Siemens SINUMERIK Series Operating Manual page 14
Milling
Hide thumbs
Also See for SINUMERIK Series:
- Function manual (956 pages) ,
- Function manual (204 pages) ,
- Function manual (332 pages)
Table of Contents
Advertisement
Table of contents
10.2
Milling...................................................................................................................................420
10.2.1
Face milling (CYCLE61).......................................................................................................420
10.2.2
Rectangular pocket (POCKET3)..........................................................................................422
10.2.3
Circular pocket (POCKET4).................................................................................................429
10.2.4
Rectangular spigot (CYCLE76)............................................................................................436
10.2.5
Circular spigot (CYCLE77)...................................................................................................441
10.2.6
Multi-edge (CYCLE79).........................................................................................................445
10.2.7
Longitudinal groove (SLOT1)...............................................................................................449
10.2.8
Circumferential groove (SLOT2)..........................................................................................455
10.2.9
Open groove (CYCLE899)...................................................................................................461
10.2.10
Long hole (LONGHOLE) - only for G code programs..........................................................469
10.2.11
Thread milling (CYCLE70)...................................................................................................471
10.2.12
Engraving (CYCLE60)..........................................................................................................475
10.3
Contour milling.....................................................................................................................481
10.3.1
General................................................................................................................................481
10.3.2
Representation of the contour..............................................................................................481
10.3.3
Creating a new contour........................................................................................................483
10.3.4
Creating contour elements...................................................................................................484
10.3.5
Changing the contour...........................................................................................................489
10.3.6
Contour call (CYCLE62) - only for G code program.............................................................490
10.3.7
Path milling (CYCLE72).......................................................................................................491
10.3.8
Contour pocket/contour spigot (CYCLE63/64).....................................................................496
10.3.9
Predrilling contour pocket (CYCLE64).................................................................................498
10.3.10
Milling contour pocket (CYCLE63).......................................................................................501
10.3.11
Residual material contour pocket (CYCLE63).....................................................................506
10.3.12
Milling contour spigot (CYCLE63)........................................................................................507
10.3.13
Residual material contour spigot (CYCLE63)......................................................................511
10.4
Turning - milling/turning machine.........................................................................................514
10.4.1
General................................................................................................................................514
10.4.2
Stock removal (CYCLE951).................................................................................................514
10.4.3
Groove (CYCLE930)............................................................................................................518
10.4.4
Undercut form E and F (CYCLE940)...................................................................................523
10.4.5
Thread undercut (CYCLE940).............................................................................................529
10.4.6
Thread turning (CYCLE99), only for G code........................................................................534
10.4.7
Thread chain (CYCLE98).....................................................................................................561
10.4.8
Cut-off (CYCLE92)...............................................................................................................570
10.5
Contour turning - Milling/turning machine............................................................................574
10.5.1
General information..............................................................................................................574
10.5.2
Representation of the contour..............................................................................................575
10.5.3
Creating a new contour........................................................................................................576
10.5.4
Creating contour elements...................................................................................................578
10.5.5
Changing the contour...........................................................................................................584
10.5.6
Contour call (CYCLE62).......................................................................................................585
10.5.7
Stock removal (CYCLE952).................................................................................................586
10.5.8
Stock removal residual (CYCLE952)...................................................................................599
10.5.9
Grooving (CYCLE952).........................................................................................................603
10.5.10
Grooving residual material (CYCLE952)..............................................................................613
10.5.11
Plunge turning (CYCLE952).................................................................................................617
10.5.12
Plunge turning residual material (CYCLE952).....................................................................627
10.6
Further cycles and functions................................................................................................631
14
Operating Manual, 08/2018, 6FC5398-7CP41-0BA0
Milling
Advertisement
Table of Contents
