1012
C
61: S
HAPTER
TATIC
R
C
OUTING
ONFIGURATION
1.1.1.0/24
1.1.1.1/32
1.1.4.0/30
1.1.4.1/32
1.1.4.2/32
127.0.0.0/8
127.0.0.1/32
g Tables: Public
Destinations : 7
Destination/Mask
0.0.0.0/0
1.1.2.0/24
1.1.2.3/32
1.1.4.0/30
1.1.4.1/32
127.0.0.0/8
127.0.0.1/32
# Display the IP routing table of Router B.
[RouterB] display ip routing-table
Routing Tables: Public
Destinations : 10
Destination/Mask
1.1.2.0/24
1.1.3.0/24
1.1.4.0/30
1.1.4.2/32
1.1.5.4/30
1.1.5.5/32
127.0.0.0/8
127.0.0.1/32
1.1.6.0/24
1.1.6.1/32
# Use the ping command on Host B to check reachability to Host A, assuming
Windows XP runs on the two hosts.
C:Documents and SettingsAdministrator> ping 1.1.2.2
Pinging 1.1.2.2 with 32 bytes of data:
Reply from 1.1.2.2: bytes=32 time=1ms TTL=128
Reply from 1.1.2.2: bytes=32 time=1ms TTL=128
Reply from 1.1.2.2: bytes=32 time=1ms TTL=128
Reply from 1.1.2.2: bytes=32 time=1ms TTL=128
Ping statistics for 1.1.2.2:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 1ms, Maximum = 1ms, Average = 1ms
# Use the tracert command on Host B to check reachability to Host A.
C:Documents and SettingsAdministrator>tracert 1.1.2.2
Tracing route to 1.1.2.2 over a maximum of 30 hops
1
<1 ms
2
<1 ms
Direct 0
0
Direct 0
0
Direct 0
0
Direct 0
0
Direct 0
0
Direct 0
0
Direct 0
0
Routes : 7
Proto
Pre
Cost
Static 60
0
Direct 0
0
Direct 0
0
Direct 0
0
Direct 0
0
Direct 0
0
Direct 0
0
Routes : 10
Proto
Pre
Cost
Static 60
0
Static 60
0
Direct 0
0
Direct 0
0
Direct 0
0
Direct 0
0
Direct 0
0
Direct 0
0
Direct 0
0
Direct 0
0
<1 ms
<1 ms
1.1.6.1
<1 ms
<1 ms
1.1.4.1
1.1.1.1
Ethernet1/0
127.0.0.1
InLoopBack0
1.1.4.1
Serial2/0
127.0.0.1
InLoopBack0
1.1.4.2
Serial2/0
127.0.0.1
InLoopBack0
127.0.0.1
InLoopBack0Routin
NextHop
Interface
1.1.4.2
Eth1/1
1.1.2.3
Eth1/0
127.0.0.1
InLoop0
1.1.4.1
Eth1/1
127.0.0.1
InLoop0
127.0.0.1
InLoop0
127.0.0.1
InLoop0
NextHop
Interface
1.1.4.1
Eth1/0
1.1.5.6
Eth1/1
1.1.4.2
Eth1/0
127.0.0.1
InLoop0
1.1.5.5
Eth1/1
127.0.0.1
InLoop0
127.0.0.1
InLoop0
127.0.0.1
InLoop0
1.1.6.1
Eth1/2
127.0.0.1
InLoop0
Need help?
Do you have a question about the MSR 50 Series and is the answer not in the manual?
Questions and answers