without bezel, 49.16 cm (19.375’’) D-with bezel...
Page 154: Figure B-1 System Dimensions
B: Physical Environment Specifications Figure B-1 shows the system dimensions with bezel. 8.25 in. 19.375 in. 209.5 mm 491.6 mm 19.25 in. 489.0 mm Figure B-1 System Dimensions 007-4278-001...
Page 155: Regulatory Information
Appendix C Regulatory Information FCC Notice This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Page 156: Notice: Peripheral Devices
C: Regulatory Information Notice: Peripheral Devices Only peripherals (input/output devices, terminals, printers, etc.) certiﬁed to comply with the Class B limits may be attached to this equipment. Operation with non certiﬁed peripherals is likely to result in interference to radio and TV reception. Caution: Changes or modiﬁcations not expressly approved by the manufacturer could void the user’s authority, which is granted by the Federal Communications Commission, to operate this computer.
Page 157 Important Safety Instructions Follow all warnings and instructions marked on the product. 2. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 3. Do not use this product near water. 4.
Page 158: Laser Compliance Statement
C: Regulatory Information d. If the product does not operate normally when the operating instructions are followed. Adjust only those controls that are covered by the operating instructions since improper adjustment of other controls may result in damage and will often require extensive work by a qualiﬁed technician to restore the product to normal condition.
Page 159: Luokan 1 Laserlaite Laser Klasse 1
Lithium Battery Statement LUOKAN 1 LASERLAITE LASER KLASSE 1 VORSICHT: UNSICHTBARE LASERSTRAHLUNG, WENN ABDECKUNG GEÖFFNET NICHT DEM STRAHLL AUSSETZEN PRODUCTO LÁSER DE LA CLASE I ADVERTENCIA: RADIACIÓN LÁSER INVISIBLE AL SER ABIERTO. EVITE EXPONERSE A LOS RAYOS. ADVARSEL: LASERSTRÅLING VEDÅBNING SE IKKE IND I STRÅLEN VARO! LAVATTAESSA OLET ALTTINA LASERSÅTEILYLLE.
Page 160 C: Regulatory Information VARNING: Explosionsfara vid felaktigt batteribyte. Anvãnd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera anvãnt batteri enligt fabrikantens instruktion. VAROITUS: Päristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden mukaisesti.
Page 161: Index
Index Numbers AGP parameter Setup utility 3.5-inch drives Apollo Pro 133A chipset installing north and the south bridges on front-access drive cage on internal drive cage removing from front-access drive cage from internal drive cage base address parameter 5.25-inch drives Setup utility 84, 85 installing...
Page 162 Index LAN Desk Client Management (LDCM) diskette drive A parameter Setup utility CMOS saving changes diskette drive B parameter CMOS chip Setup utility CMOS RAM 71, 73 diskette drive parameters CMOS settings Setup utility saving DMA transfer mode parameter conﬁguration settings Setup utility battery power loss DRAM parameters...
Page 163 Index Setup utility expansion cards graphics aperture size parameter installation Setup utility expansion slot AGP bus PCI bus extended capabilites port system board hard disk 32-bit access parameter external devices connection 8 through 13 Setup utility external ports hard disk block mode parameter system board Setup utility hard disk drive parameter...
Page 164 DIMM socket Setup utility expansion cards level 2 cache size parameter memory modules Setup utility installing Load Default Settings Screen 3.5-inch drives Setup utility on front-access drive cage locking loop on internal drive cage 5.25-inch drives bezel drive rails on 3.5-inch drives main board ID parameter on 5.25-inch drives Setup utility...
Page 165 Index user PCI (Peripheral Component Interconnect) Onboard 10/100 Mb/s Intel 82559 LAN chip installation Onboard audio chip parameter PCI IRQ setting parameter Setup utility Setup utility Onboard Ethernet chip parameter PCI IRQ sharing parameter Setup utility Setup utility onboard LAN parameter PCI power management parameter Setup utility Setup utility...
Page 166 Index PS/2 mouse parameter Setup utility Save Changes Screen Setup utility SDRAMs system board memory read/write functions sector parameter disk drives Setup utility enable or disable serial number real-time clock processor rear fan serial number parameters installing Setup utility location of cable connection serial port 1 parameter removing Setup utility...
Page 167 Index Supervisor Password Screen overview System Information Screen processor System Security Screen removing User Password Screen SDRAMs side panel system board retaining bracket installing installing removing removing silent boot parameter system chipsets Setup utility Apollo Pro 133A LAN subsystem SIMD system date and time single processor MP table parameter Setup utility...
Page 168 Index User Password change or set removal User Password Screen Setup utility VGA palette snoop parameter Setup utility Wired for Management LAN subsystem wrist grounding strap 007-4278-001...

Silicon Graphics 330 User Manual

1 System Setup

2 Installation of Customer Replaceable Components

3 System Board

4 Setup Utility

5 Scsiselect Configuration Utility

Quick Links

Related Manuals for Silicon Graphics Silicon Graphics 330

Summary of Contents for Silicon Graphics Silicon Graphics 330

Table of Contents