Advertisement
CHAPTER 17: TEST MODE
3. System & Control Panel Test Mode
No.
Sensors, switches
0001 Wakeup Key
0002 Solenoid counter connection signal Solenoid counter connected
0003 24V A output signal
0004 24V B output signal
Serviceman safety SW (Rear cover
0005
safety SW)
No.
Motor solenoid system
0062 Wakeup LED
No.
Test Print A (checkered)
0080
Creates Test pattern 1 (Checker Flag)
Test Print B (cross stripes)
0081
Creates Test pattern 2 (Cross Lines)
Test Print C (Dot1)
0082
Creates Test pattern 4 (Dot 1 )
Test Print D (Dot2)
0083
Creates Test pattern 5 (Dot 2 )
Test Print E (Dot1 + Cross Lines)
0084
Creates Test pattern 6 (Dot 1 + Cross Lines)
Test Print F (Dot2 + cross stripes)
0085
Creates Test pattern 7 (Dot 2 + Cross Lines)
Test Print G (Dot3)
0086
Creates Test pattern 8 (Dot 3)
Paper-Feed Test (continuous feeding)
Prints continuously.
0087
* The Speed key is enabled.
* If the rear cover safety switch is OFF, the operation begins when the rear cover safety
switch is turned ON within 10 seconds after the START key is turned ON.
Low-Speed Printing Operation
0088
Prints continuously at 15 rpm.
Stepped Printing Operation
Press "Start" key to switch on the suction fan. Prints at 15 rpm only while "Test print" key is
0089
pressed.
Printing stops when "Test Print" key is released, and resumes if the key is pressed again.
Press "Stop" to switch suction fan off.
Unit Initialization
Initializes the mechanical moving units to their home positions.
RZ3:TPH pressure, master compression plate, drum lock, clamp unit, vertical print position,
printing pressure.
0094
RZ5:TPH pressure, master compression plate, drum lock, clamp unit, vertical print position,
printing pressure,
Paper Ejection Wing.
RZ9:scanner, thermal print head, compression plate, clamp units, vertical print position,
printing pressure.
System Configuration Data Output
0095
Creates a master for the CI system data.
Data-Setting & Error-History Output
0097
Creates a master for the list of data-setting changes and the error history.
Error Record
0099
Stores the error logs accumulated on FLASH memory into CF card.
Rev Manual Event Code Set
0100
Stores the settings set in Test mode "No. 196 to 198" manual event codes into REv Flash
address in CF card.
Machine Clock Activation
Activates time set by Test Modes No.0171 to 0173. The new clock time set by test mode
0101
No. 0171 through No.0173 will not be activated unless this test mode No. 0101 is activated.
Pressing the Start key begins the operation and automatically stops it after 0.5 seconds.
DANKA AUSTRALIA PTY. LTD.
Key Pressed
24V-A ON (24V output)
24V-B ON (24V output)
Switch ON (main unit rear cover is installed)
Other safety switches must be ON for this check.
LED Illuminates
Unit check
[ 17 - 4 ] - Rev. 0.2
Detection status
3
5
9
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
3
5
9
o
o
o
3
5
9
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
x
x
o
o
o
o
o
o
o
o
o
x
o
o
o
o
o
o
x
o
o
o
o
o
o
o
o
o
o
o
RZ9 Series
Advertisement
Chapters
