Nordson 3100V Series Customer Product Manual page 107

A
3-32
lnstallation
Programming SYSTEM
SETTINGS Controls
(contd.)
Feature
No.
Feature Description
Default
Setting
Optional
Settings
24
25
30&31
26
27
28
29
34
35
36
37
32
Auto-Energize
Pump
Auto-Energize
Heaters
Time
With
Heaters On
Fault Log (most
recent)
Fault Log
(second
most
recent)
Fault Log
(third
most
recent)
Auto Standby
Timeout
and
ln
Standby
Tlmeout
Auto-Energize
Pump
Temperature
Setting
Remote Pump
Enable/Remote
Heaters On
Warning
Log
(most recent)
Warning Log
(second
most
recent)
Warning Log
(third most
recent)
Piston
pump
units
only: Allows you
to
turn the
auto-energize pump feature on or
off.
lf this feature
is on,
the
system turns
the pump on automatically
once the
tank
reaches the
preset temperature
of Feature No.
32.
lf the
auto-energize pump feature
is off,
you
must turn
the pump
on
by pressing
the
PUMP key until
the
PUMP light
turns
on.
Allows
you
to turn the auto-energize
heaters feature on
or
off.
lf
the feature
is
on, the system turns heaters on
automatically
once
the
POWER switch
is
turned
on.
However,
if
you
have programmed the
system to turn
heaters on
and
off automatically, using the clock feature,
your clock settings override the auto-energize
heaters
feature.
lf
the auto-energize heaters feature
is off,
you
must
turn
heaters
on
manually, or
allow
any clock settings
you
have programmed to turn heaters on or off.
Allows you
to display the total time
(in hours)
that
the
heaters have been
running to assist with servicing and
maintenance.
Refer
lo
Checking
Run
Time
of
Heatersin
lhe
Maintenance section of this manual.
Allows you to display the cause of the most
recent system
fault.
Refer
to
Checking the Warning or Fault Login
lhe
Operation section for
a
list of fault codes.
Allows you
to display the cause of the second most recent
system
fault. Referto
Checking
the
Warning or
Fault Login
lhe
Operation section for a list of fault
codes.
Allows
you
to display the cause
of
the third most recent
system
fault.
Refer
to
Checking the Warning or Fault Log
in
lhe
Operation section for a
list of
fault
codes.
These features
are available only on units with
an
l/O
board.
Refer
to Seres 3000V lnput/Output
Boardinlhe
Options
seclion
of
this
manual
for information
on
customizing these features.
Piston
pump
units
only: Allows you
to determine when the
pump
automatically starts
if
you are using the auto-energize
pump feature (Feature No.
24).
You can have
the pump
start either when the system
reaches
the
READY condition
or when the tank reaches a
temperature you
have specified.
(See Note
B.)
This feature
is available only
on
units with
an l/O
board.
Refer
to
Series 3000V lnput/Output Boardinlhe Options
section
of
this
manual
for
information on customizing this
feature.
Allows you to
display the cause of the most recent system
warning.
Refer
to
Checking the
Warning or Fault Log in
lhe
Operation section for a list of warning codes.
Allows you to
display the cause of the second most recent
system
warning.
Refer
to Checking the
Warning or
Fault
Log
in
the
Operation section for a
list of
warning
codes.
Allows
you
to
display the cause of the
third most
recent
system
warning.
Refer to Checking the Warning or Fault
Log
in
the
Operation section for
a
list of
warning
codes.
(on)
1
1
(on)
See Note A
See
Note
A
See Note A
See Note A
0
(ready)
See Note A
See Note A
See
Note A
NOTE A:
B:
Features
26-29
and
35-37
are always
on.
There is no default setting.
lf you enter a setting that is higher than the tank
setpoint, the
pump will start when the
tank reaches its setpoint.
0 (off)
1 (on)
none
none
none
none
0 (ready
condition) or
1-23211450
('c/'F)
none
none
none
0
1
(off)
(on)
A3EN-04-[3V-X-4XXVj-1
3
41
-3000v
lssued
5/00
@
2000 Nordson Corporation
All
rights reserued