Riso RZ9 Series Technical Manual page 414

CHAPTER 16: PANEL MESSAGE
Error Type T98 [Hardware error]
T98-xxx
!!System Error!!
Description
Press Reset Key
If Recovery has Failed, Call Service
To reset
Turn power OFF and ON.
display
Error Point
075 Communication error between SH PCB and MCTL PCB (11) - on SH PCB side.
076 Communication error between SH PCB and MCTL PCB (12) - on SH PCB side.
077 Communication error between SH PCB and MCTL PCB (13) - on SH PCB side.
078 Communication error between SH PCB and MCTL PCB (14) - on SH PCB side.
079 Communication error between SH PCB and MCTL PCB (15) - on SH PCB side.
080 Communication error between SH PCB and MCTL PCB (16) - on SH PCB side.
081 Communication error between SH PCB and MCTL PCB (17) - on SH PCB side.
082 Communication error between SH PCB and MCTL PCB (18) - on SH PCB side.
083 Communication error between SH PCB and MCTL PCB (19) - on SH PCB side.
084 Communication error between SH PCB and MCTL PCB (20) - on SH PCB side.
098 Machine serial number information on EEPROM does not match with that of FRAM.
119 Defective image PCB (memory check error on the image processing IC).
120 Timeout on the scanner serial communication.
129 Defective scanner gate array PCB (memory check error on the gate array).
245 Timeout error on master transfer during master-making (related to Write pulse motor).
246 Timeout error on master transfer during master-making (related to Load pulse motor).
The light emittance from the Paper sensor (send) exceeded the maximum allowance
422 during the Automatic Multiple Paper Feed Adjustment [paper sensor sensitivity
adjustment] by Test Mode No.705.
The light emittance from the Paper sensor (send) exceeded the minimum allowance
423 during the Automatic Multiple Paper Feed Adjustment [paper sensor sensitivity
adjustment] by Test Mode No.705.
921 The USB controler chip is not responding when PC and printer is connected by USB cable. x
934 Communication error between MCTL PCB and RF PCB. (on FR PCB side)
935 Communication error between MCTL PCB and RF PCB. (on MCTL PCB side)
937 Undefined serial number.
938 FRAM version down.
947 24V-A does not go ON. (Possible broken Fuse for 24V-A area).
948 24V-A does not go ON. (Possible broken Fuse for 24V-B area).
949 24V-A does not go OFF.
950 24V-B does not go OFF.
952 SH3M2 PCB flash memory check-sum error.
953 Unsuccessful writing on the SH3M2 PCB flash memory.
960 Unsuccessful readout from the SH3M2 PCB flash memory.
961 SH3M2 PCB flash memory unused.
978 Incorrect power ON command from MCTL PCB when machine power turned ON.
979 Abnormal flash memory setting on the SH3M2 PCB.
983 24V-C does not go ON. (Possible broken Fuse for 24V-C area).
984 24V-C does not go OFF.
Error Type T99 [Software error]
T99-xxx
!!System Error!!
Description
Press Reset Key
If Recovery has Failed, Call Service
To reset
Turn power OFF and ON.
display
Error Point
181 Timeout on Image processing time.
982 Wrong loader.
DANKA AUSTRALIA PTY. LTD.
Error Conditions
Error Conditions
[ 16 - 18 ] - Rev. 0.2
3 5 9
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
x x O
x x O
x O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
x O O
x O O
x O O
x O O
x x O
x x O
3 5 9
x x O
x O x
RZ9 Series