Agilent Technologies InfiniiVision 5000 Series Programmer's Manual page 786

Index
trigger, glitch polarity, 449
trigger, glitch qualifier, 450
trigger, glitch range, 451
trigger, glitch source, 452
trigger, high frequency reject filter,
trigger, holdoff, 416
trigger, IIC clock source, 457
trigger, IIC data source, 458
trigger, IIC pattern address, 454
trigger, IIC pattern data, 455
trigger, IIC pattern data 2, 456
trigger, IIC qualifier, 459
trigger, IIC signal baudrate, 465
trigger, IIC type, 460
trigger, LIN, 469
trigger, LIN sample point, 464
trigger, LIN signal definition, 612
trigger, LIN source, 466
trigger, mode, 417
trigger, noise reject filter, 418
trigger, pattern, 419
trigger, SPI clock slope, 471
trigger, SPI clock source, 476
trigger, SPI clock timeout, 472
trigger, SPI data source, 477
trigger, SPI frame source, 478
trigger, SPI framing, 473
trigger, SPI pattern data, 474
trigger, SPI pattern width, 475
trigger, sweep, 421
trigger, TV line, 480
trigger, TV mode, 481, 613
trigger, TV polarity, 482
trigger, TV source, 483
trigger, TV standard, 484
trigger, UART base, 487
trigger, UART baudrate, 488
trigger, UART bit order, 489
trigger, UART parity, 493
trigger, UART polarity, 494
trigger, UART Rx source, 496
trigger, UART Tx source, 497
trigger, UART width, 499
truncation rules, 660
TST (Self Test), 120
tstart, 591
tstop, 592
turn function on or off, 577
turn off channel, 130
turn off channel labels, 213
turn off cursors, 126
turn off digital pod, 130
turn off math function, 130
turn off measurements, 126
turn off trace memories, 126
turn off zoomed time base mode,
turn on channel labels, 213
turn on channels, 126
turning channel display on and off,
turning off/on function calculation,
turning vectors on or off, 572
TV mode, 481, 613
786
TV trigger commands,
TV trigger line number setting,
TV trigger mode,
TV trigger polarity,
415 TV trigger standard setting,
TV triggering,
tvmode, 613
Tx data, UART,
Tx frame count (UART),
Tx source, 497
type, 177, 526
TYPE commands,
U
UART base, 487
UART baud rate,
UART bit order,
UART commands,
UART frame counters, reset,
UART parity, 493
UART polarity,
UART Rx source,
UART trigger burst,
UART trigger commands,
UART trigger data,
UART trigger idle,
UART trigger qualifier,
UART trigger type,
UART Tx data,
UART Tx source,
UART width, 499
UNITs commands,
units per division, 205, 206, 227,
units per division (vertical) for function, 205,
240
units, automask,
unsigned mode,
upper threshold,
upper threshold voltage for measurement,
uppercase characters in commands,
URQ (User Request) status bit, 103,
USB (Device) interface,
user defined channel labels,
user event conditions occurred,
User's Guide, 4
USR (User Event bit), 116,
Utility button, 33,
utilization, CAN bus,
V
valid command strings,
valid pattern time, 434,
value, 304
126
value measured at base of waveform,
value measured at specified time,
value measured at top of waveform,
194
value ranges,
232
values required to fill time buckets,
VBA, 44, 744
479
480
483
482
484
411
525
389
558
488
489
558
387
494
496
490
485
491
492
495
498
525
497
559
406
325
527
287
595
659
105
33
197
118
118
34
379
659
435
308
314
315
93
167
Agilent InfiniiVision 5000 Series Oscilloscopes Programmer's Guide
vectors, 217
vectors turned on or off, 572
vectors, turning on or off, 208
vernier, channel, 207
vernier, horizontal, 407
vertical adjustment, fine (vernier),
vertical amplitude measurement,
vertical axis defined by RANGe, 238
vertical axis range for channels, 204
vertical offset for channels, 198
vertical peak-to-peak measured on
waveform, 311
vertical scale, 205, 240
vertical scaling, 516
vertical value at center screen, 236,
vertical value maximum measured on
waveform, 309
vertical value measurements to calculate
overshoot, 285
vertical value minimum measured on
waveform, 310
video line to trigger on, 480
video standard selection, 484
view, 162, 230, 528
view turns function on or off, 577
VISA COM example in C#, 754
VISA COM example in Visual Basic,
VISA COM example in Visual Basic .NET,
VISA example in C, 698
VISA example in C#, 717
VISA example in Visual Basic, 707
VISA example in Visual Basic .NET,
VISA examples, 698, 744
Visual Basic .NET, VISA COM example,
Visual Basic .NET, VISA example,
Visual Basic 6.0, 45
Visual Basic for Applications, 44,
Visual Basic, SICL library example,
Visual Basic, VISA COM example,
Visual Basic, VISA example, 707
voltage crossing reported or not found,
voltage difference between data points,
voltage difference measured, 596
voltage level for active trigger, 441
voltage marker used to measure
waveform, 597, 598
voltage offset value for channels,
voltage probe, 206, 227
voltage ranges for channels, 204
voltage ranges for external trigger,
voltage threshold, 277
W
WAI (Wait To Continue), 121
wait, 121
wait for operation complete, 108
Wait Trig bit, 147, 149
waveform base value measured,
WAVeform command, 43
WAVeform commands, 500, 560
waveform data, 502
207
306
239
744
765
731
765
731
744
689
744
593
532
198
226
308