Canon imageRUNNER ADVANCE 4551i Service Manual page 435

57B-8001-02
Detection Description
Remedy
57B-8002-02
Detection Description
Remedy
583-8001-02
Detection Description
Remedy
Error in the Paper End Pushing Guide Motor (Finisher-Y1)
The paper end pushing guide does not come off the Paper End Pushing Guide HP Sensor when
the Paper End Pushing Guide Motor has been driven for 1 second.
STAPLE FIN-Y1/BOOKLET FIN-Y1
[Related parts]
- Harnesses from the Paper End Pushing Guide HP Sensor (PS122) to the Finisher Controller
PCB
- Harnesses from the Paper End Pushing Guide Motor (M112) to the Finisher Controller PCB
- Paper End Pushing Guide HP Sensor (PS122)
- Paper End Pushing Guide Motor (M112)
- Finisher Controller PCB (PCB101)
[Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection
timing of this error, this error code may be displayed. Accordingly, perform the following work before
checking the related parts.
1. Check whether there is not the malfunction in the swing guide unit.
2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102).
[Remedy] Check/replace the related harness/cable, connector and parts.
[Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing
the Parts" in the Service Manual.
Error in the Paper End Pushing Guide Motor (Finisher-Y1)
The Paper End Pushing Guide HP Sensor does not detect the paper end pushing guide when the
Paper End Pushing Guide Motor has been driven for 1 second.
STAPLE FIN-Y1/BOOKLET FIN-Y1
[Related parts]
- Harnesses from the Paper End Pushing Guide HP Sensor (PS122) to the Finisher Controller
PCB
- Harnesses from the Paper End Pushing Guide Motor (M112) to the Finisher Controller PCB
- Paper End Pushing Guide HP Sensor (PS122)
- Paper End Pushing Guide Motor (M112)
- Finisher Controller PCB (PCB101)
[Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection
timing of this error, this error code may be displayed. Accordingly, perform the following work before
checking the related parts.
1. Check whether there is not the malfunction in the swing guide unit.
2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102).
[Remedy] Check/replace the related harness/cable, connector and parts.
[Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing
the Parts" in the Service Manual.
Error in the Tray Auxiliary Guide Motor (Finisher-Y1)
The tray auxiliary guides don't come off the Front/Rear Tray Auxiliary Guide HP Sensors when the
Tray Auxiliary Guide Motor has been driven for 1 second.
STAPLE FIN-Y1/BOOKLET FIN-Y1
[Related parts]
- Harnesses from the Front Tray Auxiliary Guide HP Sensor (PS117) to the Finisher Controller
PCB
- Harnesses from the Rear Tray Auxiliary Guide HP Sensor (PS118) to the Finisher Controller PCB
- Harnesses from the Tray Auxiliary Guide Motor (M109) to the Finisher Controller PCB
- Front Tray Auxiliary Guide HP Sensor (PS117)
- Rear Tray Auxiliary Guide HP Sensor (PS118)
- Tray Auxiliary Guide Motor (M109)
- Finisher Controller PCB (PCB101)
[Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection
timing of this error, this error code may be displayed. Accordingly, perform the following work before
checking the related parts.
1. Check whether there is not the mulfunction in the swing guide unit.
2. Check whether there is not the mulfunction in the Swing Guide Safety Switch (SW102).
[Remedy] Check/replace the related harness/cable, connector and parts.
[Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing
the Parts" in the Service Manual.
422
7. Error/Jam/Alarm