Eaton i-on series Engineering Manual page 167

i-on Range
HUA Confirm ==
HUA Confirm Aux #
HUA Confirm Bell #
HUA Confirm RK==
HUA Confirm SRN==
HUA Confirm WAM==
HUA Confirm Websvr
HUA Confirm Z===
HUA Restore
HUA Restore
HUA Restore
HUA Z== Alarm
HUA Z== Restore
HUD Fault Rst Z===
HUD Fault Z===
IP Polling Fault
IP Polling Restore
Jamming ==
Jamming == Rstr
K== Excess Keys
Key Sw Ptn # PtSet
Key Sw Ptn # Set
Key Sw Ptn # Unset
Key Sw System PtSet
Key Sw System Set
Key Sw System Unset
Keypad == added
Keypad == found
Keypad 12V Fail
Keypad 12V Restore
Kpd == deleted
Lid Tamper Restore
Lockset Z=== Set
Lockset Z=== Unset
Low Batt Restore
Low Batt Z== Rstr
Low Battery
Low Battery Z==
Mains Fail
Mains Restore
Mask Flt Z==
Mask Restore Z==
Hold Up Alarm confirmed on
keypad HUA keys.
Hold Up Alarm confirmed by open
circuit on AUX Tamp terminals on
control unit PCB.
Hold Up Alarm confirmed by open
circuit on TR terminal on control
unit PCB.
Hold Up Alarm confirmed by
tamper on radio keypad.
Hold Up Alarm confirmed by radio
siren n tamper.
Hold Up Alarm confirmed by
tamper on WAM n.
A Hold Up Alarm was confirmed
by a user on the web browser
interface typing the password
incorrectly more than four times in
a row,
Hold Up Alarm confirmed on wired
zone nn.
Hold Up Alarm button has been
restored.
Hold Up Alarm has been restored.
Hold Up Alarm has been restored.
Hold Up Alarm on zone n.
Hold Up Alarm on zone restored.
A hold up device fault reported on
zone n was restored.
A hold up device reported a fault
on zone n.
The Chiron Ethernet or Chiron
GPRS plug on module is having a
problem.
The problem with the Chiron
Ethernet or Chiron GPRS module
has been restored.
Jamming detected.
Jamming ceased.
Excess keys tamper at keypad n.
Partition part set from keyswitch.
Partition set from keyswitch.
Partition unser from keyswitch.
System part set from keyswitch.
System set from keyswitch.
System unser from keyswitch.
New keypad added to system.
New keypad found on bus.
Bus DC power failed at keypad.
Bus DC power restored at keypad.
Keypad deleted from system.
Control unit lid closed.
A zone with type "lock set" was
closed. (If Inverted attribute is set
to "normal".)
A zone with type "lock set" was
opened. (If Inverted attribute is set
to "normal".)
Control unit battery no longer low.
Radio detector at zone has low
battery restored.
Control unit battery low.
Radio detector at zone has low
battery.
Mains fail at control unit.
Mains restored at control unit.
Masking detected on zone while
partition unset?
Masking restored on zone.
Mask Z==
Missing ==
Missing == Rstr
Missing ==ER
Missing ==ER Rs
Occupancy Set W#
Override
PA U-- Low Bat
Panel lid open
Panic == Alarm
Panic Alarm Rstr
Panic Alarm Rstr
Panic Alrm Rst P#
Panic Alrm Rst P#
Panic Alrm Rst P#
Panic U-- Alarm
Partn # Rearmed
Pend U-- Low Bat
Pri Comms Path Flt
Pri Comms Path Rst
Ptn # Remote Rst
Remote Reset
Remote U-- Low Bat
Remsvc Comms Fail
Remsvc Complete
RF Failure
RF Failure Restore
RF Jamming
RF Jamming Restore
RK == Panic Alarm
RK== Ex Keys Rstr
RK== Excess Keys
RK== Fire
RK== Low Battery
RK== RF OK
RK== RF Warning
RK== Superv Fail
RK== Superv Rstr
RK== Tamper
RK== Tamper Rstr
Sec Comms Path Flt
AppendixVII
Masking detected on zone while
partition set.
Expander missing from bus.
Missing expander restored to bus.
An External prox Reader
connected to keypad nn has gone
missing (possibly disconnected
from the keypad).
An External prox Reader
connected to keypad nn has been
re-connected.
A user set a ward while an
occupancy zone was active.
User overrode set fail in part
setting system.
Hold up Device belonging to user
has a low battery.
Control unit lid open.
Panic alarm at keypad.
Hold Up Alarm restored.
Hold Up Alarm from radio keypad
restored.
Panic alarm at keypad in partition
restored.
Hold Up Alarm in partition
restored.
Hold Up Alarm from radio keypad
in partition n reset.
User started a panic alarm from a
Hold Up Device.
Partition n was rearmed after an
alarm by control unit.
Pendant belonging to user has a
low battery.
Primary communications path has
a fault.
Primary communications path fault
restored.
User reset partition remotely.
User reset system remotely.
Remote control belonging to user
has low battery.
A remote service call failed all
attempts.
A remote service call succeeded.
Radio failed.
Radio restored.
Radio jamming detected.
Radio jamming removed.
Hold Up Alarm raised at radio
keypad n.
The system was restored after a
user keyed in the wrong code
more than four times in a row at
radio keypad n.
Radio keypad n has been
tampered by excess keypresses.
Fire alarm raised at radio keypad
n.
Radio keypad n has low battery.
Radio keypad n supervision OK.
Radio keypad n about to fail
supervision.
Radio keypad n failed supervision.
Radion keypad n supervision
restored.
Tamper on radio keypad n.
Tamper on radio keypad n
restored.
Secondary communications path
has a fault.
Page 157