Nordson 3100V Series Customer Product Manual page 106

lnstallation
A 3-31
Table A
3-5
SYSTEM SETTINGS Features
Feature
No.
Feature Description
Default
Setting
Optional Settings
0
1
2
3
6-19
4
5
20
21
22
23
Password
Password Enable
System-Ready
Time
Delay
Overtemperature
Setpoint
Celsius/
Fahrenheit
Global
Temperature
Band
lndividual
Temperature
Bands
(See Note
D.)
Sequential or
Simultaneous
Startup
Display Heater
Proportioning
System
Warning
or Power
Notification
System
Ready or
Pump Notification
Provides a
turned
on.
password
if
the password
enable
feature
is
The password
(321) cannot be changed.
Allows
you
to turn the password enable feature
on or
off. When
the password
enable
feature
is on,
operators
can
view
the settings for TEMPERATURE,
SYSTEM SETTINGS, or
CLOCK.
To change the
settings,
operators
must enter the correct password
(321).
When the feature
is off, operators can change
all settings without entering a
password.
Allows you
to specify the amount
of additional
time
needed for the adhesive to melt after all zones
have
reached
their setpoint temperatures.
At the
end of the
time delay, the READY light turns
on.
Allows you
to specify the maximum temperature
any
zone can
reach before the system initiates a fault
condition.
This setting should
be
at
least 14
'C
(25
'F)
above the highest operating setpoint. The
system
will
not allow
you
to set the overtemperature
setpoint
lower than this,
or
the
operating setpoint
higher. (See Note A.)
Allows you
to display temperature
measurements
in
Celsius
or
Fahrenheit.
Allows you
to specify the degree to which a
temperature
may deviate from any zone before the
system indicates an out-of-band warning. (See
Note B.)
Allows you to
specify the degree to which a
temperature may deviate for an
individual
zone
before
the system
initiates a
warning.
(See Note C.)
Allows
you
to specify whether the system will perform
a sequential startup (internal zones
and hose zones
heat
first, then gun
zones) or simultaneous
startup (all
zones
heat at once).
Allows you
to display the
heater
proportioning
(a
flashing INTERNAL,
HOSE, or GUN light).
Allows you
to change the
System Warning output
contact
to aleft
remotely located operators that a
system warning has occurred
or
that power
is on.
Allows you to
change
the System
Ready output
contact to alert remotely located operators that
the
system is ready (up to temperature)
or that the pump
is on.
321
0
(off)
18 (minutes)
2',t81425
(.c/.F)
F (Fahrenheit)
17t30
("c/.F)
17t30
('cl"F)
1
(sequential)
0
(no display)
1
(warning)
1
(ready)
none
0 (off)
1
(on)
G-60 (minutes)
52-2461125475
('cl'F)
F (Fahrenheit)
C (Celsius)
6-2811
0-50
('cl'F)
6-2811
0-50
('cl'F)
0 (simultaneous)
1
(sequential)
0 (no display)
'l
(show display)
0 (power)
'1
(warning)
0 (pump)
1 (ready)
NOTE A:
B:
C:
The overtemperature setting should
be
at
least
42
"C
(75 "F)
below the
flash point temperature.
lf
you
enter a setting that is higher than the
tank setpoint, the
pump will start when the
tank reaches its setpoint.
lf you
enter a new setting for this feature, the
new
setting
is immediately entered for the
individual
zones (Feature
Nos.
6-19).
However, it is not saved
as
the
setting
for
Feature No. 5. Feature No. 5 always
returns to the default
setting of 6
oC
(10
'F).
D:
Feature No. 6
=
tank, Feature No. 7 =
grid,
Feature Nos. &-13 = hoses 1-6,
Feature Nos.
14-1g = guns 1-6
@
2000
Nordson Corporation
All
rights reserved
41-3000v
lssued 5/00
A3 EN-04-[3V-X-4XXyJ-1 3