Agilent Technologies InfiniiVision 5000 Series Programmer's Manual page 783

P
P1080L24HZ, 480, 484
P1080L25HZ, 480, 484
P480L60HZ, 480, 484
P720L60HZ, 480, 484
PAL, 480, 484
PALette commands, 548
palette for hardcopy, 253
palette for image, 365
PAL-M, 480, 484
parameters for delay measurement,
parametric measurements, 272
parity, 493
parity bits, LIN serial decode bus,
PARity commands, 548
parser, 124, 675
pass (mask test) output, 336
pass, self test, 120
path information, recall, 355
path information, save, 367
pattern, 419, 424, 426, 436, 454, 455, 456,
474
pattern and edge, 419
PATTern commands, 548
pattern duration, 434, 435, 446,
pattern length, 425
pattern trigger, 419
pattern triggering, 411
pattern width, 475
peak detect, 177
peak detect acquisition type, 164,
peaks, 230
peak-to-peak vertical value measurement,
pending operations, 108
percent of waveform overshoot,
percent thresholds, 277
period measured to calculate phase,
period measurement, 43, 272, 287
persistence, waveform, 208, 215
phase measured between channels,
phase measurements, 302
pixel memory, 216
pixel memory, saving display to, 140
PLL Locked bit, 136, 147
pod, 521
pod, stop displaying, 130
points, 170, 512, 514
POINts commands, 549
points in waveform data, 502
polarity, 482, 494
POLarity commands, 549
polarity for glitch trigger, 449
polling synchronization with timeout,
polling wait, 648
PON (Power On) status bit, 103,
portrait layout for hardcopy, 252
position, 261, 403, 408
POSition commands, 549
position cursors, 591, 592
position in zoomed view, 408
positive glitch trigger polarity, 449
Agilent InfiniiVision 5000 Series Oscilloscopes Programmer's Guide
positive pulse width,
positive pulse width measurement,
positive slope, 443,
positive TV trigger polarity,
positive width,
preamble data, 502,
present working directory, recall
operations,
present working directory, save operations,
preset conditions,
preshoot measured on waveform,
previously stored configuration,
279
print command,
print job, start,
print mask test failures,
382
print query, 607
printer, 579
printer driver for hardcopy,
printer hardcopy format,
printer, active,
printing, 246
printing in grayscale,
probe, 441
probe attenuation affects channel voltage
range, 204
probe attenuation factor (external trigger),
447
probe attenuation factor for selected
channel,
PROBe commands,
probe ID, 200,
probe sense for oscilloscope, 571,
probe skew value, 201,
502
process sigma, mask test run,
program data,
311
program data syntax rules,
program initialization,
285
program message, 45,
program message syntax,
288
program message terminator,
program structure,
programming examples, 4,
288
protecting against calibration,
protection, 151, 153, 203,
PROTection commands,
protection lock,
pulse width, 284,
pulse width duration trigger, 446, 447,
pulse width measurement, 43,
pulse width trigger,
pulse width trigger level,
pulse width triggering,
PWD commands,
pwidth, 290
650
Q
105
qualifier, 451
QUALifier commands,
qualifier, trigger duration, 434, 435,
queries, multiple,
query error detected in Standard Event
Status, 105
290
43
471
482
290
516
355
367
111
289
110
155
255
338
584
581
248
582
222
199
549
223
575
569
341
660
662
42
99
659
660
42
679
186
225
549
396
290
451
272
418
448
411
549
549
437
51
query responses, block data, 50
query responses, reading, 49
query results, reading into numeric
variables, 50
query results, reading into string variables,
query return values, 677
query setup, 246, 257, 272, 397
query subsystem, 230
querying setup, 190
querying the subsystem, 411
queues, clearing, 645
quick reference, commands, 55
quoted ASCII string, 93
QYE (Query Error) status bit, 103,
R
range, 230, 409
RANGe commands, 550
range for channels, 204
range for duration trigger, 438
range for external trigger, 226
range for full-scale vertical axis,
range for glitch trigger, 451
range for time base, 404
range of offset values, 198
range qualifier, 450
ranges, value, 93
rate, 176
ratio of AC RMS values measured between
channels, 312
RCL (Recall), 110
read configuration, 107
read trace memory, 211
ReadIEEEBlock method, 45, 49,
ReadList method, 45, 49
ReadNumber method, 45, 49
readout, 587
ReadString method, 45, 49
real-time acquisition mode, 164,
recall, 110, 351, 397
RECall commands, 351
recall filename, 352
recall image, 353
recall mask, 354
recall path information, 355
recall setup, 356
recalling and saving data, 208
RECTangular window for transient signals,
reference, 230, 405
REFerence commands, 550
reference for time base, 609
registers, 104, 110, 114, 125, 134, 136, 138,
141, 143, 145, 147, 149, 151,
registers, clearing, 645
reject filter, 442
reject high frequency, 415
reject noise, 418
remote control examples, 679
remove cursor information, 258
remove labels, 213
remove message from display, 393
Index
50
105
238
51
169
244
153
783